Palo Alto Networks NGFW-Engineer Exam Dumps, Practice Test Questions

100% Latest & Updated Palo Alto Networks NGFW-Engineer Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Palo Alto Networks NGFW-Engineer  Premium File
$54.99
$49.99

NGFW-Engineer Premium File

  • Premium File: 143 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

NGFW-Engineer Premium File

Palo Alto Networks NGFW-Engineer  Premium File
  • Premium File: 143 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Palo Alto Networks NGFW-Engineer Practice Test 8

Question 70

A branch firewall connects to a switch pair using two Ethernet ports that should behave as one logical uplink. After the change, which observation would most directly prove the intended behavior?

  1. Inspect aggregate interface status, LACP member state, and traffic distribution
  2. Inspect the actual forwarding lookup for the application's destination prefix
  3. Compare the connected route and ARP neighbor entries for the expected LAN
  4. Confirm each VLAN tag resolves to its own configured IP gateway and zone

Explanation

Correct Answer

A:

Inspect aggregate interface status, LACP member state, and traffic distribution. A link-up on just one member does not prove a healthy bundle.

Incorrect Answers

B:

Inspect the actual forwarding lookup for the application's destination prefix. This proves which of the two uplinks a new session will use. The relevant evidence here is “Inspect aggregate interface status, LACP member state, and traffic distribution”.

C:

Compare the connected route and ARP neighbor entries for the expected LAN. These distinguish addressing or adjacency faults from an application-layer problem. Its effect is distinct from the intended configuration outcome here. The relevant evidence here is “Inspect aggregate interface status, LACP member state, and traffic distribution”.

D:

This demonstrates that tagged traffic is not accidentally sharing the wrong routed tenant context. That observation would not by itself verify this particular change.

Question 71

A branch firewall connects to a switch pair using two Ethernet ports that should behave as one logical uplink. During validation, the following problem is reported: The peers will not form the intended consistent link aggregation. Which defect or mistaken assumption most directly accounts for this result?

  1. A mismatched subnet mask between the gateway and connected clients
  2. Configuring both tenant gateway addresses on one untagged parent interface
  3. Import policy silently denying the exact prefix that the application requires
  4. Configuring LACP on the firewall while the switch ports remain independent non-LACP trunks

Explanation

Correct Answer

D:

Configuring LACP on the firewall while the switch ports remain independent non-LACP trunks. The peers will not form the intended consistent link aggregation.

Incorrect Answers

A:

Hosts may ARP or route to the wrong destination because the common network boundary differs. It addresses a different part of the firewall deployment, not the failure described. The issue evaluated here is “Configuring LACP on the firewall while the switch ports remain independent non-LACP trunks”.

B:

Configuring both tenant gateway addresses on one untagged parent interface. The design no longer separates the tenants by their trunk tags. The issue evaluated here is “Configuring LACP on the firewall while the switch ports remain independent non-LACP trunks”.

C:

Import policy silently denying the exact prefix that the application requires. The remote network is never installed despite healthy BGP peering. This action would leave the decisive condition in the case unchanged.

Question 72

A branch firewall connects to a switch pair using two Ethernet ports that should behave as one logical uplink. Before releasing the change, which safeguard most directly reduces the associated operational or security risk?

  1. Define separate security zones and narrowly scoped interzone access for the subnets
  2. Coordinate member changes with the switch team and avoid treating AE as a substitute for downstream path diversity
  3. Set and test a recovery hold-down policy suitable for the site
  4. Allow only documented VLAN tags across the inline pair

Explanation

Correct Answer

B:

Coordinate member changes with the switch team and avoid treating AE as a substitute for downstream path diversity. Bundling improves link resilience only within the actual topology.

Incorrect Answers

A:

Define separate security zones and narrowly scoped interzone access for the subnets. Routing reachability alone should not permit every application between segments. That protection is useful, but it does not control the risk introduced by this change. The relevant safeguard here is “Coordinate member changes with the switch team and avoid treating AE as a substitute for downstream path diversity”.

C:

Set and test a recovery hold-down policy suitable for the site. Rapidly changing link states should not cause repeated HA role oscillation. Its effect is distinct from the intended configuration outcome here. The relevant safeguard here is “Coordinate member changes with the switch team and avoid treating AE as a substitute for downstream path diversity”.

D:

Allow only documented VLAN tags across the inline pair. Unrestricted tag handling may expose unintended segments to the connected path. That feature does not establish the specific result needed in this situation.

Question 73

Two 10 GbE firewall ports must provide a single tagged tenant uplink and retain per-VLAN zones. What is the most appropriate next engineering action for this situation?

  1. Inspect BGP import filtering and route-selection outcomes for the specific prefix
  2. Configure the permitted Layer 2 subinterfaces with the matching VLAN tags
  3. Create tagged subinterfaces on the Aggregate Ethernet parent, not on independent members
  4. Configure the supported OSPF routing instance, interface, area, and neighbor parameters

Explanation

Correct Answer

C:

Create tagged subinterfaces on the Aggregate Ethernet parent, not on independent members. Logical VLAN configuration belongs on the aggregate interface carrying the bundled trunk.

Incorrect Answers

A:

Inspect BGP import filtering and route-selection outcomes for the specific prefix. A live session can still reject a route under configured policy. This case instead requires “Create tagged subinterfaces on the Aggregate Ethernet parent, not on independent members”.

B:

Tagged Layer 2 subinterfaces preserve segmentation when multiple VLANs traverse one physical port. Its effect is distinct from the intended configuration outcome here.

D:

Configure the supported OSPF routing instance, interface, area, and neighbor parameters. OSPF adjacency requires matching routing-protocol settings on the shared segment. The case depends on a different setting or test to meet its requirement.

Question 74

Two 10 GbE firewall ports must provide a single tagged tenant uplink and retain per-VLAN zones. After the change, which observation would most directly prove the intended behavior?

  1. Compare received and accepted BGP routes with installed forwarding entries
  2. Check VLAN tags on the AE subinterfaces and confirm all intended members are forwarding
  3. Inspect the ingress tag and egress forwarding result for the affected VLAN
  4. Capture VLAN tags and check the correct subinterface and zone handling of each test frame

Explanation

Correct Answer

B:

This proves the tenant trunks use the logical aggregate rather than mismatched individual ports.

Incorrect Answers

A:

Compare received and accepted BGP routes with installed forwarding entries. This isolates filtering or route selection from adjacency failure. That observation would not by itself verify this particular change.

C:

Inspect the ingress tag and egress forwarding result for the affected VLAN. A packet capture can isolate a VLAN membership failure from a security-policy denial. The relevant evidence here is “Check VLAN tags on the AE subinterfaces and confirm all intended members are forwarding”.

D:

Capture VLAN tags and check the correct subinterface and zone handling of each test frame. The tag and ingress subinterface show whether traffic stays in its planned segment. This does not show that the specified firewall path works as intended.

Question 75

Two 10 GbE firewall ports must provide a single tagged tenant uplink and retain per-VLAN zones. During validation, the following problem is reported: The logical aggregate will lack the expected VLAN endpoint configuration. Which defect or mistaken assumption most directly accounts for this result?

  1. Leaving tenant subinterfaces attached only to a physical member being moved into AE
  2. Applying a policy to the wrong routing instance or peer group
  3. Putting the two bridged ports into unrelated VLAN objects
  4. Reversing the expected external peer AS number in the BGP configuration

Explanation

Correct Answer

A:

Leaving tenant subinterfaces attached only to a physical member being moved into AE. The logical aggregate will lack the expected VLAN endpoint configuration.

Incorrect Answers

B:

Applying a policy to the wrong routing instance or peer group. The intended prefix's best-path decision remains unchanged. The observed failure here would remain unresolved by that step. The issue evaluated here is “Leaving tenant subinterfaces attached only to a physical member being moved into AE”.

C:

Putting the two bridged ports into unrelated VLAN objects. The ports then lack the intended common Layer 2 forwarding domain. This action would leave the decisive condition in the case unchanged.

D:

Reversing the expected external peer AS number in the BGP configuration. The session may fail to establish with the authorized router. It addresses a different part of the firewall deployment, not the failure described. The issue evaluated here is “Leaving tenant subinterfaces attached only to a physical member being moved into AE”.

Question 76

Two 10 GbE firewall ports must provide a single tagged tenant uplink and retain per-VLAN zones. Before releasing the change, which safeguard most directly reduces the associated operational or security risk?

  1. Test certificate trust and MFA fail-closed behavior for rejected users
  2. Stage the trunk change on one tested VLAN before expanding the allowed tag list
  3. Move the trunk in a controlled sequence with rollback for both switch and firewall
  4. Document underlay and overlay addresses so routes cannot recurse through the GRE tunnel

Explanation

Correct Answer

C:

Move the trunk in a controlled sequence with rollback for both switch and firewall. An incorrect member or subinterface migration can drop every tenant VLAN at once.

Incorrect Answers

A:

Test certificate trust and MFA fail-closed behavior for rejected users. Authentication failures must not silently fall back to weak access. Its effect is distinct from the intended configuration outcome here. The relevant safeguard here is “Move the trunk in a controlled sequence with rollback for both switch and firewall”.

B:

Stage the trunk change on one tested VLAN before expanding the allowed tag list. A narrow cutover limits disruption and unexpected cross-VLAN connectivity. That protection is useful, but it does not control the risk introduced by this change. The relevant safeguard here is “Move the trunk in a controlled sequence with rollback for both switch and firewall”.

D:

Document underlay and overlay addresses so routes cannot recurse through the GRE tunnel. Tunnel endpoints must remain reachable on the real transit network. That feature does not establish the specific result needed in this situation.

Question 77

A bundled uplink remains partially available after a switch-side port failure, but the team wants to know which physical member failed. What is the most appropriate next engineering action for this situation?

  1. Set the Layer 3 interface prefix and peer addressing to the actual supported /31 design
  2. Use documented route-selection policy such as BGP local preference where applicable
  3. Inspect BGP import filtering and route-selection outcomes for the specific prefix
  4. Inspect the Aggregate Ethernet member and LACP state on both peers

Explanation

Correct Answer

D:

Inspect the Aggregate Ethernet member and LACP state on both peers. Per-member state identifies degraded redundancy even if the logical aggregate stays up.

Incorrect Answers

A:

A /31 point-to-point link has two endpoint addresses and depends on matching configuration on both sides. This case instead requires “Inspect the Aggregate Ethernet member and LACP state on both peers”.

B:

Use documented route-selection policy such as BGP local preference where applicable. Route attributes can influence which valid BGP path the firewall chooses. That feature does not establish the specific result needed in this situation. This case instead requires “Inspect the Aggregate Ethernet member and LACP state on both peers”.

C:

Inspect BGP import filtering and route-selection outcomes for the specific prefix. A live session can still reject a route under configured policy. This action would leave the decisive condition in the case unchanged.

Question 78

A bundled uplink remains partially available after a switch-side port failure, but the team wants to know which physical member failed. After the change, which observation would most directly prove the intended behavior?

  1. Capture VLAN tags and check the correct subinterface and zone handling of each test frame
  2. Compare member operational state against the configured expected LACP bundle
  3. Check MAC learning and permitted traffic across the intended Layer 2 VLAN
  4. Inspect the ingress tag and egress forwarding result for the affected VLAN

Explanation

Correct Answer

B:

Compare member operational state against the configured expected LACP bundle. This distinguishes normal reduced capacity from an unjoined member.

Incorrect Answers

A:

Capture VLAN tags and check the correct subinterface and zone handling of each test frame. The tag and ingress subinterface show whether traffic stays in its planned segment. That feature does not establish the specific result needed in this situation.

C:

Forwarding between the bridged ports proves the VLAN path is present without an unintended routing hop. The relevant evidence here is “Compare member operational state against the configured expected LACP bundle”.

D:

Inspect the ingress tag and egress forwarding result for the affected VLAN. A packet capture can isolate a VLAN membership failure from a security-policy denial. This does not show that the specified firewall path works as intended.

Question 79

A bundled uplink remains partially available after a switch-side port failure, but the team wants to know which physical member failed. During validation, the following problem is reported: The bundle can pass traffic while a member is failed or suspended. Which defect or mistaken assumption most directly accounts for this result?

  1. Assuming aggregate interface up means every member port is forwarding
  2. Reversing the expected external peer AS number in the BGP configuration
  3. Changing a switch-facing firewall port to Layer 3 without configuring the required gateway design
  4. Configuring both tenant gateway addresses on one untagged parent interface

Explanation

Correct Answer

A:

Assuming aggregate interface up means every member port is forwarding. The bundle can pass traffic while a member is failed or suspended.

Incorrect Answers

B:

Reversing the expected external peer AS number in the BGP configuration. The session may fail to establish with the authorized router. The mismatch would persist because this choice targets another control point. The issue evaluated here is “Assuming aggregate interface up means every member port is forwarding”.

C:

Changing a switch-facing firewall port to Layer 3 without configuring the required gateway design. The cutover changes how frames are forwarded and can strand the original host subnet. The observed failure here would remain unresolved by that step.

D:

Configuring both tenant gateway addresses on one untagged parent interface. The design no longer separates the tenants by their trunk tags. It addresses a different part of the firewall deployment, not the failure described.

Question 80

A bundled uplink remains partially available after a switch-side port failure, but the team wants to know which physical member failed. Which TWO measures together provide a direct verification and a safe deployment control? Choose TWO.

  1. Capture VLAN tags and check the correct subinterface and zone handling of each test frame
  2. Compare member operational state against the configured expected LACP bundle
  3. Alert on member loss and evaluate application capacity under degraded bundle conditions
  4. Use explicit change review for reusable profiles used by multiple routing contexts
  5. Use explicit prefix filters and maximum-prefix safeguards on the peering

Explanation

Correct Answers

B:

Compare member operational state against the configured expected LACP bundle. This distinguishes normal reduced capacity from an unjoined member.

C:

Alert on member loss and evaluate application capacity under degraded bundle conditions. A surviving bundle may not have enough bandwidth for peak load.

Incorrect Answers

A:

Capture VLAN tags and check the correct subinterface and zone handling of each test frame. The tag and ingress subinterface show whether traffic stays in its planned segment. This case instead requires “Compare member operational state against the configured expected LACP bundle | Alert on member loss and evaluate application capacity under degraded bundle conditions”.

D:

Use explicit change review for reusable profiles used by multiple routing contexts. One profile update can alter many neighbors at once. Its effect is distinct from the intended configuration outcome here. This case instead requires “Compare member operational state against the configured expected LACP bundle | Alert on member loss and evaluate application capacity under degraded bundle conditions”.

E:

Use explicit prefix filters and maximum-prefix safeguards on the peering. An external session must not import uncontrolled routes into production. That feature does not establish the specific result needed in this situation. This case instead requires “Compare member operational state against the configured expected LACP bundle | Alert on member loss and evaluate application capacity under degraded bundle conditions”.

Palo Alto Networks Certified Next-Generation Firewall Engineer (NGFW-Engineer) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.