Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 20

Question 190

The team believes it has resolved this Junos issue: A branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice. Which observation best verifies the specific intended result?

  1. Voice traffic receives the required scheduled service at the congested egress without starving other classes.
  2. Only approved media streams leave with high-priority code points; backup traffic uses its designated mark.
  3. Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses.
  4. Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.

Explanation

Correct Answer

B:

Only approved media streams leave with high-priority code points; backup traffic uses its designated mark. This checks the relevant result after define a controlled rewrite map for each class and verify high-priority markings remain restricted.

Incorrect Answers

A:

“Voice traffic receives the required scheduled service at the congested egress without starving other classes” belongs to a separate Class of Service (CoS) issue: a low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk. It does not explain the condition tested here.

C:

“Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses” belongs to a separate Class of Service (CoS) issue: a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. It does not explain the condition tested here.

D:

“Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses” belongs to a separate Class of Service (CoS) issue: a branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. It does not explain the condition tested here.

Question 191

The team believes it has resolved this Junos issue: A voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. Which observation best verifies the specific intended result?

  1. Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface.
  2. Tagged voice packets retain the intended service class through the access and aggregation paths.
  3. The device stays powered during peak consumption and Junos reports no power-denial events.
  4. The phone or location service reports the correct emergency location for the new access port.

Explanation

Correct Answer

B:

Tagged voice packets retain the intended service class through the access and aggregation paths. This checks the relevant result after verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.

Incorrect Answers

A:

“Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface” belongs to a separate IP Telephony Features issue: a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature. It does not explain the condition tested here.

C:

“The device stays powered during peak consumption and Junos reports no power-denial events” belongs to a separate IP Telephony Features issue: an emergency intercom can establish Ethernet link but loses power during activity because its PD class is not supported by that port. It does not explain the condition tested here.

D:

“The phone or location service reports the correct emergency location for the new access port” belongs to a separate IP Telephony Features issue: an IP phone uses the wrong location information for emergency response after a switch move. It does not explain the condition tested here.

Question 192

Select THREE complementary corrective, verification, or preventive controls for this scenario: A PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface.

  1. Treat SSM group membership as source-agnostic and subscribe to the group without source information.
  2. The required PIM neighbors appear and downstream join state tracks active interested receivers.
  3. Enable PIM on the approved routed VLAN interface and inspect neighbor and join state.
  4. Use a unique group name as the only security boundary and rely on routers to infer its scope.
  5. Create an IGMP group entry alone and expect it to establish PIM adjacency between routers.
  6. Include routed-interface PIM enrollment in the multicast deployment checklist.

Explanation

Correct Answers

B:

Confirmation: Enable PIM on the approved routed VLAN interface and inspect neighbor and join state.

C:

Correction: PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.

F:

Prevention of recurrence: PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.

Incorrect Answers

A:

“Treat SSM group membership as source-agnostic and subscribe to the group without source information” is an unsafe response to a different problem: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It is not a valid fix here.

D:

“Use a unique group name as the only security boundary and rely on routers to infer its scope” is an unsafe response to a different problem: a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. It is not a valid fix here.

E:

“Create an IGMP group entry alone and expect it to establish PIM adjacency between routers” does not address PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.

Question 193

To prevent recurrence of this precise networking failure, which practice should be adopted? A host moves between leafs and the destination leaf still forwards toward the previous MAC location.

  1. Track route import, MAC mobility and aging during host migration tests.
  2. Maintain a central VNI registry and test cross-tenant isolation on each leaf rollout.
  3. Audit ESI consistency and platform-supported multihoming mode across paired leafs.
  4. Test multihoming election and per-VLAN failover after attaching new dual-homed devices.

Explanation

Correct Answer

A:

Track route import, MAC mobility and aging during host migration tests. This guards against EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane.

Incorrect Answers

B:

“Maintain a central VNI registry and test cross-tenant isolation on each leaf rollout” belongs to a separate EVPN issue: a campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. It does not explain the condition tested here.

C:

“Audit ESI consistency and platform-supported multihoming mode across paired leafs” belongs to a separate EVPN issue: a multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. It does not explain the condition tested here.

D:

“Test multihoming election and per-VLAN failover after attaching new dual-homed devices” belongs to a separate EVPN issue: an EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. It does not explain the condition tested here.

Question 194

A Junos enterprise team investigates this incident: A multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain. Which technical explanation most directly identifies the cause or design principle?

  1. Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it.
  2. MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions.
  3. BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
  4. Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints.

Explanation

Correct Answer

D:

Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints. The appropriate response is to verify endpoint reachability and configure appropriate multihop session parameters and security controls.

Incorrect Answers

A:

“Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it” belongs to a separate Border Gateway Protocol (BGP) issue: a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. It does not explain the condition tested here.

B:

“MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.

C:

“BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately” belongs to a separate Border Gateway Protocol (BGP) issue: a prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor. It does not explain the condition tested here.

Question 195

The team believes it has resolved this Junos issue: A powered endpoint detects a Junos switch but fails to negotiate voice prioritization because only ordinary LLDP is enabled. Which observation best verifies the specific intended result?

  1. The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN.
  2. The phone receives stable negotiated power and the chassis stays within its supported budget under peak load.
  3. Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface.
  4. The device stays powered during peak consumption and Junos reports no power-denial events.

