100% Latest & Updated Juniper JN0-364 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 390
An engineer checks only a single generic root and misses a VLAN-specific blocked port that causes customer symptoms. Independently, the review flags the potentially unsafe practice “Assume every ACX, MX, EX and QFX supports identical VSTP features”. Which validation addresses the risk without assuming a particular cause?
- Compare configured VSTP VLAN membership and service VLAN list
- Check supported features and operational VSTP state on the device
- Assume the root and blocked interfaces must be identical for every VSTP VLAN
- Inspect VLAN-specific path cost and bridge priority
Explanation
Correct Answer
B:Platform implementation can differ. Feature availability differs across device families.
Incorrect Answers
A:The relevant VLAN must participate in the configured tree.
C:Per-VLAN topology can select different ports.
D:A VLAN-specific problem may not justify a bridge-wide change.
Question 391
A customer access port should attach to an endpoint, but an unauthorized small switch starts sending BPDUs and threatens provider spanning-tree stability. The objective is to apply BPDU protection appropriately. Which Junos configuration or design action best satisfies the objective?
- Use BPDU protection on endpoint-facing ports where receiving BPDUs is forbidden
- Use root protection indiscriminately on every uplink toward the elected root
- Assume an Up interface means BPDUs are always received
- Re-enable blocked access ports without investigating recurring BPDUs
Explanation
Correct Answer
A:BPDU arrival on an edge port may indicate an unexpected bridge.
Incorrect Answers
B:Misplaced protection can block legitimate topology changes.
C:Physical link state does not confirm BPDU exchange.
D:Premature release can restore the loop threat.
Question 392
A customer access port should attach to an endpoint, but an unauthorized small switch starts sending BPDUs and threatens provider spanning-tree stability. The objective is to preserve intended root boundary. Which operational choice should be prioritized in this design?
- Assume an Up interface means BPDUs are always received
- Re-enable blocked access ports without investigating recurring BPDUs
- Configure root protection on suitable downstream-facing bridge connections
- Disable BPDU protection on all user-facing ports to hide alerts
Explanation
Correct Answer
C:Root protection discourages an unexpected downstream root takeover.
Incorrect Answers
A:Physical link state does not confirm BPDU exchange.
B:Premature release can restore the loop threat.
D:Ignoring unauthorized BPDUs can allow topology manipulation.
Question 393
A customer access port should attach to an endpoint, but an unauthorized small switch starts sending BPDUs and threatens provider spanning-tree stability. The objective is to identify loop protection role. Which routing or switching control best fits the requirement?
- Apply loop protection to designated blocking scenarios where missing BPDUs could cause loops
- Disable BPDU protection on all user-facing ports to hide alerts
- Use root protection indiscriminately on every uplink toward the elected root
- Re-enable blocked access ports without investigating recurring BPDUs
Explanation
Correct Answer
A:Loop protection helps prevent erroneous forwarding after control-plane loss.
Incorrect Answers
B:Ignoring unauthorized BPDUs can allow topology manipulation.
C:Misplaced protection can block legitimate topology changes.
D:Premature release can restore the loop threat.
Question 394
A customer access port should attach to an endpoint, but an unauthorized small switch starts sending BPDUs and threatens provider spanning-tree stability. The objective is to verify controlled recovery. Which verification should be performed before approving the change?
- Disable BPDU protection on all user-facing ports to hide alerts
- Test unauthorized BPDU and fault recovery under the site's approved procedure
- Assume an Up interface means BPDUs are always received
- Use root protection indiscriminately on every uplink toward the elected root
Explanation
Correct Answer
B:Protection should contain the risk and have a defined restoration path.
Incorrect Answers
A:Ignoring unauthorized BPDUs can allow topology manipulation.
C:Physical link state does not confirm BPDU exchange.
D:Misplaced protection can block legitimate topology changes.
Question 395
A customer access port should attach to an endpoint, but an unauthorized small switch starts sending BPDUs and threatens provider spanning-tree stability. Two objectives apply: (1) preserve intended root boundary; and (2) verify controlled recovery. Which TWO controls together satisfy the requirements? Choose TWO.
- Configure root protection on suitable downstream-facing bridge connections
- Test unauthorized BPDU and fault recovery under the site's approved procedure
- Re-enable blocked access ports without investigating recurring BPDUs
- Assume an Up interface means BPDUs are always received
- Use root protection indiscriminately on every uplink toward the elected root
Explanation
Correct Answers
A:Root protection discourages an unexpected downstream root takeover.
B:Protection should contain the risk and have a defined restoration path.
