100% Latest & Updated Fortinet NSE7_SSE_AR-26 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 360
Select THREE correct elements of a safe remedy-and-evidence plan for the IKE negotiation dependency case. Following a production change affecting Brookfield Media in its western region, a network team receives repeatable user-impact reports. Its fault evidence is: An IPsec overlay tunnel fails because peer proposals have no common acceptable IKE parameters. Unrelated services are still operating, so the immediate response must isolate the failing control for one approved pilot tenant without disabling unrelated protections.
- Align supported IKE versions and cryptographic proposals under the approved security baseline on both peers.
- The tunnel establishes using the intended approved cryptography.
- Examine IKE negotiation diagnostics for a successful agreed proposal and established SA.
- Use a lowest-cost strategy conditioned on qualified SLA members instead of price alone.
- Marked voice follows the selected policy while ordinary packets retain the default behavior.
- Correlate service-rule selection with firewall policy decision for the same five-tuple flow.
Explanation
Correct Answers
A:Correct remediation element: Align supported IKE versions and cryptographic proposals under the approved security baseline on both peers. It addresses Peer IKE proposal mismatch prevents establishment despite reachable underlays. [Case R161-C072; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0360.]
B:The tunnel establishes using the intended approved cryptography. This confirms the case-specific path or security boundary.
C:Correct verification element: Examine IKE negotiation diagnostics for a successful agreed proposal and established SA. This independently measures whether the intended change works. [Case R161-C072; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0360.]
Incorrect Answers
D:That intervention addresses Lowest-cost strategy with SLA floor: A branch chooses the cheapest circuit even when it misses the required application latency target. The case-specific requirement is: Align supported IKE versions and cryptographic proposals under the approved security baseline on both peers. Verify it with: Examine IKE negotiation diagnostics for a successful agreed proposal and established SA.
E:Incorrect for this case: Marked voice follows the selected policy while ordinary packets retain the default behavior. concerns the separate issue of DSCP-aware application steering (Priority voice packets use the ordinary bulk-data member because the existing service rule ignores markings.). It does not directly establish The tunnel establishes using the intended approved cryptography. The case-specific evidence is Examine IKE negotiation diagnostics for a successful agreed proposal and established SA. [Case R161-C072; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0360.]
F:Incorrect for this case: Correlate service-rule selection with firewall policy decision for the same five-tuple flow. concerns the separate issue of Steering policy versus firewall permission (An engineer adds an SD-WAN rule but a restricted application remains blocked at the firewall policy layer.). It does not directly establish Examine IKE negotiation diagnostics for a successful agreed proposal and established SA. The case-specific evidence is Examine IKE negotiation diagnostics for a successful agreed proposal and established SA. [Case R161-C072; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0360.]
Question 361
Which corrective action MOST DIRECTLY addresses the observed IPsec selector scope problem within the approved change scope? During a scoped coastal district deployment across a staged branch cohort, Beaconline Support must commission the planned FortiSASE/SD-WAN control. The operational finding is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The change ticket limits modifications to the new branch group and requires a reversible test.
- Inspect policy-route and routing-table precedence, then reconcile conflicting forwarding rules.
- Make the protected traffic selectors match the approved overlay encryption scope.
- Inspect existing session behavior and reevaluation triggers; plan a scoped session reset only if required and safe.
- Add or correct the scoped route to the SD-WAN zone and confirm member selection remains governed by rules.
Explanation
Correct Answer
B:Correct: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The targeted remedy is Make the protected traffic selectors match the approved overlay encryption scope. This addresses an ipsec phase-two selector mismatch excludes desired traffic. Confirm it by: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0361.]
Incorrect Answers
A:That intervention addresses Policy route overriding intended SD-WAN path: A destination uses an unexpected interface despite a healthy specific SD-WAN service rule. The case-specific requirement is: Make the protected traffic selectors match the approved overlay encryption scope. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
C:That intervention addresses Session persistence after route change: Existing SNAT flows remain on the old egress after a route change while new sessions use the new link. The case-specific requirement is: Make the protected traffic selectors match the approved overlay encryption scope. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
D:Incorrect for this case: Add or correct the scoped route to the SD-WAN zone and confirm member selection remains governed by rules. concerns the separate issue of Static zone route missing (A security policy allows traffic on an SD-WAN zone but its destination has no usable route through that zone.). It does not directly establish Make the protected traffic selectors match the approved overlay encryption scope. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0361.]
Question 362
Which independent diagnostic check best validates that the IPsec selector scope repair works? During a scoped coastal district deployment across a staged branch cohort, Beaconline Support must commission the planned FortiSASE/SD-WAN control. The operational finding is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The change ticket limits modifications to the new branch group and requires a reversible test.
- Inspect the BGP next hop, recursive route and data-plane egress for a test LAN destination.
- Inspect rule diagnostics for eligible members and create a new test session after change.
- Compare allowed and denied BGP prefix sets before and after updating the filter.
- Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
Explanation
Correct Answer
D:Correct: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. This directly tests the failure mechanism and the required acceptance evidence: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0362.]
Incorrect Answers
A:Incorrect for this case: Inspect the BGP next hop, recursive route and data-plane egress for a test LAN destination. concerns the separate issue of Overlay route recursive next hop (A BGP-learned LAN prefix appears in the control plane but fails recursive resolution to a usable tunnel.). It does not directly establish Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0362.]
B:Incorrect for this case: Inspect rule diagnostics for eligible members and create a new test session after change. concerns the separate issue of Rule monitoring after topology change (A new circuit was added but no sessions move to it even though it meets the SLA.). It does not directly establish Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0362.]
C:That intervention addresses BGP filtering for tenant scope: Two SD-WAN sites exchange too many prefixes and a branch learns another tenant's private networks. The relevant verification here is: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
Question 363
What observable result would show that the intended IPsec selector scope behavior has been restored? During a scoped coastal district deployment across a staged branch cohort, Beaconline Support must commission the planned FortiSASE/SD-WAN control. The operational finding is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The change ticket limits modifications to the new branch group and requires a reversible test.
- Permitted private subnets traverse the established overlay without widening selectors unnecessarily.
- The new circuit becomes eligible for the specified traffic instead of remaining unused.
- Operators distinguish session persistence from a failed routing-policy update.
- The destination resolves through the intended zone and authorized member.
Explanation
Correct Answer
A:Correct: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. That result demonstrates the requested controlled repair and avoids the failure mode: An IPsec phase-two selector mismatch excludes desired traffic. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0363.]
Incorrect Answers
B:Incorrect for this case: The new circuit becomes eligible for the specified traffic instead of remaining unused. concerns the separate issue of Rule monitoring after topology change (A new circuit was added but no sessions move to it even though it meets the SLA.). It does not directly establish Permitted private subnets traverse the established overlay without widening selectors unnecessarily. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0363.]
C:That intervention addresses Session persistence after route change: Existing SNAT flows remain on the old egress after a route change while new sessions use the new link. The case-specific requirement is: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
D:That intervention addresses Static zone route missing: A security policy allows traffic on an SD-WAN zone but its destination has no usable route through that zone. The case-specific requirement is: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
Question 364
Which failure mechanism BEST explains the IPsec selector scope observation before a repair is attempted? During a scoped coastal district deployment across a staged branch cohort, Beaconline Support must commission the planned FortiSASE/SD-WAN control. The operational finding is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The change ticket limits modifications to the new branch group and requires a reversible test.
- An IPsec phase-two selector mismatch excludes desired traffic.
- The service rule lacks the classification needed to distinguish marked traffic.
- Static IP lists no longer represent the intended SaaS service.
- SD-WAN path selection does not itself grant firewall permission.
Explanation
Correct Answer
A:Correct: An IPsec phase-two selector mismatch excludes desired traffic. This matches the given observation, unlike defects in unrelated SASE or SD-WAN controls. Verify the diagnosis through: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0364.]
Incorrect Answers
B:The DSCP-aware application steering diagnosis does not explain the observed case: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The supported diagnosis is: An IPsec phase-two selector mismatch excludes desired traffic.
C:The Internet-service destination matching diagnosis does not explain the observed case: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The supported diagnosis is: An IPsec phase-two selector mismatch excludes desired traffic.
D:The Steering policy versus firewall permission diagnosis does not explain the observed case: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The supported diagnosis is: An IPsec phase-two selector mismatch excludes desired traffic.
Question 365
Select TWO correct elements of a safe remedy-and-evidence plan for the IPsec selector scope case. During a scoped coastal district deployment across a staged branch cohort, Beaconline Support must commission the planned FortiSASE/SD-WAN control. The operational finding is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The change ticket limits modifications to the new branch group and requires a reversible test.
- Make the protected traffic selectors match the approved overlay encryption scope.
- Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
- Account for application identification and learning; use a safe initial match strategy until the flow is classified.
- Only intended site routes propagate without exposing unrelated tenant networks.
- Correlate service-rule selection with firewall policy decision for the same five-tuple flow.
Explanation
Correct Answers
A:Correct remediation element: Make the protected traffic selectors match the approved overlay encryption scope. It addresses An IPsec phase-two selector mismatch excludes desired traffic. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0365.]