Explanation

Correct Answer

C:

Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface. This checks the relevant result after review LLDP and LLDP-MED operational status and enable supported MED policy for phone access.

Incorrect Answers

A:

“The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.

B:

“The phone receives stable negotiated power and the chassis stays within its supported budget under peak load” belongs to a separate IP Telephony Features issue: a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget. It does not explain the condition tested here.

D:

“The device stays powered during peak consumption and Junos reports no power-denial events” belongs to a separate IP Telephony Features issue: an emergency intercom can establish Ethernet link but loses power during activity because its PD class is not supported by that port. It does not explain the condition tested here.

Question 196

To prevent recurrence of this precise networking failure, which practice should be adopted? An edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams.

  1. Include routed-interface PIM enrollment in the multicast deployment checklist.
  2. Run both allow and deny group tests against multicast policy whenever prefixes are revised.
  3. Include source address changes in SSM subscription-management procedures.
  4. Monitor IGMP membership churn and snooping state when moving clients between VLANs.

Explanation

Correct Answer

B:

Run both allow and deny group tests against multicast policy whenever prefixes are revised. This guards against policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked.

Incorrect Answers

A:

“Include routed-interface PIM enrollment in the multicast deployment checklist” belongs to a separate IP Multicast issue: a PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface. It does not explain the condition tested here.

C:

“Include source address changes in SSM subscription-management procedures” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.

D:

“Monitor IGMP membership churn and snooping state when moving clients between VLANs” belongs to a separate IP Multicast issue: a receiver port stops getting multicast because IGMP membership was not processed by the access switch after an interface move. It does not explain the condition tested here.

Question 197

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A dual-attached Ethernet segment experiences persistent duplicates during link recovery because multihoming election or ESI state differs.

  1. Enable independent active forwarding on every multihomed link while ignoring ESI and DF controls.
  2. BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates.
  3. Assume an Ethernet payload that fits a non-VXLAN path always fits once the VXLAN overhead is added.
  4. Treat a single learned MAC/IP Type 2 route as guaranteed proof of correct BUM participation for every VTEP.
  5. Inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.

Explanation

Correct Answers

B:

BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates. The specific steps required are to inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.

E:

Inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration. This addresses the dependency that EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.

Incorrect Answers

A:

“Enable independent active forwarding on every multihomed link while ignoring ESI and DF controls” does not address EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.

C:

“Assume an Ethernet payload that fits a non-VXLAN path always fits once the VXLAN overhead is added” is an unsafe response to a different problem: an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. It is not a valid fix here.

D:

“Treat a single learned MAC/IP Type 2 route as guaranteed proof of correct BUM participation for every VTEP” is an unsafe response to a different problem: a VNI is active on two leafs but unknown-unicast or broadcast replication never reaches the remote side. It is not a valid fix here.

Question 198

A Junos enterprise team investigates this incident: A traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. Which technical explanation most directly identifies the cause or design principle?

  1. Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.
  2. Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification.
  3. Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface.
  4. Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays.

Explanation

Correct Answer

A:

Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic. The appropriate response is to measure burst patterns and adjust the policer burst configuration within the authorized service contract.

Incorrect Answers

B:

“Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification” belongs to a separate Class of Service (CoS) issue: an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It does not explain the condition tested here.

C:

“Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface” belongs to a separate Class of Service (CoS) issue: a campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing. It does not explain the condition tested here.

D:

“Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays” belongs to a separate Class of Service (CoS) issue: a forwarding-class configuration sends critical routing packets to a queue used for bulk backups and adjacency stability degrades under load. It does not explain the condition tested here.

Question 199

The team believes it has resolved this Junos issue: An EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. Which observation best verifies the specific intended result?

  1. The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types.
  2. The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding.
  3. BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates.
  4. The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended.

Explanation

Correct Answer

C:

BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates. This checks the relevant result after inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.

Incorrect Answers

A:

“The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types” belongs to a separate EVPN issue: a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. It does not explain the condition tested here.

B:

“The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding” belongs to a separate EVPN issue: a new endpoint MAC is learned at a remote VTEP but never reaches the receiving leaf's EVPN control-plane table. It does not explain the condition tested here.

D:

“The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended” belongs to a separate EVPN issue: a new leaf imports VNI reachability but packets disappear because its VXLAN tunnel endpoint IP is unresolved. It does not explain the condition tested here.

Question 200

A Junos enterprise team investigates this incident: A Junos route is hidden by import policy, but the team troubleshoots only local physical interfaces. Which technical explanation most directly identifies the cause or design principle?

  1. A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session.
  2. MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions.
  3. Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints.
  4. LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors.

Explanation

Correct Answer

A:

A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session. The appropriate response is to inspect hidden-route reason, incoming attributes and import-policy decisions, then correct the authorized match.

Incorrect Answers

B:

“MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.

C:

“Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints” belongs to a separate Border Gateway Protocol (BGP) issue: a multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain. It does not explain the condition tested here.

D:

“LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors” belongs to a separate Border Gateway Protocol (BGP) issue: an operator tries to make a remote AS prefer one inbound path using LOCAL_PREF that the remote eBGP peer never receives. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.