Incorrect Answers
C:Premature release can restore the loop threat.
D:Physical link state does not confirm BPDU exchange.
E:Misplaced protection can block legitimate topology changes.
Question 396
A customer access port should attach to an endpoint, but an unauthorized small switch starts sending BPDUs and threatens provider spanning-tree stability. Three objectives apply: (1) apply BPDU protection appropriately; (2) identify loop protection role; and (3) verify controlled recovery. Which THREE controls together satisfy the requirements? Choose THREE.
- Apply loop protection to designated blocking scenarios where missing BPDUs could cause loops
- Test unauthorized BPDU and fault recovery under the site's approved procedure
- Disable BPDU protection on all user-facing ports to hide alerts
- Use BPDU protection on endpoint-facing ports where receiving BPDUs is forbidden
- Re-enable blocked access ports without investigating recurring BPDUs
- Assume an Up interface means BPDUs are always received
Explanation
Correct Answers
A:Loop protection helps prevent erroneous forwarding after control-plane loss.
B:Protection should contain the risk and have a defined restoration path.
D:BPDU arrival on an edge port may indicate an unexpected bridge.
Incorrect Answers
C:Ignoring unauthorized BPDUs can allow topology manipulation.
E:Premature release can restore the loop threat.
F:Physical link state does not confirm BPDU exchange.
Question 397
A maintenance patch accidentally loops an access segment and repeated topology changes appear in protection counters. Independently, the review flags the potentially unsafe practice “Disable BPDU protection on all user-facing ports to hide alerts”. Which inspection best evaluates that practice?
- Inspect BPDU-protection action and event counters
- Use root protection indiscriminately on every uplink toward the elected root
- Inspect protection alarm cause and recovery behavior
- Review BPDU receive counters and loop-protection state
Explanation
Correct Answer
A:Ignoring unauthorized BPDUs can allow topology manipulation. BPDU arrival on an edge port may indicate an unexpected bridge.
Incorrect Answers
B:Misplaced protection can block legitimate topology changes.
C:Protection should contain the risk and have a defined restoration path.
D:Loop protection helps prevent erroneous forwarding after control-plane loss.
Question 398
A maintenance patch accidentally loops an access segment and repeated topology changes appear in protection counters. Independently, the review flags the potentially unsafe practice “Use root protection indiscriminately on every uplink toward the elected root”. Which evidence most directly tests the flagged assumption?
- Inspect BPDU-protection action and event counters
- Review BPDU receive counters and loop-protection state
- Re-enable blocked access ports without investigating recurring BPDUs
- Inspect protection placement relative to expected root path
Explanation
Correct Answer
D:Misplaced protection can block legitimate topology changes. Root protection discourages an unexpected downstream root takeover.
Incorrect Answers
A:BPDU arrival on an edge port may indicate an unexpected bridge.
B:Loop protection helps prevent erroneous forwarding after control-plane loss.
C:Premature release can restore the loop threat.
Question 399
A maintenance patch accidentally loops an access segment and repeated topology changes appear in protection counters. Independently, the review flags the potentially unsafe practice “Assume an Up interface means BPDUs are always received”. Which diagnostic check tests this potentially unsafe choice?
- Review BPDU receive counters and loop-protection state
- Inspect BPDU-protection action and event counters
- Re-enable blocked access ports without investigating recurring BPDUs
- Inspect protection placement relative to expected root path
Explanation
Correct Answer
A:Physical link state does not confirm BPDU exchange. Loop protection helps prevent erroneous forwarding after control-plane loss.
Incorrect Answers
B:BPDU arrival on an edge port may indicate an unexpected bridge.
C:Premature release can restore the loop threat.
D:Root protection discourages an unexpected downstream root takeover.
Question 400
A maintenance patch accidentally loops an access segment and repeated topology changes appear in protection counters. Independently, the review flags the potentially unsafe practice “Re-enable blocked access ports without investigating recurring BPDUs”. Which validation addresses the risk without assuming a particular cause?
- Inspect protection alarm cause and recovery behavior
- Review BPDU receive counters and loop-protection state
- Disable BPDU protection on all user-facing ports to hide alerts
- Inspect protection placement relative to expected root path
Explanation
Correct Answer
A:Premature release can restore the loop threat. Protection should contain the risk and have a defined restoration path.
Incorrect Answers
B:Loop protection helps prevent erroneous forwarding after control-plane loss.
C:Ignoring unauthorized BPDUs can allow topology manipulation.
D:Root protection discourages an unexpected downstream root takeover.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests