100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 300
Which suggested shortcut would be especially unsafe for this exact situation? A service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff.
- Version-control MSTP name, revision and VLAN mapping as one change unit.
- Keep explicit root priority policy and validate elections after device replacement.
- Test each critical VLAN's root bridge and forwarding path after VSTP updates.
- Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated.
Explanation
Correct Answer
D:The tempting alternative fails because Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context. The supported action is to design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
Incorrect Answers
A:That prevention measure relates to an uplink becomes a region boundary unexpectedly after an administrator changes an MSTP configuration name on only one switch.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree.; it is not the unsafe shortcut described here.
Question 301
Which suggested shortcut would be especially unsafe for this exact situation? Two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules.
- Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
- Use only the MED field as guaranteed proof of the selected route regardless of preceding BGP attributes.
- Track every BGP advertise-inactive exception and test cross-protocol route selection.
- Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
Explanation
Correct Answer
B:The tempting alternative fails because MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions. The supported action is to read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence.
Incorrect Answers
A:That prevention measure relates to a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a BGP export policy advertises a prefix that exists only as an inactive local candidate, despite an expectation of default active-only behavior.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor.; it is not the unsafe shortcut described here.
Question 302
To prevent recurrence of this precise networking failure, which practice should be adopted? Two newly deployed distribution switches report identical OSPF router IDs, causing inconsistent LSAs in the area.
- Reserve router IDs from a centrally managed inventory before zero-touch provisioning.
- Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance.
- Document expected external metrics and run primary/backup failover tests during policy changes.
- Validate active logical-interface mappings and IPv6 adjacency as part of change acceptance.
Explanation
Correct Answer
A:Reserve router IDs from a centrally managed inventory before zero-touch provisioning. This guards against OSPF identifies routers by unique router ID; collisions can destabilize LSDB and adjacency behavior.
Incorrect Answers
B:“Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance” belongs to a separate Interior Gateway Protocols (IGPs) issue: OSPFv3 peering comes up but the desired IPv6 loopback is not in the routing database after a rollout. It does not explain the condition tested here.
C:“Document expected external metrics and run primary/backup failover tests during policy changes” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.
D:“Validate active logical-interface mappings and IPv6 adjacency as part of change acceptance” belongs to a separate Interior Gateway Protocols (IGPs) issue: a new IPv6 peering uses OSPFv3 on a retired VLAN unit rather than the active routed transit interface. It does not explain the condition tested here.
Question 303
Select THREE complementary corrective, verification, or preventive controls for this scenario: A branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit.
- Review external metric type and value at the originator, then apply the documented traffic-engineering policy.
- The preferred primary route wins when healthy and the backup becomes active on a controlled failure.
- Disable the MTU check indefinitely without identifying why adjacent links differ.
- Increase every external metric blindly without checking which path should win.
- Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy.
- Document expected external metrics and run primary/backup failover tests during policy changes.
Explanation
Correct Answers
A:Correction: OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior.
B:Confirmation: Review external metric type and value at the originator, then apply the documented traffic-engineering policy.
F:Prevention of recurrence: OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior.
Incorrect Answers
C:“Disable the MTU check indefinitely without identifying why adjacent links differ” is an unsafe response to a different problem: a core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs. It is not a valid fix here.
D:“Increase every external metric blindly without checking which path should win” does not address OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior.
E:“Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy” is an unsafe response to a different problem: an IPv6 branch outage is misdiagnosed using only IPv4 pings, despite OSPFv3 neighbors using IPv6 link-local messaging. It is not a valid fix here.
Question 304
A Junos enterprise team investigates this incident: A campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. Which technical explanation most directly identifies the cause or design principle?
- EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set.
- EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.
- EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence.
- VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic.
Explanation
Correct Answer
D:VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic. The appropriate response is to compare VLAN-to-VNI and bridge-domain assignments on all leafs and correct them against the approved tenant map.
Incorrect Answers
A:“EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set” belongs to a separate EVPN issue: a VNI is active on two leafs but unknown-unicast or broadcast replication never reaches the remote side. It does not explain the condition tested here.
B:“EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops” belongs to a separate EVPN issue: a dual-attached Ethernet segment experiences persistent duplicates during link recovery because multihoming election or ESI state differs. It does not explain the condition tested here.
C:“EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence” belongs to a separate EVPN issue: a multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. It does not explain the condition tested here.
Question 305
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: Two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules.
- Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence.
- Point to a successful IPv4 traceroute as sufficient proof an IPv6 BGP next hop resolves.
- Use only the MED field as guaranteed proof of the selected route regardless of preceding BGP attributes.
- Assume successful inet IPv4 routes imply that IPv6 NLRI is already negotiated.
- The chosen best path follows the documented attribute ordering rather than a single observed MED value.
Explanation
Correct Answers
A:Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence. This addresses the dependency that MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions.
E:The chosen best path follows the documented attribute ordering rather than a single observed MED value. The specific steps required are to read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence.
Incorrect Answers
B:“Point to a successful IPv4 traceroute as sufficient proof an IPv6 BGP next hop resolves” is an unsafe response to a different problem: an IPv6 transit prefix is hidden because its next-hop address is absent from the correct IPv6 routing table. It is not a valid fix here.
C:“Use only the MED field as guaranteed proof of the selected route regardless of preceding BGP attributes” does not address MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions.
D:“Assume successful inet IPv4 routes imply that IPv6 NLRI is already negotiated” is an unsafe response to a different problem: a campus router's BGP IPv6 session is Established yet peers advertise only inet unicast family routes. It is not a valid fix here.
Question 306
A Junos enterprise team investigates this incident: An enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path. Which technical explanation most directly identifies the cause or design principle?
- The default BGP AS-path loop check rejects routes containing the local autonomous system to prevent loops.
- BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers.
- Routing-policy term order and terminal actions determine whether later conditions are evaluated.
- BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
Explanation
Correct Answer
B:BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers. The appropriate response is to inspect per-route local preferences and import policy; set the intended exit's LOCAL_PREF consistently.
Incorrect Answers
A:“The default BGP AS-path loop check rejects routes containing the local autonomous system to prevent loops” belongs to a separate Border Gateway Protocol (BGP) issue: a carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path. It does not explain the condition tested here.
C:“Routing-policy term order and terminal actions determine whether later conditions are evaluated” belongs to a separate Border Gateway Protocol (BGP) issue: a route with a permissive policy term is accepted before a later deny term can block it. It does not explain the condition tested here.
D:“BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately” belongs to a separate Border Gateway Protocol (BGP) issue: a prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor. It does not explain the condition tested here.
Question 307
To prevent recurrence of this precise networking failure, which practice should be adopted? An EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior.
- Keep route-type purpose and acceptance checks in EVPN troubleshooting runbooks.
- Test multihoming election and per-VLAN failover after attaching new dual-homed devices.
- Include encapsulation headroom and path MTU tests in EVPN-VXLAN design validation.
- Include underlay loopback reachability and MTU checks in VXLAN overlay deployment QA.
Explanation
Correct Answer
B:Test multihoming election and per-VLAN failover after attaching new dual-homed devices. This guards against EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.
Incorrect Answers
A:“Keep route-type purpose and acceptance checks in EVPN troubleshooting runbooks” belongs to a separate EVPN issue: a fabric advertises Type 3 routes and claims this proves specific remote host MACs are reachable. It does not explain the condition tested here.
C:“Include encapsulation headroom and path MTU tests in EVPN-VXLAN design validation” belongs to a separate EVPN issue: an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. It does not explain the condition tested here.
D:“Include underlay loopback reachability and MTU checks in VXLAN overlay deployment QA” belongs to a separate EVPN issue: a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback. It does not explain the condition tested here.
Question 308
A Junos enterprise team investigates this incident: A campus summarization change hides a needed subnet because the configured address range omits it. Which technical explanation most directly identifies the cause or design principle?
- Unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability.
- IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges.
- Area summarization scope must correctly cover the intended component networks; the wrong range can suppress or misrepresent reachability.
- Routing-policy match criteria must align with the source route type and the intended OSPF export behavior.
Explanation
Correct Answer
C:Area summarization scope must correctly cover the intended component networks; the wrong range can suppress or misrepresent reachability. The appropriate response is to verify the aggregate range, component prefixes and ABR advertisements, then correct the summary policy to the approved address plan.
Incorrect Answers
A:“Unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability” belongs to a separate Interior Gateway Protocols (IGPs) issue: a redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local. It does not explain the condition tested here.
B:“IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6 branch outage is misdiagnosed using only IPv4 pings, despite OSPFv3 neighbors using IPv6 link-local messaging. It does not explain the condition tested here.
D:“Routing-policy match criteria must align with the source route type and the intended OSPF export behavior” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated. It does not explain the condition tested here.
Question 309
Which suggested shortcut would be especially unsafe for this exact situation? A new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address.
- Validate all required BGP address families during dual-stack peer commissioning.
- Lower AS-path length without fixing the unreachable BGP next-hop address.
- Test expected best-path behavior before modifying LOCAL_PREF across internal peers.
- Monitor AS-path anomalies and validate inter-AS topology changes before enabling export.
Explanation
Correct Answer
B:The tempting alternative fails because BGP route selection first requires the BGP next hop to resolve through the appropriate routing table. The supported action is to restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.
Incorrect Answers
A:That prevention measure relates to BGP peers exchange IPv4 NLRI correctly but a planned IPv6 customer route never appears in inet6.0.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path.; it is not the unsafe shortcut described here.
Question 310
A Junos enterprise team investigates this incident: A campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. Which technical explanation most directly identifies the cause or design principle?
- Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles.
- Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
- MVRP registrations can persist where membership state or participation has not been updated consistently.
- MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.
Explanation
Correct Answer
C:MVRP registrations can persist where membership state or participation has not been updated consistently. The appropriate response is to inspect registration state and remove stale VLAN membership while preserving necessary registrations.
Incorrect Answers
A:“Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. It does not explain the condition tested here.
B:“Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns” belongs to a separate Ethernet Switching and Spanning Tree issue: a network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN. It does not explain the condition tested here.
D:“MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests