Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 100

Question 990

A Junos enterprise team investigates this incident: A fabric advertises Type 3 routes and claims this proves specific remote host MACs are reachable. Which technical explanation most directly identifies the cause or design principle?

  1. VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic.
  2. EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.
  3. EVPN route types carry different information: Type 1 Ethernet auto-discovery, Type 2 MAC/IP, Type 3 inclusive multicast.
  4. EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence.

Explanation

Correct Answer

C:

EVPN route types carry different information: Type 1 Ethernet auto-discovery, Type 2 MAC/IP, Type 3 inclusive multicast. The appropriate response is to inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally.

Incorrect Answers

A:

“VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic” belongs to a separate EVPN issue: a campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. It does not explain the condition tested here.

B:

“EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops” belongs to a separate EVPN issue: an EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. It does not explain the condition tested here.

D:

“EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence” belongs to a separate EVPN issue: a multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. It does not explain the condition tested here.

Question 991

A Junos enterprise team investigates this incident: A dual-attached Ethernet segment experiences persistent duplicates during link recovery because multihoming election or ESI state differs. Which technical explanation most directly identifies the cause or design principle?

  1. VXLAN encapsulates overlay traffic across an IP underlay; VTEP reachability is necessary even with valid BGP EVPN control-plane state.
  2. VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic.
  3. EVPN route types carry different information: Type 1 Ethernet auto-discovery, Type 2 MAC/IP, Type 3 inclusive multicast.
  4. EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.

Explanation

Correct Answer

D:

EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops. The appropriate response is to inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.

Incorrect Answers

A:

“VXLAN encapsulates overlay traffic across an IP underlay; VTEP reachability is necessary even with valid BGP EVPN control-plane state” belongs to a separate EVPN issue: a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback. It does not explain the condition tested here.

B:

“VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic” belongs to a separate EVPN issue: a campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. It does not explain the condition tested here.

C:

“EVPN route types carry different information: Type 1 Ethernet auto-discovery, Type 2 MAC/IP, Type 3 inclusive multicast” belongs to a separate EVPN issue: a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. It does not explain the condition tested here.

Question 992

A network change is required for the following specific situation: Packets with two different drop precedence values are treated as equally discardable during congestion. Which corrective action is most appropriate?

  1. Assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.
  2. Map the two packet categories to the intended PLP levels and verify drop-profile response.
  3. Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment.
  4. Define a controlled rewrite map for each class and verify high-priority markings remain restricted.

Explanation

Correct Answer

B:

Packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior. Verify this by checking that during controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic.

Incorrect Answers

A:

“Assign the intended service class and scheduler priorities with measured bandwidth needs, then validate” belongs to a separate Class of Service (CoS) issue: two queues use the same scheduler priority, but the business expects one to always win during contention. It does not explain the condition tested here.

C:

“Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment” belongs to a separate Class of Service (CoS) issue: video gets dropped under congestion despite spare capacity because its queue has a too-small delay buffer. It does not explain the condition tested here.

D:

“Define a controlled rewrite map for each class and verify high-priority markings remain restricted” belongs to a separate Class of Service (CoS) issue: a customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic. It does not explain the condition tested here.

Question 993

Select THREE complementary corrective, verification, or preventive controls for this scenario: An uplink becomes a region boundary unexpectedly after an administrator changes an MSTP configuration name on only one switch.

  1. Compare complete region configuration on the peers and restore the approved shared MSTP region values.
  2. Both switches show compatible region membership and intended instance root/port roles.
  3. Adjust Ethernet cable speed and expect different MSTP region digests to converge automatically.
  4. Delete all VLANs from every trunk to clear one stale MVRP registration.
  5. Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN.
  6. Version-control MSTP name, revision and VLAN mapping as one change unit.

Explanation

Correct Answers

A:

Correction: MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map.

B:

Confirmation: Compare complete region configuration on the peers and restore the approved shared MSTP region values.

F:

Prevention of recurrence: MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map.

Incorrect Answers

C:

“Adjust Ethernet cable speed and expect different MSTP region digests to converge automatically” does not address MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map.

D:

“Delete all VLANs from every trunk to clear one stale MVRP registration” is an unsafe response to a different problem: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It is not a valid fix here.

E:

“Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN” is an unsafe response to a different problem: a shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It is not a valid fix here.

Question 994

Select THREE complementary corrective, verification, or preventive controls for this scenario: A campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them.

  1. Maintain representative match and nonmatch tests for filter-based VLAN policies.
  2. Create an independent VSTP instance for every VLAN without checking platform scaling limits.
  3. Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.
  4. Matching test traffic enters the quarantine VLAN while ordinary traffic stays in the expected VLAN.
  5. Assume naming a quarantine VLAN automatically steers matching traffic without an applied filter.
  6. Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled.

Explanation

Correct Answers

A:

Prevention of recurrence: Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point.

C:

Correction: Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point.

D:

Confirmation: Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.

Incorrect Answers

B:

“Create an independent VSTP instance for every VLAN without checking platform scaling limits” is an unsafe response to a different problem: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It is not a valid fix here.

E:

“Assume naming a quarantine VLAN automatically steers matching traffic without an applied filter” does not address filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point.