B:Correct verification element: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. This independently measures whether the intended change works. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0365.]
Incorrect Answers
C:That intervention addresses Application learning before classification: A newly introduced application is initially unidentified, so flows take an unexpected fallback member. The case-specific requirement is: Make the protected traffic selectors match the approved overlay encryption scope. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
D:Incorrect for this case: Only intended site routes propagate without exposing unrelated tenant networks. concerns the separate issue of BGP filtering for tenant scope (Two SD-WAN sites exchange too many prefixes and a branch learns another tenant's private networks.). It does not directly establish Permitted private subnets traverse the established overlay without widening selectors unnecessarily. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C073; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0365.]
E:That intervention addresses Steering policy versus firewall permission: An engineer adds an SD-WAN rule but a restricted application remains blocked at the firewall policy layer. The relevant verification here is: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
Question 366
Which corrective action MOST DIRECTLY addresses the observed IPsec selector scope problem within the approved change scope? Following a production change affecting Ironleaf Agriculture in its metro branch group, a network team receives repeatable user-impact reports. Its fault evidence is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. Unrelated services are still operating, so the immediate response must isolate the failing control for the designated privileged users without disabling unrelated protections.
- Apply a scoped DSCP-aware SD-WAN steering condition where the marked traffic should receive special handling.
- Make the protected traffic selectors match the approved overlay encryption scope.
- Add or correct the scoped route to the SD-WAN zone and confirm member selection remains governed by rules.
- Validate health signaling and route preference over both hub overlays, then correct the preference condition.
Explanation
Correct Answer
B:Correct: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The targeted remedy is Make the protected traffic selectors match the approved overlay encryption scope. This addresses an ipsec phase-two selector mismatch excludes desired traffic. Confirm it by: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0366.]
Incorrect Answers
A:That intervention addresses DSCP-aware application steering: Priority voice packets use the ordinary bulk-data member because the existing service rule ignores markings. The case-specific requirement is: Make the protected traffic selectors match the approved overlay encryption scope. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
C:Incorrect for this case: Add or correct the scoped route to the SD-WAN zone and confirm member selection remains governed by rules. concerns the separate issue of Static zone route missing (A security policy allows traffic on an SD-WAN zone but its destination has no usable route through that zone.). It does not directly establish Make the protected traffic selectors match the approved overlay encryption scope. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0366.]
D:That intervention addresses Dual-hub routing failover evidence: A spoke sees both hub routes but continues preferring the failed region when the primary becomes unhealthy. The case-specific requirement is: Make the protected traffic selectors match the approved overlay encryption scope. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
Question 367
Which independent diagnostic check best validates that the IPsec selector scope repair works? Following a production change affecting Ironleaf Agriculture in its metro branch group, a network team receives repeatable user-impact reports. Its fault evidence is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. Unrelated services are still operating, so the immediate response must isolate the failing control for the designated privileged users without disabling unrelated protections.
- Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
- Trace route lookup for the target prefix and compare with the SD-WAN policy match.
- Inspect the BGP next hop, recursive route and data-plane egress for a test LAN destination.
- Inspect the egress member for allowed vendor flows and confirm other applications retain dynamic rules.
Explanation
Correct Answer
A:Correct: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. This directly tests the failure mechanism and the required acceptance evidence: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0367.]
Incorrect Answers
B:That intervention addresses Policy route overriding intended SD-WAN path: A destination uses an unexpected interface despite a healthy specific SD-WAN service rule. The relevant verification here is: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
C:Incorrect for this case: Inspect the BGP next hop, recursive route and data-plane egress for a test LAN destination. concerns the separate issue of Overlay route recursive next hop (A BGP-learned LAN prefix appears in the control plane but fails recursive resolution to a usable tunnel.). It does not directly establish Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0367.]
D:That intervention addresses Manual strategy for fixed egress: A regulated vendor demands a known egress interface rather than opportunistic best-quality switching. The relevant verification here is: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
Question 368
What observable result would show that the intended IPsec selector scope behavior has been restored? Following a production change affecting Ironleaf Agriculture in its metro branch group, a network team receives repeatable user-impact reports. Its fault evidence is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. Unrelated services are still operating, so the immediate response must isolate the failing control for the designated privileged users without disabling unrelated protections.
- The new circuit becomes eligible for the specified traffic instead of remaining unused.
- Permitted private subnets traverse the established overlay without widening selectors unnecessarily.
- Only intended site routes propagate without exposing unrelated tenant networks.
- Each spoke maintains distinct BGP identity and stable LAN route attribution.
