100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 650
Which suggested shortcut would be especially unsafe for this exact situation? A low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk.
- Differentiate ingress policing from egress shaping when designing bandwidth controls.
- Create a scheduler definition in configuration but never bind the scheduler map to egress interfaces.
- Test marking, PLP assignment and drop policy together rather than checking only DSCP fields.
- Keep a documented forwarding-class inventory and test default mappings after service changes.
Explanation
Correct Answer
B:The tempting alternative fails because egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface. The supported action is to associate the approved scheduler map with the correct egress interface and confirm class queue counters.
Incorrect Answers
A:That prevention measure relates to a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a forwarding-class configuration sends critical routing packets to a queue used for bulk backups and adjacency stability degrades under load.; it is not the unsafe shortcut described here.
Question 651
To prevent recurrence of this precise networking failure, which practice should be adopted? A multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain.
- Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews.
- Record eBGP peer transport depth and endpoint routing in deployment templates.
- Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
- Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP.
Explanation
Correct Answer
B:Record eBGP peer transport depth and endpoint routing in deployment templates. This guards against multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints.
Incorrect Answers
A:“Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews” belongs to a separate Border Gateway Protocol (BGP) issue: an operator tries to make a remote AS prefer one inbound path using LOCAL_PREF that the remote eBGP peer never receives. It does not explain the condition tested here.
C:“Include next-hop reachability tests in iBGP and route-reflector deployment acceptance” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. It does not explain the condition tested here.
D:“Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP” belongs to a separate Border Gateway Protocol (BGP) issue: a route-reflector client receives an external destination but lacks the underlay path to the advertised next hop. It does not explain the condition tested here.
Question 652
To prevent recurrence of this precise networking failure, which practice should be adopted? An eBGP import policy unexpectedly accepts more-specific prefixes outside the approved customer allocation.
- Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
- Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP.
- Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes.
- Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews.
Explanation
Correct Answer
A:Audit prefix and mask-length boundaries with positive and negative routing-policy tests. This guards against BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
Incorrect Answers
B:“Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP” belongs to a separate Border Gateway Protocol (BGP) issue: a route-reflector client receives an external destination but lacks the underlay path to the advertised next hop. It does not explain the condition tested here.
C:“Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes” belongs to a separate Border Gateway Protocol (BGP) issue: a provider-facing policy stops honoring a route-tag community after a new import policy changes the attached communities. It does not explain the condition tested here.
D:“Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews” belongs to a separate Border Gateway Protocol (BGP) issue: a dual-homed site changes internal LOCAL_PREF but sees no change in the other autonomous system's inbound traffic choice. It does not explain the condition tested here.
Question 653
To prevent recurrence of this precise networking failure, which practice should be adopted? A boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling.
- Test ingress classification separately from egress rewrite at every trust boundary.
- Validate classifier, scheduler map and interface association as a complete CoS chain.
- Keep a documented forwarding-class inventory and test default mappings after service changes.
- Plan buffer and shaping rates against provider handoff capacity and expected burst size.
Explanation
Correct Answer
A:Test ingress classification separately from egress rewrite at every trust boundary. This guards against Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings.
Incorrect Answers
B:“Validate classifier, scheduler map and interface association as a complete CoS chain” belongs to a separate Class of Service (CoS) issue: a campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing. It does not explain the condition tested here.
C:“Keep a documented forwarding-class inventory and test default mappings after service changes” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.
D:“Plan buffer and shaping rates against provider handoff capacity and expected burst size” belongs to a separate Class of Service (CoS) issue: a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. It does not explain the condition tested here.
Question 654
Which suggested shortcut would be especially unsafe for this exact situation? A campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping.
- Audit ESI consistency and platform-supported multihoming mode across paired leafs.
- Test multihoming election and per-VLAN failover after attaching new dual-homed devices.
- Reuse one VNI for unrelated tenants and assume local VLAN names alone prevent overlay mixing.
- Track route import, MAC mobility and aging during host migration tests.
Explanation
Correct Answer
C:The tempting alternative fails because VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic. The supported action is to compare VLAN-to-VNI and bridge-domain assignments on all leafs and correct them against the approved tenant map.
Incorrect Answers
A:That prevention measure relates to a shared Ethernet segment loses its fast convergence properties after an ESI-LAG peer receives an inconsistent configuration.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a dual-attached Ethernet segment experiences persistent duplicates during link recovery because multihoming election or ESI state differs.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a new endpoint MAC is learned at a remote VTEP but never reaches the receiving leaf's EVPN control-plane table.; it is not the unsafe shortcut described here.
Question 655
Which suggested shortcut would be especially unsafe for this exact situation? A branch uplink uses area 0.0.0.6 on one router and area 0.0.0.9 on its peer after a template copy.
- Document expected external metrics and run primary/backup failover tests during policy changes.
- Keep IPv4 and IPv6 routing verification separate for dual-stack maintenance.
- Change only router IDs while leaving the mismatched interface areas intact.
- Verify both protocol RIB candidates and active next-hop selection in dual-stack change tests.
Explanation
Correct Answer
C:The tempting alternative fails because OSPF neighbors must agree on the area context to form adjacency on the common link. The supported action is to compare configured interface areas with the approved topology and put both interfaces in the intended matching area.
Incorrect Answers
A:That prevention measure relates to an OSPF policy update redistributes a route without an appropriate external metric, shifting traffic to a slow backup.; it is not the unsafe shortcut described here.
B:That prevention measure relates to an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a team wrongly concludes OSPFv3 failed when inet6.0 shows a static route active and the OSPFv3 candidate inactive.; it is not the unsafe shortcut described here.
Question 656
A Junos enterprise team investigates this incident: A financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. Which technical explanation most directly identifies the cause or design principle?
- Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow.
- Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.
- Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture.
- Multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy.
Explanation
Correct Answer
D:Multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy. The appropriate response is to configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
Incorrect Answers
A:“Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.
B:“Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic” belongs to a separate IP Multicast issue: a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. It does not explain the condition tested here.
C:“Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture” belongs to a separate IP Multicast issue: an Anycast RP design uses two RP addresses that do not share the intended anycast identity, producing inconsistent joins. It does not explain the condition tested here.
Question 657
The team believes it has resolved this Junos issue: A branch uplink uses area 0.0.0.6 on one router and area 0.0.0.9 on its peer after a template copy. Which observation best verifies the specific intended result?
- An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0.
- The preferred primary route wins when healthy and the backup becomes active on a controlled failure.
- OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements.
- The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency.
Explanation
Correct Answer
C:OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements. This checks the relevant result after compare configured interface areas with the approved topology and put both interfaces in the intended matching area.
Incorrect Answers
A:“An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. It does not explain the condition tested here.
B:“The preferred primary route wins when healthy and the backup becomes active on a controlled failure” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.
D:“The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6 route learned through OSPFv3 is absent from the forwarding table because a more preferred static route covers the same prefix. It does not explain the condition tested here.
Question 658
A network change is required for the following specific situation: A legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. Which corrective action is most appropriate?
- Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
- Assign the authenticated device to the authorized restricted network profile and verify effective VLAN/filter.
- Inspect packet exchange and classify the endpoint before selecting a supported fallback method.
- Select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies.
Explanation
Correct Answer
B:MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision. Verify this by checking that the known device reaches only permitted destinations and cannot reach employee or management resources.
Incorrect Answers
A:“Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration” belongs to a separate Layer 2 Authentication and Access Control issue: a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. It does not explain the condition tested here.
C:“Inspect packet exchange and classify the endpoint before selecting a supported fallback method” belongs to a separate Layer 2 Authentication and Access Control issue: a RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. It does not explain the condition tested here.
D:“Select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies” instead concerns another network scenario: An access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It does not address the requirement here.
Question 659
The team believes it has resolved this Junos issue: A low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk. Which observation best verifies the specific intended result?
- Observed queue counters show voice packets in the designated forwarding class after classification.
- Voice traffic receives the required scheduled service at the congested egress without starving other classes.
- Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.
- During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic.
Explanation
Correct Answer
B:Voice traffic receives the required scheduled service at the congested egress without starving other classes. This checks the relevant result after associate the approved scheduler map with the correct egress interface and confirm class queue counters.
Incorrect Answers
A:“Observed queue counters show voice packets in the designated forwarding class after classification” belongs to a separate Class of Service (CoS) issue: a campus uplink transmits marked video as ordinary data because no behavior-aggregate classifier is attached at ingress. It does not explain the condition tested here.
C:“Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses” belongs to a separate Class of Service (CoS) issue: a branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. It does not explain the condition tested here.
D:“During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic” belongs to a separate Class of Service (CoS) issue: a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class. It does not explain the condition tested here.
Question 660
Which suggested shortcut would be especially unsafe for this exact situation? A network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN.
- Create an independent VSTP instance for every VLAN without checking platform scaling limits.
- Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned.
- Maintain representative match and nonmatch tests for filter-based VLAN policies.
- Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries.
Explanation
Correct Answer
A:The tempting alternative fails because MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control. The supported action is to create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior.
Incorrect Answers
B:That prevention measure relates to a dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a policy-based VLAN filter moves matching device traffic to a quarantine VLAN but a rule fails to match the intended MAC or packet fields.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff.; it is not the unsafe shortcut described here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests