Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 18

Question 170

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: An access VLAN floods every multicast packet because IGMP snooping state was lost during migration.

  1. Disable IGMP snooping everywhere and assume uncontrolled flooding is equivalent to correct membership delivery.
  2. Assume inet.0 always controls PIM RPF even when an alternate multicast RPF table is configured.
  3. Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
  4. Assume an ASM (*,G) join identifies and restricts a unique approved source by itself.
  5. Subscribed receivers get the stream without unnecessary flood to ports that did not join.

Explanation

Correct Answers

C:

Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports. This addresses the dependency that IGMP reports express receiver interest, and IGMP snooping uses that interest to constrain Layer 2 replication.

E:

Subscribed receivers get the stream without unnecessary flood to ports that did not join. The specific steps required are to inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.

Incorrect Answers

A:

“Disable IGMP snooping everywhere and assume uncontrolled flooding is equivalent to correct membership delivery” does not address IGMP reports express receiver interest, and IGMP snooping uses that interest to constrain Layer 2 replication.

B:

“Assume inet.0 always controls PIM RPF even when an alternate multicast RPF table is configured” is an unsafe response to a different problem: a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. It is not a valid fix here.

D:

“Assume an ASM (*,G) join identifies and restricts a unique approved source by itself” is an unsafe response to a different problem: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It is not a valid fix here.

Question 171

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A host moves between leafs and the destination leaf still forwards toward the previous MAC location.

  1. Assume an Ethernet payload that fits a non-VXLAN path always fits once the VXLAN overhead is added.
  2. The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding.
  3. Reuse one VNI for unrelated tenants and assume local VLAN names alone prevent overlay mixing.
  4. Assume a data-plane VXLAN tunnel automatically updates every remote leaf's EVPN MAC reachability without Type 2 control-plane exchange.
  5. Check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.

Explanation

Correct Answers

B:

The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding. The specific steps required are to check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.

E:

Check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain. This addresses the dependency that EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane.

Incorrect Answers

A:

“Assume an Ethernet payload that fits a non-VXLAN path always fits once the VXLAN overhead is added” is an unsafe response to a different problem: an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. It is not a valid fix here.

C:

“Reuse one VNI for unrelated tenants and assume local VLAN names alone prevent overlay mixing” is an unsafe response to a different problem: a fabric uses conflicting VLAN-to-VNI mappings on two leaf switches, bridging different tenant segments together. It is not a valid fix here.

D:

“Assume a data-plane VXLAN tunnel automatically updates every remote leaf's EVPN MAC reachability without Type 2 control-plane exchange” does not address EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane.

Question 172

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A router prefers a longer AS path when a higher LOCAL_PREF makes that route win, surprising the transit team.

  1. Disable all iBGP loop protection and expect the route-reflector hierarchy to be unnecessary.
  2. Disable BGP AS-loop safeguards globally to accept any route repeating the local AS.
  3. Examine both attributes in the received route detail and update the explicit routing policy rather than guessing.
  4. Assume the shortest AS path must win regardless of any LOCAL_PREF difference.
  5. After policy correction, chosen path and attribute ordering match documented routing intent.

Explanation

Correct Answers

C:

Examine both attributes in the received route detail and update the explicit routing policy rather than guessing. This addresses the dependency that for eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner.

E:

After policy correction, chosen path and attribute ordering match documented routing intent. The specific steps required are to examine both attributes in the received route detail and update the explicit routing policy rather than guessing.

Incorrect Answers

A:

“Disable all iBGP loop protection and expect the route-reflector hierarchy to be unnecessary” is an unsafe response to a different problem: a route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster. It is not a valid fix here.

B:

“Disable BGP AS-loop safeguards globally to accept any route repeating the local AS” is an unsafe response to a different problem: the local AS appears in a received external BGP AS_PATH and the route is rejected despite valid prefix reachability. It is not a valid fix here.

D:

“Assume the shortest AS path must win regardless of any LOCAL_PREF difference” does not address for eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner.

Question 173

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants.

  1. Grant unbounded port access to all endpoints instead of diagnosing the RADIUS/EAP path.
  2. Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event.
  3. Check authentication result classification and map the rejected user to an appropriate deny or reject response.
  4. A nonresponding guest gets its intended limited VLAN while invalid credentials never receive guest privilege.
  5. Mark every unknown MAC as trusted and give it unrestricted data-VLAN access.

Explanation

Correct Answers

C:

Check authentication result classification and map the rejected user to an appropriate deny or reject response. This addresses the dependency that guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.

D:

A nonresponding guest gets its intended limited VLAN while invalid credentials never receive guest privilege. The specific steps required are to check authentication result classification and map the rejected user to an appropriate deny or reject response.

Incorrect Answers

A:

“Grant unbounded port access to all endpoints instead of diagnosing the RADIUS/EAP path” is an unsafe response to a different problem: a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. It is not a valid fix here.

B:

“Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event” does not address guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.

E:

“Mark every unknown MAC as trusted and give it unrestricted data-VLAN access” is an unsafe response to a different problem: an industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service. It is not a valid fix here.

Question 174

A Junos enterprise team investigates this incident: A private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. Which technical explanation most directly identifies the cause or design principle?

  1. Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles.
  2. Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.
  3. A private VLAN community allows permitted communication within its community; isolated behavior is stricter.
  4. Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink.

Explanation

Correct Answer

B:

Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough. The appropriate response is to configure supported L2PT for the required control protocols and verify provider-edge handling.

Incorrect Answers

A:

“Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. It does not explain the condition tested here.