Explanation
Correct Answer
B:Correct: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. That result demonstrates the requested controlled repair and avoids the failure mode: An IPsec phase-two selector mismatch excludes desired traffic. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0368.]
Incorrect Answers
A:Incorrect for this case: The new circuit becomes eligible for the specified traffic instead of remaining unused. concerns the separate issue of Rule monitoring after topology change (A new circuit was added but no sessions move to it even though it meets the SLA.). It does not directly establish Permitted private subnets traverse the established overlay without widening selectors unnecessarily. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0368.]
C:Incorrect for this case: Only intended site routes propagate without exposing unrelated tenant networks. concerns the separate issue of BGP filtering for tenant scope (Two SD-WAN sites exchange too many prefixes and a branch learns another tenant's private networks.). It does not directly establish Permitted private subnets traverse the established overlay without widening selectors unnecessarily. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0368.]
D:That intervention addresses BGP loopback duplicate identity: Two spokes share a loopback address, causing unstable BGP peering and route attribution. The case-specific requirement is: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
Question 369
Which failure mechanism BEST explains the IPsec selector scope observation before a repair is attempted? Following a production change affecting Ironleaf Agriculture in its metro branch group, a network team receives repeatable user-impact reports. Its fault evidence is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. Unrelated services are still operating, so the immediate response must isolate the failing control for the designated privileged users without disabling unrelated protections.
- A generic dynamic steering strategy cannot guarantee fixed vendor egress.
- A higher-precedence policy route changes path selection.
- Tunnel establishment alone does not guarantee route exchange.
- An IPsec phase-two selector mismatch excludes desired traffic.
Explanation
Correct Answer
D:Correct: An IPsec phase-two selector mismatch excludes desired traffic. This matches the given observation, unlike defects in unrelated SASE or SD-WAN controls. Verify the diagnosis through: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0369.]
Incorrect Answers
A:The Manual strategy for fixed egress diagnosis does not explain the observed case: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The supported diagnosis is: An IPsec phase-two selector mismatch excludes desired traffic.
B:The Policy route overriding intended SD-WAN path diagnosis does not explain the observed case: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The supported diagnosis is: An IPsec phase-two selector mismatch excludes desired traffic.
C:The BGP route visibility after tunnel recovery diagnosis does not explain the observed case: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. The supported diagnosis is: An IPsec phase-two selector mismatch excludes desired traffic.
Question 370
Select THREE correct elements of a safe remedy-and-evidence plan for the IPsec selector scope case. Following a production change affecting Ironleaf Agriculture in its metro branch group, a network team receives repeatable user-impact reports. Its fault evidence is: IKE phase one succeeds but traffic selectors prevent the intended private subnet from crossing the overlay. Unrelated services are still operating, so the immediate response must isolate the failing control for the designated privileged users without disabling unrelated protections.
- The vendor gets the required egress control without forcing all traffic onto one member.
- Use a lowest-cost strategy conditioned on qualified SLA members instead of price alone.
- Inspect rule diagnostics for eligible members and create a new test session after change.
- Permitted private subnets traverse the established overlay without widening selectors unnecessarily.
- Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
- Make the protected traffic selectors match the approved overlay encryption scope.
Explanation
Correct Answers
D:Permitted private subnets traverse the established overlay without widening selectors unnecessarily. This confirms the case-specific path or security boundary.
E:Correct verification element: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. This independently measures whether the intended change works. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0370.]
F:Correct remediation element: Make the protected traffic selectors match the approved overlay encryption scope. It addresses An IPsec phase-two selector mismatch excludes desired traffic. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0370.]
Incorrect Answers
A:That intervention addresses Manual strategy for fixed egress: A regulated vendor demands a known egress interface rather than opportunistic best-quality switching. The case-specific requirement is: Permitted private subnets traverse the established overlay without widening selectors unnecessarily. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
B:That intervention addresses Lowest-cost strategy with SLA floor: A branch chooses the cheapest circuit even when it misses the required application latency target. The case-specific requirement is: Make the protected traffic selectors match the approved overlay encryption scope. Verify it with: Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel.
C:Incorrect for this case: Inspect rule diagnostics for eligible members and create a new test session after change. concerns the separate issue of Rule monitoring after topology change (A new circuit was added but no sessions move to it even though it meets the SLA.). It does not directly establish Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. The case-specific evidence is Inspect phase-two SA selectors and send the intended subnet traffic across the tunnel. [Case R161-C074; Fortinet task T3; anchors EXAM, ADVPN, FMG_BGP.] [Question R161-Q0370.]
Fortinet NSE 7 - FortiSASE 26 Architect (NSE7_SSE_AR-26) Practice Tests