Palo Alto Networks NGFW-Engineer Exam Dumps, Practice Test Questions

100% Latest & Updated Palo Alto Networks NGFW-Engineer Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Palo Alto Networks NGFW-Engineer  Premium File
$54.99
$49.99

NGFW-Engineer Premium File

  • Premium File: 143 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

NGFW-Engineer Premium File

Palo Alto Networks NGFW-Engineer  Premium File
  • Premium File: 143 Questions & Answers. Last update: Nov 9, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Palo Alto Networks NGFW-Engineer Practice Test 17

Question 160

A paired firewall has an HA1 control link but no reliable session synchronization under a failover test. Which TWO measures together provide a direct verification and a safe deployment control? Choose TWO.

  1. Inspect HA2 link status and synchronized session counters before failover
  2. Permit only approved management DNS resolvers and avoid disabling TLS hostname verification
  3. Fail the monitored path and verify the default route leaves the effective forwarding table
  4. Plan redundant HA control and data paths appropriate to the deployment
  5. Use a stable representative monitor target and a tested secondary route

Explanation

Correct Answers

A:

Inspect HA2 link status and synchronized session counters before failover. This verifies state transfer instead of merely peer heartbeats.

D:

Plan redundant HA control and data paths appropriate to the deployment. A single HA cable failure must not defeat the desired resilience.

Incorrect Answers

B:

Permit only approved management DNS resolvers and avoid disabling TLS hostname verification. DNS troubleshooting should not lead to insecure update trust decisions. Its effect is distinct from the intended configuration outcome here.

C:

Fail the monitored path and verify the default route leaves the effective forwarding table. A probe alarm without route withdrawal is insufficient for failover. This case instead requires “Inspect HA2 link status and synchronized session counters before failover | Plan redundant HA control and data paths appropriate to the deployment”.

E:

Use a stable representative monitor target and a tested secondary route. Bad targets or thresholds can blackhole traffic or oscillate routing. That feature does not establish the specific result needed in this situation.

Question 161

An active/passive pair keeps losing service during failovers because devices on the LAN retain stale L2 neighbor state. What is the most appropriate next engineering action for this situation?

  1. Use HA path monitoring against a suitable reachable target rather than link-only monitoring
  2. Validate supported ARP/gratuitous ARP and MAC transition behavior after takeover
  3. Configure the supported active/active HA pair with the appropriate session synchronization and forwarding design
  4. Configure HA link monitoring with the correct aggregate or member failure conditions

Explanation

Correct Answer

B:

Validate supported ARP/gratuitous ARP and MAC transition behavior after takeover. Adjacent switches and clients must learn which peer now forwards the subnet.

Incorrect Answers

A:

Use HA path monitoring against a suitable reachable target rather than link-only monitoring. Path monitoring detects lost end-to-end reachability beyond the local Ethernet carrier. This action would leave the decisive condition in the case unchanged.

C:

Active/active requires a compatible topology and state-sharing behavior across both active peers. That feature does not establish the specific result needed in this situation.

D:

Configure HA link monitoring with the correct aggregate or member failure conditions. Link monitoring can trigger HA transitions based on the physical link groups. This case instead requires “Validate supported ARP/gratuitous ARP and MAC transition behavior after takeover”.

Question 162

An active/passive pair keeps losing service during failovers because devices on the LAN retain stale L2 neighbor state. After the change, which observation would most directly prove the intended behavior?

  1. Verify both peers' active states and cross-peer session handling during asymmetric test flows
  2. Check path-monitor target status and the configured failover condition
  3. Compare session counters and packet handling on both active peers
  4. Observe neighbor-table changes and new service sessions immediately after failover

Explanation

Correct Answer

D:

Observe neighbor-table changes and new service sessions immediately after failover. This measures actual network convergence to the new active peer.

Incorrect Answers

A:

Verify both peers' active states and cross-peer session handling during asymmetric test flows. Observing both peers process authorized traffic confirms the active/active design. Its effect is distinct from the intended configuration outcome here.

B:

Check path-monitor target status and the configured failover condition. The test proves the firewall distinguishes remote path failure from local link state. That feature does not establish the specific result needed in this situation.

C:

Compare session counters and packet handling on both active peers. This detects asymmetric state handling rather than a routing-only issue. This does not show that the specified firewall path works as intended.

Question 163

An active/passive pair keeps losing service during failovers because devices on the LAN retain stale L2 neighbor state. During validation, the following problem is reported: Hosts may keep sending packets toward the old active path. Which defect or mistaken assumption most directly accounts for this result?

  1. Defining the monitored link group with a failure condition that never reaches the desired threshold
  2. Monitoring a different management interface while ignoring the actual production uplink
  3. Monitoring only the local next-hop ARP reachability despite upstream internet loss
  4. Failing to advertise the new active forwarding identity to adjacent neighbors

Explanation

Correct Answer

D:

Failing to advertise the new active forwarding identity to adjacent neighbors. Hosts may keep sending packets toward the old active path.

Incorrect Answers

A:

Defining the monitored link group with a failure condition that never reaches the desired threshold. The active peer may remain active after required capacity is lost. The mismatch would persist because this choice targets another control point. The issue evaluated here is “Failing to advertise the new active forwarding identity to adjacent neighbors”.

B:

Monitoring a different management interface while ignoring the actual production uplink. The critical data-plane failure never satisfies the failover trigger. The issue evaluated here is “Failing to advertise the new active forwarding identity to adjacent neighbors”.

C:

Monitoring only the local next-hop ARP reachability despite upstream internet loss. The route can remain installed through a useless path. The observed failure here would remain unresolved by that step. The issue evaluated here is “Failing to advertise the new active forwarding identity to adjacent neighbors”.

Question 164

An active/passive pair keeps losing service during failovers because devices on the LAN retain stale L2 neighbor state. Before releasing the change, which safeguard most directly reduces the associated operational or security risk?

  1. Use a stable representative monitor target and a tested secondary route
  2. Confirm corporate egress capacity and fail behavior before enabling full tunnel for every user
  3. Keep an approved bypass and rollback plan for an inline virtual-wire change
  4. Include upstream switch and routing convergence in the scheduled failover drill

Explanation

Correct Answer

D:

Include upstream switch and routing convergence in the scheduled failover drill. Firewall HA state alone does not prove connected network readiness.

Incorrect Answers

A:

Use a stable representative monitor target and a tested secondary route. Bad targets or thresholds can blackhole traffic or oscillate routing. That protection is useful, but it does not control the risk introduced by this change. The relevant safeguard here is “Include upstream switch and routing convergence in the scheduled failover drill”.

B:

Confirm corporate egress capacity and fail behavior before enabling full tunnel for every user. Moving all browsing through headquarters can create outages or bottlenecks. That feature does not establish the specific result needed in this situation. The relevant safeguard here is “Include upstream switch and routing convergence in the scheduled failover drill”.

C:

Keep an approved bypass and rollback plan for an inline virtual-wire change. An inline failure can interrupt an otherwise healthy upstream network. Its effect is distinct from the intended configuration outcome here. The relevant safeguard here is “Include upstream switch and routing convergence in the scheduled failover drill”.

Question 165

An HA upgrade must protect a critical service while each peer receives a supported PAN-OS release. What is the most appropriate next engineering action for this situation?

  1. Use a documented sequential active/passive upgrade process with compatibility and failover checks
  2. Examine session ownership and HA3 forwarding behavior where the platform uses it
  3. Configure a supported static-route path monitor to withdraw the route upon probe failure
  4. Configure HA link monitoring with the correct aggregate or member failure conditions

Explanation

Correct Answer

A:

Use a documented sequential active/passive upgrade process with compatibility and failover checks. Upgrading one peer at a time preserves the available forwarding role when supported.

Incorrect Answers

B:

Return packets arriving at another peer can require HA packet forwarding to session owner. The case depends on a different setting or test to meet its requirement.

C:

Path monitoring can remove a stale static route when the downstream destination is unreachable. The mismatch would persist because this choice targets another control point. This case instead requires “Use a documented sequential active/passive upgrade process with compatibility and failover checks”.

D:

Configure HA link monitoring with the correct aggregate or member failure conditions. Link monitoring can trigger HA transitions based on the physical link groups. Its effect is distinct from the intended configuration outcome here. This case instead requires “Use a documented sequential active/passive upgrade process with compatibility and failover checks”.

Question 166

An HA upgrade must protect a critical service while each peer receives a supported PAN-OS release. After the change, which observation would most directly prove the intended behavior?

  1. Observe the route table before, during, and after a primary-path outage
  2. Check path-monitor target status and the configured failover condition
  3. Compare both peer versions, HA health, and application probes before each role switch
  4. Compare probe-loss events with actual application reachability before changing thresholds

Explanation

Correct Answer

C:

Compare both peer versions, HA health, and application probes before each role switch. The checks confirm that the next upgrade step will not leave an untested active path.

Incorrect Answers

A:

Observe the route table before, during, and after a primary-path outage. The effective next hop should switch and later recover as designed. Its effect is distinct from the intended configuration outcome here. The relevant evidence here is “Compare both peer versions, HA health, and application probes before each role switch”.

B:

Check path-monitor target status and the configured failover condition. The test proves the firewall distinguishes remote path failure from local link state. That observation would not by itself verify this particular change. The relevant evidence here is “Compare both peer versions, HA health, and application probes before each role switch”.

D:

Compare probe-loss events with actual application reachability before changing thresholds. Correlation distinguishes false positives from genuine route failures. That feature does not establish the specific result needed in this situation. The relevant evidence here is “Compare both peer versions, HA health, and application probes before each role switch”.

Question 167

An HA upgrade must protect a critical service while each peer receives a supported PAN-OS release. During validation, the following problem is reported: This removes the planned service redundancy. Which defect or mistaken assumption most directly accounts for this result?

