Palo Alto Networks NGFW-Engineer Exam Dumps, Practice Test Questions

100% Latest & Updated Palo Alto Networks NGFW-Engineer Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Palo Alto Networks NGFW-Engineer  Premium File
$54.99
$49.99

NGFW-Engineer Premium File

  • Premium File: 143 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

NGFW-Engineer Premium File

Palo Alto Networks NGFW-Engineer  Premium File
  • Premium File: 143 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Palo Alto Networks NGFW-Engineer Practice Test 15

Question 140

New VPN traffic uses a tunnel interface yet matches no policy even though the remote subnet is reachable. Which TWO measures together provide a direct verification and a safe deployment control? Choose TWO.

  1. Confirm the link pair forwards permitted transit frames and that interzone logs identify the virtual-wire zones
  2. Use a fresh session log to identify the matched interzone policy decision
  3. Define separate security zones and narrowly scoped interzone access for the subnets
  4. Limit vendor tunnel zone access to named applications and destinations
  5. Test a representative frame in each allowed VLAN before promoting the change

Explanation

Correct Answers

B:

Use a fresh session log to identify the matched interzone policy decision. The session log isolates zone-policy denial from IPsec negotiation.

D:

Limit vendor tunnel zone access to named applications and destinations. Route reachability to internal prefixes is broader than the authorized service need.

Incorrect Answers

A:

Confirm the link pair forwards permitted transit frames and that interzone logs identify the virtual-wire zones. The test demonstrates transparent forwarding through the inspection path. This case instead requires “Use a fresh session log to identify the matched interzone policy decision | Limit vendor tunnel zone access to named applications and destinations”.

C:

Define separate security zones and narrowly scoped interzone access for the subnets. Routing reachability alone should not permit every application between segments. That feature does not establish the specific result needed in this situation.

E:

Test a representative frame in each allowed VLAN before promoting the change. This catches segmentation errors that a single untagged ping would miss. Its effect is distinct from the intended configuration outcome here.

Question 141

Two active firewalls must inspect sessions concurrently in a topology designed for active/active service. What is the most appropriate next engineering action for this situation?

  1. Configure the supported active/active HA pair with the appropriate session synchronization and forwarding design
  2. Include the production-critical interface or link group in HA link monitoring
  3. Configure HA link monitoring with the correct aggregate or member failure conditions
  4. Set suitable metrics and monitor the primary path so the backup becomes eligible after failure

Explanation

Correct Answer

A:

Active/active requires a compatible topology and state-sharing behavior across both active peers.

Incorrect Answers

B:

Include the production-critical interface or link group in HA link monitoring. Only configured monitored failures can trigger that HA condition. This case instead requires “Configure the supported active/active HA pair with the appropriate session synchronization and forwarding design”.

C:

Configure HA link monitoring with the correct aggregate or member failure conditions. Link monitoring can trigger HA transitions based on the physical link groups. This case instead requires “Configure the supported active/active HA pair with the appropriate session synchronization and forwarding design”.

D:

Set suitable metrics and monitor the primary path so the backup becomes eligible after failure. Preference and path health together determine which route forwards. This action would leave the decisive condition in the case unchanged. This case instead requires “Configure the supported active/active HA pair with the appropriate session synchronization and forwarding design”.

Question 142

Two active firewalls must inspect sessions concurrently in a topology designed for active/active service. After the change, which observation would most directly prove the intended behavior?

  1. Inspect HA2 link status and synchronized session counters before failover
  2. Compare probe-loss events with actual application reachability before changing thresholds
  3. Verify both peers' active states and cross-peer session handling during asymmetric test flows
  4. Disconnect the monitored links during a scheduled drill and observe HA role change

Explanation

Correct Answer

C:

Verify both peers' active states and cross-peer session handling during asymmetric test flows. Observing both peers process authorized traffic confirms the active/active design.

Incorrect Answers

A:

Inspect HA2 link status and synchronized session counters before failover. This verifies state transfer instead of merely peer heartbeats. This does not show that the specified firewall path works as intended.

B:

Compare probe-loss events with actual application reachability before changing thresholds. Correlation distinguishes false positives from genuine route failures. Its effect is distinct from the intended configuration outcome here.

D:

Disconnect the monitored links during a scheduled drill and observe HA role change. This validates the selected any/all monitoring policy. That feature does not establish the specific result needed in this situation.

Question 143

Two active firewalls must inspect sessions concurrently in a topology designed for active/active service. During validation, the following problem is reported: A passive peer does not normally handle live production sessions. Which defect or mistaken assumption most directly accounts for this result?

