100% Latest & Updated Juniper JN0-364 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 120
Operations sees repeated OSPF hellos on a customer link where only prefix reachability was intended, not protocol adjacency. Independently, the review flags the potentially unsafe practice “Treat zero hellos as sufficient proof that destinations still route”. Which validation addresses the risk without assuming a particular cause?
- Verify internal core-facing neighbors remain Full
- Inspect passive-interface status and advertised network
- Inspect advertised prefix and remote reachability after change
- Accept OSPF neighbors from every customer access connection by default
Explanation
Correct Answer
C:Passive success alone does not verify route propagation. Control-plane silence should not remove needed reachability.
Incorrect Answers
A:Core neighbors are necessary for internal route exchange.
B:Passive mode can advertise connected reachability without neighbor hellos.
D:Unauthorized adjacency can inject incorrect topology.
Question 121
A provider upgraded one core link from 10 Gbps to 100 Gbps yet OSPF continues to favor an older path; link costs appear equal. The objective is to review actual interface costs. Which Junos configuration or design action best satisfies the objective?
- Declare success from a committed cost value without testing path changes
- Change reference bandwidth on one router without assessing the topology
- Inspect OSPF effective costs on all competing paths
- Choose the route solely because its last hop has the fastest port
Explanation
Correct Answer
C:SPF selects using link-state topology and path cost.
Incorrect Answers
A:Configuration state alone is not proof of intended egress.
B:One-sided metric policy can cause inconsistent path computation.
D:The complete path cost can differ from its final hop.
Question 122
A provider upgraded one core link from 10 Gbps to 100 Gbps yet OSPF continues to favor an older path; link costs appear equal. The objective is to harmonize reference bandwidth. Which operational choice should be prioritized in this design?
- Apply a consistent approved OSPF reference-bandwidth policy across routers
- Declare success from a committed cost value without testing path changes
- Choose the route solely because its last hop has the fastest port
- Assume higher interface speed always changes OSPF cost automatically
Explanation
Correct Answer
A:Inconsistent reference bandwidth can produce asymmetric path preferences.
Incorrect Answers
B:Configuration state alone is not proof of intended egress.
C:The complete path cost can differ from its final hop.
D:Cost depends on configured and reference bandwidth behavior.
Question 123
A provider upgraded one core link from 10 Gbps to 100 Gbps yet OSPF continues to favor an older path; link costs appear equal. The objective is to compute total path cost. Which routing or switching control best fits the requirement?
- Change reference bandwidth on one router without assessing the topology
- Evaluate cumulative link costs rather than one interface alone
- Assume higher interface speed always changes OSPF cost automatically
- Declare success from a committed cost value without testing path changes
Explanation
Correct Answer
B:Shortest path is based on sum of relevant costs.
Incorrect Answers
A:One-sided metric policy can cause inconsistent path computation.
C:Cost depends on configured and reference bandwidth behavior.
D:Configuration state alone is not proof of intended egress.
Question 124
A provider upgraded one core link from 10 Gbps to 100 Gbps yet OSPF continues to favor an older path; link costs appear equal. The objective is to validate controlled convergence. Which verification should be performed before approving the change?
- Check selected route and data-plane path after metric adjustment
- Assume higher interface speed always changes OSPF cost automatically
- Choose the route solely because its last hop has the fastest port
- Change reference bandwidth on one router without assessing the topology
Explanation
Correct Answer
A:A new cost setting needs forwarding confirmation.
Incorrect Answers
B:Cost depends on configured and reference bandwidth behavior.
C:The complete path cost can differ from its final hop.
D:One-sided metric policy can cause inconsistent path computation.
Question 125
A provider upgraded one core link from 10 Gbps to 100 Gbps yet OSPF continues to favor an older path; link costs appear equal. Two objectives apply: (1) review actual interface costs; and (2) compute total path cost. Which TWO controls together satisfy the requirements? Choose TWO.
- Choose the route solely because its last hop has the fastest port
- Inspect OSPF effective costs on all competing paths
- Evaluate cumulative link costs rather than one interface alone
- Assume higher interface speed always changes OSPF cost automatically
- Change reference bandwidth on one router without assessing the topology
Explanation
Correct Answers
B:SPF selects using link-state topology and path cost.
C:Shortest path is based on sum of relevant costs.