  1. Assuming that a route's presence in the candidate configuration proves it is installed and healthy
  2. Depending only on physical link monitoring when the upstream routing path can fail independently
  3. Restarting both HA peers simultaneously during a live production upgrade
  4. Assuming active/active status alone guarantees both peers know every packet's state

Explanation

Correct Answer

C:

Restarting both HA peers simultaneously during a live production upgrade. This removes the planned service redundancy.

Incorrect Answers

A:

Assuming that a route's presence in the candidate configuration proves it is installed and healthy. Configuration and effective forwarding can differ. This action would leave the decisive condition in the case unchanged. The issue evaluated here is “Restarting both HA peers simultaneously during a live production upgrade”.

B:

Depending only on physical link monitoring when the upstream routing path can fail independently. The cable can remain up while useful connectivity is lost. The mismatch would persist because this choice targets another control point.

D:

Assuming active/active status alone guarantees both peers know every packet's state. Concurrent forwarding requires correct session synchronization and ownership handling. The issue evaluated here is “Restarting both HA peers simultaneously during a live production upgrade”.

Question 168

An HA upgrade must protect a critical service while each peer receives a supported PAN-OS release. Before releasing the change, which safeguard most directly reduces the associated operational or security risk?

  1. Stage the trunk change on one tested VLAN before expanding the allowed tag list
  2. Keep compatible backups and a supported return plan for each upgrade stage
  3. Assess sensitive-app and DNS-leak requirements before allowing internet breakout
  4. Set and test a recovery hold-down policy suitable for the site

Explanation

Correct Answer

B:

Keep compatible backups and a supported return plan for each upgrade stage. A failed software installation should not force irreversible outage decisions.

Incorrect Answers

A:

Stage the trunk change on one tested VLAN before expanding the allowed tag list. A narrow cutover limits disruption and unexpected cross-VLAN connectivity. That feature does not establish the specific result needed in this situation. The relevant safeguard here is “Keep compatible backups and a supported return plan for each upgrade stage”.

C:

Assess sensitive-app and DNS-leak requirements before allowing internet breakout. Local browsing paths alter which traffic receives enterprise inspection. Its effect is distinct from the intended configuration outcome here. The relevant safeguard here is “Keep compatible backups and a supported return plan for each upgrade stage”.

D:

Set and test a recovery hold-down policy suitable for the site. Rapidly changing link states should not cause repeated HA role oscillation. That protection is useful, but it does not control the risk introduced by this change. The relevant safeguard here is “Keep compatible backups and a supported return plan for each upgrade stage”.

Question 169

A firewall uplink port stays electrically up although the upstream router no longer routes traffic to the WAN. What is the most appropriate next engineering action for this situation?

  1. Check installed route preference and the corresponding route-health monitor
  2. Deploy an active/passive HA pair with compatible interfaces, HA links, and failover settings
  3. Use HA path monitoring against a suitable reachable target rather than link-only monitoring
  4. Set suitable metrics and monitor the primary path so the backup becomes eligible after failure

Explanation

Correct Answer

C:

Use HA path monitoring against a suitable reachable target rather than link-only monitoring. Path monitoring detects lost end-to-end reachability beyond the local Ethernet carrier.

Incorrect Answers

A:

Check installed route preference and the corresponding route-health monitor. Forwarding honors selected active routes, not administrators' intended path diagrams. This case instead requires “Use HA path monitoring against a suitable reachable target rather than link-only monitoring”.

B:

Only the active peer processes normal data traffic while the passive peer is prepared to take over. This case instead requires “Use HA path monitoring against a suitable reachable target rather than link-only monitoring”.

D:

Set suitable metrics and monitor the primary path so the backup becomes eligible after failure. Preference and path health together determine which route forwards. This action would leave the decisive condition in the case unchanged. This case instead requires “Use HA path monitoring against a suitable reachable target rather than link-only monitoring”.

Question 170

A firewall uplink port stays electrically up although the upstream router no longer routes traffic to the WAN. After the change, which observation would most directly prove the intended behavior?

  1. Check path-monitor target status and the configured failover condition
  2. Inspect HA2 link status and synchronized session counters before failover
  3. Check VLAN tags on the AE subinterfaces and confirm all intended members are forwarding
  4. Check running configuration synchronization and compare HA state on both firewalls

Explanation

Correct Answer

A:

Check path-monitor target status and the configured failover condition. The test proves the firewall distinguishes remote path failure from local link state.

Incorrect Answers

B:

Inspect HA2 link status and synchronized session counters before failover. This verifies state transfer instead of merely peer heartbeats. Its effect is distinct from the intended configuration outcome here.

C:

This proves the tenant trunks use the logical aggregate rather than mismatched individual ports. The relevant evidence here is “Check path-monitor target status and the configured failover condition”.

D:

Check running configuration synchronization and compare HA state on both firewalls. The comparison verifies standby readiness before a role change. That observation would not by itself verify this particular change.

Palo Alto Networks Certified Next-Generation Firewall Engineer (NGFW-Engineer) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.