  1. Failing to advertise the new active forwarding identity to adjacent neighbors
  2. Configuring a pair as active/passive while expecting simultaneous traffic processing on both appliances
  3. Defining the monitored link group with a failure condition that never reaches the desired threshold
  4. Ignoring out-of-sync configuration because both devices show healthy dataplane ports

Explanation

Correct Answer

B:

Configuring a pair as active/passive while expecting simultaneous traffic processing on both appliances. A passive peer does not normally handle live production sessions.

Incorrect Answers

A:

Failing to advertise the new active forwarding identity to adjacent neighbors. Hosts may keep sending packets toward the old active path. The issue evaluated here is “Configuring a pair as active/passive while expecting simultaneous traffic processing on both appliances”.

C:

Defining the monitored link group with a failure condition that never reaches the desired threshold. The active peer may remain active after required capacity is lost. The mismatch would persist because this choice targets another control point. The issue evaluated here is “Configuring a pair as active/passive while expecting simultaneous traffic processing on both appliances”.

D:

Ignoring out-of-sync configuration because both devices show healthy dataplane ports. Port status cannot establish consistent policy and network settings across peers. The observed failure here would remain unresolved by that step.

Question 144

Two active firewalls must inspect sessions concurrently in a topology designed for active/active service. Before releasing the change, which safeguard most directly reduces the associated operational or security risk?

  1. Validate asymmetric-routing and failover assumptions before connecting both active peers
  2. Stage the export restriction with a peer-level recovery plan
  3. Avoid enabling administrative services on untrusted internet-facing interfaces
  4. Include upstream switch and routing convergence in the scheduled failover drill

Explanation

Correct Answer

A:

Validate asymmetric-routing and failover assumptions before connecting both active peers. Unplanned session paths can break stateful inspection.

Incorrect Answers

B:

Stage the export restriction with a peer-level recovery plan. Aggressive filtering can unexpectedly withdraw valid partner routes. That feature does not establish the specific result needed in this situation.

C:

Avoid enabling administrative services on untrusted internet-facing interfaces. Administrative reachability should not grow as a side effect of routing changes. Its effect is distinct from the intended configuration outcome here. The relevant safeguard here is “Validate asymmetric-routing and failover assumptions before connecting both active peers”.

D:

Include upstream switch and routing convergence in the scheduled failover drill. Firewall HA state alone does not prove connected network readiness. That protection is useful, but it does not control the risk introduced by this change.

Question 145

A datacenter uses active/active firewalls and must avoid sending a new session to a peer without required state. What is the most appropriate next engineering action for this situation?

  1. Validate session synchronization and HA packet-forwarding paths between active peers
  2. Include the production-critical interface or link group in HA link monitoring
  3. Set suitable metrics and monitor the primary path so the backup becomes eligible after failure
  4. Deploy an active/passive HA pair with compatible interfaces, HA links, and failover settings

Explanation

Correct Answer

A:

Concurrent peers must share or forward the relevant session context for consistent inspection.

Incorrect Answers

B:

Include the production-critical interface or link group in HA link monitoring. Only configured monitored failures can trigger that HA condition. The mismatch would persist because this choice targets another control point.

C:

Set suitable metrics and monitor the primary path so the backup becomes eligible after failure. Preference and path health together determine which route forwards. The case depends on a different setting or test to meet its requirement.

D:

Only the active peer processes normal data traffic while the passive peer is prepared to take over. That feature does not establish the specific result needed in this situation.

Question 146

A datacenter uses active/active firewalls and must avoid sending a new session to a peer without required state. After the change, which observation would most directly prove the intended behavior?

  1. Use an actual forwarding lookup and probe monitor state for the failed destination
  2. Observe neighbor-table changes and new service sessions immediately after failover
  3. Inspect per-peer session ownership and cross-peer forwarding counters for a test flow
  4. Compare probe-loss events with actual application reachability before changing thresholds

Explanation

Correct Answer

C:

Inspect per-peer session ownership and cross-peer forwarding counters for a test flow. These show whether traffic is processed by its session owner.

Incorrect Answers

A:

Use an actual forwarding lookup and probe monitor state for the failed destination. These show whether route selection follows valid health information. Its effect is distinct from the intended configuration outcome here. The relevant evidence here is “Inspect per-peer session ownership and cross-peer forwarding counters for a test flow”.

B:

Observe neighbor-table changes and new service sessions immediately after failover. This measures actual network convergence to the new active peer. That observation would not by itself verify this particular change.

D:

Compare probe-loss events with actual application reachability before changing thresholds. Correlation distinguishes false positives from genuine route failures. That feature does not establish the specific result needed in this situation. The relevant evidence here is “Inspect per-peer session ownership and cross-peer forwarding counters for a test flow”.

Question 147

A datacenter uses active/active firewalls and must avoid sending a new session to a peer without required state. During validation, the following problem is reported: Packets can reach a peer unable to process the session consistently. Which defect or mistaken assumption most directly accounts for this result?

  1. Assuming a healthy HA1 control heartbeat automatically carries complete session state
  2. Missing the required cross-peer state or forwarding connectivity for asymmetric traffic
  3. Ignoring out-of-sync configuration because both devices show healthy dataplane ports
  4. Assuming that a route's presence in the candidate configuration proves it is installed and healthy

Explanation

Correct Answer

B:

Missing the required cross-peer state or forwarding connectivity for asymmetric traffic. Packets can reach a peer unable to process the session consistently.

Incorrect Answers

A:

Assuming a healthy HA1 control heartbeat automatically carries complete session state. Control-plane health does not substitute for the HA2 data connection. This action would leave the decisive condition in the case unchanged.

C:

Ignoring out-of-sync configuration because both devices show healthy dataplane ports. Port status cannot establish consistent policy and network settings across peers. The mismatch would persist because this choice targets another control point.

D:

Assuming that a route's presence in the candidate configuration proves it is installed and healthy. Configuration and effective forwarding can differ. The issue evaluated here is “Missing the required cross-peer state or forwarding connectivity for asymmetric traffic”.

Question 148

A datacenter uses active/active firewalls and must avoid sending a new session to a peer without required state. Before releasing the change, which safeguard most directly reduces the associated operational or security risk?

  1. Test application reply paths after each route transition
  2. Approve partner-specific prefixes and deny access across the partner zones by default
  3. Test failure of each HA link before production and confirm supported fallback behavior
  4. Use explicit prefix filters and maximum-prefix safeguards on the peering

Explanation

Correct Answer

C:

Test failure of each HA link before production and confirm supported fallback behavior. HA design must account for state channels as well as external data links.

Incorrect Answers

A:

An apparently healthy outbound failover can still fail because the partner lacks a return route. That protection is useful, but it does not control the risk introduced by this change. The relevant safeguard here is “Test failure of each HA link before production and confirm supported fallback behavior”.

B:

Approve partner-specific prefixes and deny access across the partner zones by default. Separation prevents accidental third-party transit between VPNs. That feature does not establish the specific result needed in this situation.

D:

Use explicit prefix filters and maximum-prefix safeguards on the peering. An external session must not import uncontrolled routes into production. Its effect is distinct from the intended configuration outcome here.

Question 149

After changing an active/active design, the operator sees two peers active but an application stalls on return traffic. What is the most appropriate next engineering action for this situation?

  1. Resolve peer version, HA management and configuration synchronization conditions before failover
  2. Examine session ownership and HA3 forwarding behavior where the platform uses it
  3. Validate supported ARP/gratuitous ARP and MAC transition behavior after takeover
  4. Include the production-critical interface or link group in HA link monitoring

Explanation

Correct Answer

B:

Return packets arriving at another peer can require HA packet forwarding to session owner.

Incorrect Answers

A:

A passive firewall with outdated policy may take over with the wrong enforcement settings. Its effect is distinct from the intended configuration outcome here.

C:

Validate supported ARP/gratuitous ARP and MAC transition behavior after takeover. Adjacent switches and clients must learn which peer now forwards the subnet. This case instead requires “Examine session ownership and HA3 forwarding behavior where the platform uses it”.

D:

Include the production-critical interface or link group in HA link monitoring. Only configured monitored failures can trigger that HA condition. This action would leave the decisive condition in the case unchanged. This case instead requires “Examine session ownership and HA3 forwarding behavior where the platform uses it”.

Question 150

After changing an active/active design, the operator sees two peers active but an application stalls on return traffic. After the change, which observation would most directly prove the intended behavior?

  1. Compare session counters and packet handling on both active peers
  2. Observe neighbor-table changes and new service sessions immediately after failover
  3. Confirm active and passive peer states plus synchronized running configuration
  4. Disconnect the monitored links during a scheduled drill and observe HA role change

Explanation

Correct Answer

A:

Compare session counters and packet handling on both active peers. This detects asymmetric state handling rather than a routing-only issue.

Incorrect Answers

B:

Observe neighbor-table changes and new service sessions immediately after failover. This measures actual network convergence to the new active peer. The relevant evidence here is “Compare session counters and packet handling on both active peers”.

C:

Confirm active and passive peer states plus synchronized running configuration. The standby must have the state and configuration needed for takeover. That observation would not by itself verify this particular change. The relevant evidence here is “Compare session counters and packet handling on both active peers”.

D:

Disconnect the monitored links during a scheduled drill and observe HA role change. This validates the selected any/all monitoring policy. Its effect is distinct from the intended configuration outcome here.

Palo Alto Networks Certified Next-Generation Firewall Engineer (NGFW-Engineer) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.