Incorrect Answers
A:The complete path cost can differ from its final hop.
D:Cost depends on configured and reference bandwidth behavior.
E:One-sided metric policy can cause inconsistent path computation.
Question 126
A provider upgraded one core link from 10 Gbps to 100 Gbps yet OSPF continues to favor an older path; link costs appear equal. Three objectives apply: (1) review actual interface costs; (2) compute total path cost; and (3) validate controlled convergence. Which THREE controls together satisfy the requirements? Choose THREE.
- Choose the route solely because its last hop has the fastest port
- Inspect OSPF effective costs on all competing paths
- Check selected route and data-plane path after metric adjustment
- Evaluate cumulative link costs rather than one interface alone
- Change reference bandwidth on one router without assessing the topology
- Declare success from a committed cost value without testing path changes
Explanation
Correct Answers
B:SPF selects using link-state topology and path cost.
C:A new cost setting needs forwarding confirmation.
D:Shortest path is based on sum of relevant costs.
Incorrect Answers
A:The complete path cost can differ from its final hop.
E:One-sided metric policy can cause inconsistent path computation.
F:Configuration state alone is not proof of intended egress.
Question 127
Path engineering review shows bandwidth upgrades did not change OSPF path selection and one router has different reference bandwidth settings. Independently, the review flags the potentially unsafe practice “Assume higher interface speed always changes OSPF cost automatically”. Which inspection best evaluates that practice?
- Change reference bandwidth on one router without assessing the topology
- Compare complete SPF cost to each candidate destination
- Compare OSPF interface cost output on both paths
- Inspect selected OSPF route and actual outgoing interface
Explanation
Correct Answer
C:Cost depends on configured and reference bandwidth behavior. SPF selects using link-state topology and path cost.
Incorrect Answers
A:One-sided metric policy can cause inconsistent path computation.
B:Shortest path is based on sum of relevant costs.
D:A new cost setting needs forwarding confirmation.
Question 128
Path engineering review shows bandwidth upgrades did not change OSPF path selection and one router has different reference bandwidth settings. Independently, the review flags the potentially unsafe practice “Change reference bandwidth on one router without assessing the topology”. Which evidence most directly tests the flagged assumption?
- Choose the route solely because its last hop has the fastest port
- Compare OSPF interface cost output on both paths
- Compare OSPF reference bandwidth settings across devices
- Inspect selected OSPF route and actual outgoing interface
Explanation
Correct Answer
C:One-sided metric policy can cause inconsistent path computation. Inconsistent reference bandwidth can produce asymmetric path preferences.
Incorrect Answers
A:The complete path cost can differ from its final hop.
B:SPF selects using link-state topology and path cost.
D:A new cost setting needs forwarding confirmation.
Question 129
Path engineering review shows bandwidth upgrades did not change OSPF path selection and one router has different reference bandwidth settings. Independently, the review flags the potentially unsafe practice “Choose the route solely because its last hop has the fastest port”. Which diagnostic check tests this potentially unsafe choice?
- Compare OSPF interface cost output on both paths
- Declare success from a committed cost value without testing path changes
- Compare OSPF reference bandwidth settings across devices
- Compare complete SPF cost to each candidate destination
Explanation
Correct Answer
D:The complete path cost can differ from its final hop. Shortest path is based on sum of relevant costs.
Incorrect Answers
A:SPF selects using link-state topology and path cost.
B:Configuration state alone is not proof of intended egress.
C:Inconsistent reference bandwidth can produce asymmetric path preferences.
Question 130
Path engineering review shows bandwidth upgrades did not change OSPF path selection and one router has different reference bandwidth settings. Independently, the review flags the potentially unsafe practice “Declare success from a committed cost value without testing path changes”. Which validation addresses the risk without assuming a particular cause?
- Inspect selected OSPF route and actual outgoing interface
- Compare complete SPF cost to each candidate destination
- Change reference bandwidth on one router without assessing the topology
- Compare OSPF interface cost output on both paths
Explanation
Correct Answer
A:Configuration state alone is not proof of intended egress. A new cost setting needs forwarding confirmation.
Incorrect Answers
B:Shortest path is based on sum of relevant costs.
C:One-sided metric policy can cause inconsistent path computation.
D:SPF selects using link-state topology and path cost.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests