Juniper JN0-364 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-364 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-364  Premium File
$54.99
$49.99

JN0-364 Premium File

  • Premium File: 69 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-364 Premium File

Juniper JN0-364  Premium File
  • Premium File: 69 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-364 Practice Test 59

Question 580

The primary Routing Engine reboots; interfaces stay Up but some bridge learning or routing protocols briefly interrupt service. Independently, the review flags the potentially unsafe practice “Declare GRES and NSB verified because a command returned success”. Which validation addresses the risk without assuming a particular cause?

  1. Compare packet loss and control protocol state through RE change
  2. Force switchover while backup RE reports not ready
  3. Inspect bridging state and NSB operational support
  4. Inspect graceful-switchover readiness and RE roles

Explanation

Correct Answer

A:

Control-plane acknowledgment is not user-traffic evidence. Production continuity requires packet-level observation across both functions.

Incorrect Answers

B:

Backup readiness affects switchover outcome.

C:

NSB targets Layer 2 state continuity on supported platforms.

D:

GRES supports RE transition while limiting forwarding disruption.

Question 581

Two OSPF routers share a provider core path where physical optics remain lit after a remote forwarding fault. The objective is to associate BFD with neighbor. Which Junos configuration or design action best satisfies the objective?

  1. Assume one fixed submillisecond failure timeout is supported on every platform
  2. Treat physical link Up as proof BFD is exchanging control packets
  3. Declare service recovered because a BFD log says Down
  4. Configure supported BFD monitoring for the intended routing adjacency

Explanation

Correct Answer

D:

BFD detects forwarding-path failures rapidly for associated protocols.

Incorrect Answers

A:

Platform and session configuration constrain detection speed.

B:

Physical state alone cannot validate BFD liveness.

C:

Detection alone does not establish a new valid forwarding path.

Question 582

Two OSPF routers share a provider core path where physical optics remain lit after a remote forwarding fault. The objective is to negotiate detection intervals. Which operational choice should be prioritized in this design?

  1. Review minimum transmit and receive intervals and detection multiplier
  2. Declare service recovered because a BFD log says Down
  3. Enable BFD on an unrelated loopback and assume the failed neighbor is monitored
  4. Treat physical link Up as proof BFD is exchanging control packets

Explanation

Correct Answer

A:

BFD detect time depends on negotiated session parameters.

Incorrect Answers

B:

Detection alone does not establish a new valid forwarding path.

C:

BFD must operate for the targeted adjacency.

D:

Physical state alone cannot validate BFD liveness.

Question 583

Two OSPF routers share a provider core path where physical optics remain lit after a remote forwarding fault. The objective is to verify bidirectional session state. Which routing or switching control best fits the requirement?

  1. Declare service recovered because a BFD log says Down
  2. Assume one fixed submillisecond failure timeout is supported on every platform
  3. Confirm BFD reaches Up and detects both directions of forwarding
  4. Enable BFD on an unrelated loopback and assume the failed neighbor is monitored

Explanation

Correct Answer

C:

A configured BFD stanza does not prove a live session.

Incorrect Answers

A:

Detection alone does not establish a new valid forwarding path.

B:

Platform and session configuration constrain detection speed.

D:

BFD must operate for the targeted adjacency.

Question 584

Two OSPF routers share a provider core path where physical optics remain lit after a remote forwarding fault. The objective is to validate protocol reaction. Which verification should be performed before approving the change?

  1. Assume one fixed submillisecond failure timeout is supported on every platform
  2. Enable BFD on an unrelated loopback and assume the failed neighbor is monitored
  3. Treat physical link Up as proof BFD is exchanging control packets
  4. Test that a BFD Down event causes intended routing neighbor or path reaction

Explanation

Correct Answer

D:

Fast detection matters only if the routing protocol responds.

Incorrect Answers

A:

Platform and session configuration constrain detection speed.

B:

BFD must operate for the targeted adjacency.

C:

Physical state alone cannot validate BFD liveness.

Question 585

Two OSPF routers share a provider core path where physical optics remain lit after a remote forwarding fault. Two objectives apply: (1) associate BFD with neighbor; and (2) verify bidirectional session state. Which TWO controls together satisfy the requirements? Choose TWO.

  1. Confirm BFD reaches Up and detects both directions of forwarding
  2. Configure supported BFD monitoring for the intended routing adjacency
  3. Assume one fixed submillisecond failure timeout is supported on every platform
  4. Treat physical link Up as proof BFD is exchanging control packets
  5. Enable BFD on an unrelated loopback and assume the failed neighbor is monitored

Explanation

Correct Answers

A:

A configured BFD stanza does not prove a live session.

B:

BFD detects forwarding-path failures rapidly for associated protocols.

Incorrect Answers

C:

Platform and session configuration constrain detection speed.

D:

Physical state alone cannot validate BFD liveness.

E:

BFD must operate for the targeted adjacency.

Question 586

Two OSPF routers share a provider core path where physical optics remain lit after a remote forwarding fault. Three objectives apply: (1) negotiate detection intervals; (2) verify bidirectional session state; and (3) validate protocol reaction. Which THREE controls together satisfy the requirements? Choose THREE.

  1. Enable BFD on an unrelated loopback and assume the failed neighbor is monitored
  2. Confirm BFD reaches Up and detects both directions of forwarding
  3. Treat physical link Up as proof BFD is exchanging control packets
  4. Test that a BFD Down event causes intended routing neighbor or path reaction
  5. Assume one fixed submillisecond failure timeout is supported on every platform
  6. Review minimum transmit and receive intervals and detection multiplier

Explanation

Correct Answers

B:

A configured BFD stanza does not prove a live session.

D:

Fast detection matters only if the routing protocol responds.

F:

BFD detect time depends on negotiated session parameters.

Incorrect Answers

A:

BFD must operate for the targeted adjacency.

C:

Physical state alone cannot validate BFD liveness.

E:

Platform and session configuration constrain detection speed.

Question 587

Traffic blackholes for too long before IGP reconverges and BFD sessions show mismatched transmit and detect parameters. Independently, the review flags the potentially unsafe practice “Enable BFD on an unrelated loopback and assume the failed neighbor is monitored”. Which inspection best evaluates that practice?

  1. Assume one fixed submillisecond failure timeout is supported on every platform
  2. Compare BFD failure event with route and next-hop convergence
  3. Inspect BFD session association with the routing peer
  4. Inspect BFD session state and receive counters

Explanation

Correct Answer

C:

BFD must operate for the targeted adjacency. BFD detects forwarding-path failures rapidly for associated protocols.

Incorrect Answers

A:

Platform and session configuration constrain detection speed.

B:

Fast detection matters only if the routing protocol responds.

D:

A configured BFD stanza does not prove a live session.

Question 588

Traffic blackholes for too long before IGP reconverges and BFD sessions show mismatched transmit and detect parameters. Independently, the review flags the potentially unsafe practice “Assume one fixed submillisecond failure timeout is supported on every platform”. Which evidence most directly tests the flagged assumption?

  1. Compare BFD failure event with route and next-hop convergence
  2. Enable BFD on an unrelated loopback and assume the failed neighbor is monitored
  3. Inspect negotiated BFD interval and multiplier
  4. Inspect BFD session state and receive counters

Explanation

Correct Answer

C:

Platform and session configuration constrain detection speed. BFD detect time depends on negotiated session parameters.

Incorrect Answers

A:

Fast detection matters only if the routing protocol responds.

B:

BFD must operate for the targeted adjacency.

D:

A configured BFD stanza does not prove a live session.

Question 589

Traffic blackholes for too long before IGP reconverges and BFD sessions show mismatched transmit and detect parameters. Independently, the review flags the potentially unsafe practice “Treat physical link Up as proof BFD is exchanging control packets”. Which diagnostic check tests this potentially unsafe choice?

  1. Compare BFD failure event with route and next-hop convergence
  2. Assume one fixed submillisecond failure timeout is supported on every platform
  3. Inspect BFD session association with the routing peer
  4. Inspect BFD session state and receive counters

Explanation

Correct Answer

D:

Physical state alone cannot validate BFD liveness. A configured BFD stanza does not prove a live session.

Incorrect Answers

A:

Fast detection matters only if the routing protocol responds.

B:

Platform and session configuration constrain detection speed.

C:

BFD detects forwarding-path failures rapidly for associated protocols.

Question 590

Traffic blackholes for too long before IGP reconverges and BFD sessions show mismatched transmit and detect parameters. Independently, the review flags the potentially unsafe practice “Declare service recovered because a BFD log says Down”. Which validation addresses the risk without assuming a particular cause?

  1. Inspect BFD session state and receive counters
  2. Enable BFD on an unrelated loopback and assume the failed neighbor is monitored
  3. Inspect negotiated BFD interval and multiplier
  4. Compare BFD failure event with route and next-hop convergence

Explanation

Correct Answer

D:

Detection alone does not establish a new valid forwarding path. Fast detection matters only if the routing protocol responds.

Incorrect Answers

A:

A configured BFD stanza does not prove a live session.

B:

BFD must operate for the targeted adjacency.

C:

BFD detect time depends on negotiated session parameters.

Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.