C:

“A private VLAN community allows permitted communication within its community; isolated behavior is stricter” belongs to a separate Ethernet Switching and Spanning Tree issue: members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication. It does not explain the condition tested here.

D:

“Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink” belongs to a separate Ethernet Switching and Spanning Tree issue: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It does not explain the condition tested here.

Question 175

A network change is required for the following specific situation: An IPv6 branch outage is misdiagnosed using only IPv4 pings, despite OSPFv3 neighbors using IPv6 link-local messaging. Which corrective action is most appropriate?

  1. Review external metric type and value at the originator, then apply the documented traffic-engineering policy.
  2. Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.
  3. Compare configured interface areas with the approved topology and put both interfaces in the intended matching area.
  4. Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.

Explanation

Correct Answer

D:

IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges. Verify this by checking that the affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests.

Incorrect Answers

A:

“Review external metric type and value at the originator, then apply the documented traffic-engineering policy” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.

B:

“Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR starts leaking a management static route into the enterprise IGP after a permissive export term was introduced. It does not explain the condition tested here.

C:

“Compare configured interface areas with the approved topology and put both interfaces in the intended matching area” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus OSPF interface is accidentally placed in area 0 while its neighbor advertises a nonbackbone area, preventing a Full adjacency. It does not explain the condition tested here.

Question 176

A network change is required for the following specific situation: An access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. Which corrective action is most appropriate?

  1. Compare OSPF interface timers and align the two peers to approved Hello and dead values.
  2. Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.
  3. Move OSPFv3 participation to the correct active interface and verify neighbor and IPv6 RIB state.
  4. Review external metric type and value at the originator, then apply the documented traffic-engineering policy.

Explanation

Correct Answer

A:

OSPF neighbors require compatible Hello and dead interval settings on the shared interface. Verify this by checking that stable Hellos and Full neighbor state persist through repeated protocol interval checks.

Incorrect Answers

B:

“Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core node shows a missing route while remote LSDBs include the corresponding external LSA after a local policy change. It does not explain the condition tested here.

C:

“Move OSPFv3 participation to the correct active interface and verify neighbor and IPv6 RIB state” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. It does not explain the condition tested here.

D:

“Review external metric type and value at the originator, then apply the documented traffic-engineering policy” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.

Question 177

The team believes it has resolved this Junos issue: A multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. Which observation best verifies the specific intended result?

  1. The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended.
  2. The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types.
  3. Both peers report a consistent Ethernet segment and failover preserves authorized connectivity.
  4. BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered.

Explanation

Correct Answer

C:

Both peers report a consistent Ethernet segment and failover preserves authorized connectivity. This checks the relevant result after align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes.

Incorrect Answers

A:

“The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended” belongs to a separate EVPN issue: a new leaf imports VNI reachability but packets disappear because its VXLAN tunnel endpoint IP is unresolved. It does not explain the condition tested here.

B:

“The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types” belongs to a separate EVPN issue: a fabric advertises Type 3 routes and claims this proves specific remote host MACs are reachable. It does not explain the condition tested here.

D:

“BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered” belongs to a separate EVPN issue: a bridge domain has valid unicast Type 2 entries yet remote VTEPs do not discover a new participating segment for BUM forwarding. It does not explain the condition tested here.

Question 178

Which suggested shortcut would be especially unsafe for this exact situation? A carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path.

  1. Test path equivalence, forwarding and failure convergence before enabling transit ECMP.
  2. Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
  3. Disable BGP AS-loop safeguards globally to accept any route repeating the local AS.
  4. Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP.

Explanation

Correct Answer

C:

The tempting alternative fails because the default BGP AS-path loop check rejects routes containing the local autonomous system to prevent loops. The supported action is to check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks.

Incorrect Answers

A:

That prevention measure relates to two eBGP sessions over different transports are expected to provide ECMP but only one forwarding next hop appears.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to an iBGP egress advertisement forwards a transit next hop that branch routers cannot resolve, creating traffic blackholes.; it is not the unsafe shortcut described here.

Question 179

Which suggested shortcut would be especially unsafe for this exact situation? A transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated.

  1. Include show route hidden and policy term hit checks in BGP troubleshooting playbooks.
  2. Monitor AS-path anomalies and validate inter-AS topology changes before enabling export.
  3. Increase the route's MED while leaving BGP transport reachability and hop settings incorrect.
  4. Maintain expected BGP attribute decisions for every primary/secondary transit policy.

Explanation

Correct Answer

C:

The tempting alternative fails because multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints. The supported action is to verify endpoint reachability and configure appropriate multihop session parameters and security controls.

Incorrect Answers

A:

That prevention measure relates to a Junos route is hidden by import policy, but the team troubleshoots only local physical interfaces.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a router prefers a longer AS path when a higher LOCAL_PREF makes that route win, surprising the transit team.; it is not the unsafe shortcut described here.

Question 180

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: An 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently.

  1. Disable private VLAN restrictions entirely as a shortcut to reach a single shared uplink service.
  2. Configure supported L2PT for the required control protocols and verify provider-edge handling.
  3. Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN.
  4. The customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology.
  5. Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled.

Explanation

Correct Answers

B:

Configure supported L2PT for the required control protocols and verify provider-edge handling. This addresses the dependency that layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.

D:

The customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology. The specific steps required are to configure supported L2PT for the required control protocols and verify provider-edge handling.

Incorrect Answers

A:

“Disable private VLAN restrictions entirely as a shortcut to reach a single shared uplink service” is an unsafe response to a different problem: a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. It is not a valid fix here.

C:

“Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN” is an unsafe response to a different problem: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It is not a valid fix here.

E:

“Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled” does not address layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.