F:

“Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled” is an unsafe response to a different problem: a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. It is not a valid fix here.

Question 995

Which suggested shortcut would be especially unsafe for this exact situation? A newly deployed IP phone joins the data network because the switch does not advertise the intended voice VLAN through LLDP-MED.

  1. Include end-to-end marking tests when deploying voice VLANs and new phone models.
  2. Assume generic LLDP chassis identification alone announces the correct voice VLAN and QoS settings.
  3. Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
  4. Test both tagged phone frames and untagged PC frames during phone-port commissioning.

Explanation

Correct Answer

B:

The tempting alternative fails because LLDP-MED extends device discovery with telephony-related network-policy TLVs that need compatible endpoint behavior. The supported action is to enable supported LLDP-MED network policy on the phone-facing port and verify advertisements and phone settings.

Incorrect Answers

A:

That prevention measure relates to a handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN.; it is not the unsafe shortcut described here.

Question 996

A Junos enterprise team investigates this incident: A low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk. Which technical explanation most directly identifies the cause or design principle?

  1. Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface.
  2. CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings.
  3. Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.
  4. Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract.

Explanation

Correct Answer

A:

Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface. The appropriate response is to associate the approved scheduler map with the correct egress interface and confirm class queue counters.

Incorrect Answers

B:

“CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings” belongs to a separate Class of Service (CoS) issue: a customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic. It does not explain the condition tested here.

C:

“Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic” belongs to a separate Class of Service (CoS) issue: an uplink meets long-term bandwidth policy but legitimate short bursts exceed the token-bucket allowance. It does not explain the condition tested here.

D:

“Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract” belongs to a separate Class of Service (CoS) issue: a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. It does not explain the condition tested here.

Question 997

A Junos enterprise team investigates this incident: A MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. Which technical explanation most directly identifies the cause or design principle?

  1. 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized.
  2. Captive portal requires a supported browser interception and authentication-to-authorization sequence.
  3. Server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access.
  4. MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication.

Explanation

Correct Answer

D:

MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication. The appropriate response is to confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.

Incorrect Answers

A:

“802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized” belongs to a separate Layer 2 Authentication and Access Control issue: an access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It does not explain the condition tested here.

B:

“Captive portal requires a supported browser interception and authentication-to-authorization sequence” belongs to a separate Layer 2 Authentication and Access Control issue: guest users on an EX switch see no captive login page because browser HTTP redirects are not being applied on the intended VLAN. It does not explain the condition tested here.

C:

“Server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access” belongs to a separate Layer 2 Authentication and Access Control issue: an enterprise fallback design accidentally places unauthenticated users into the production network when all RADIUS servers fail. It does not explain the condition tested here.

Question 998

A Junos enterprise team investigates this incident: A network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN. Which technical explanation most directly identifies the cause or design principle?

  1. Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.
  2. Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink.
  3. Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
  4. Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context.

Explanation

Correct Answer

C:

Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns. The appropriate response is to compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.

Incorrect Answers

A:

“Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough” belongs to a separate Ethernet Switching and Spanning Tree issue: an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently. It does not explain the condition tested here.

B:

“Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink” belongs to a separate Ethernet Switching and Spanning Tree issue: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It does not explain the condition tested here.

D:

“Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.

Question 999

A Junos enterprise team investigates this incident: A MAC RADIUS policy authenticates a known camera but applies the broad employee VLAN instead of a camera-only network. Which technical explanation most directly identifies the cause or design principle?

  1. Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary.
  2. 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed.
  3. Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices.
  4. MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision.

Explanation

Correct Answer

D:

MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision. The appropriate response is to assign the authenticated device to the authorized restricted network profile and verify effective VLAN/filter.

Incorrect Answers

A:

“Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary” belongs to a separate Layer 2 Authentication and Access Control issue: an EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization. It does not explain the condition tested here.

B:

“802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed” belongs to a separate Layer 2 Authentication and Access Control issue: an engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them. It does not explain the condition tested here.

C:

“Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices” belongs to a separate Layer 2 Authentication and Access Control issue: a captive portal requirement is applied to a headless barcode scanner that has no web browser to follow its redirect. It does not explain the condition tested here.

Question 1000

A network change is required for the following specific situation: A branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. Which corrective action is most appropriate?

  1. Associate the approved scheduler map with the correct egress interface and confirm class queue counters.
  2. Configure supported egress shaping at the bottleneck and verify throughput and queue behavior.
  3. Apply the appropriate interface rewrite rule and verify the contract-specific egress code points.
  4. Map the two packet categories to the intended PLP levels and verify drop-profile response.

Explanation

Correct Answer

B:

Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract. Verify this by checking that outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.

Incorrect Answers

A:

“Associate the approved scheduler map with the correct egress interface and confirm class queue counters” belongs to a separate Class of Service (CoS) issue: a campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing. It does not explain the condition tested here.

C:

“Apply the appropriate interface rewrite rule and verify the contract-specific egress code points” belongs to a separate Class of Service (CoS) issue: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It does not explain the condition tested here.

D:

“Map the two packet categories to the intended PLP levels and verify drop-profile response” belongs to a separate Class of Service (CoS) issue: a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.