100% Latest & Updated Juniper JN0-364 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 480
The route exists in configuration but forwarding fails because the intended outgoing interface is not associated with the link-local next hop. Independently, the review flags the potentially unsafe practice “Declare success solely because the interface has an inet6 address”. Which validation addresses the risk without assuming a particular cause?
- Treat fe80::1 as globally unambiguous across all interfaces
- Inspect IPv6 neighbor table for the selected interface
- Check forwarding-table next hop and IPv6 packet counters
- Inspect the active IPv6 route for a representative /48 address
Explanation
Correct Answer
C:Address presence does not guarantee remote reachability. A configured static route alone does not prove end-to-end IPv6 traffic.
Incorrect Answers
A:A link-local identifier can exist on multiple links.
B:IPv6 forwarding needs link-layer reachability to local next hops.
D:Incorrect prefix length can redirect unintended IPv6 destinations.
Question 481
Two provider routers exchange IPv6 over a core link but OSPFv3 neighbors never reach Full after an area change. The objective is to check OSPFv3 area and interface. Which Junos configuration or design action best satisfies the objective?
- Set both OSPFv3 routers to the same identifier for easier monitoring
- Assume global unicast connectivity is the only possible OSPFv3 control path
- Treat OSPFv2 Type 1 IP subnet information as identical to OSPFv3 LSA layout
- Enable OSPFv3 on the intended IPv6 link with compatible area design
Explanation
Correct Answer
D:OSPFv3 uses IPv6 link operation and OSPF area membership.
Incorrect Answers
A:Duplicate router IDs create identity ambiguity.
B:OSPFv3 local neighbor exchange uses link scope.
C:OSPFv3 uses different prefix-carrying LSAs.
Question 482
Two provider routers exchange IPv6 over a core link but OSPFv3 neighbors never reach Full after an area change. The objective is to verify router IDs. Which operational choice should be prioritized in this design?
- Use distinct 32-bit OSPFv3 router IDs for the participating routers
- Treat OSPFv2 Type 1 IP subnet information as identical to OSPFv3 LSA layout
- Assume global unicast connectivity is the only possible OSPFv3 control path
- Assume an OSPFv2 neighbor alone automatically creates OSPFv3 route exchange
Explanation
Correct Answer
A:OSPFv3 still identifies routers using 32-bit router IDs.
Incorrect Answers
B:OSPFv3 uses different prefix-carrying LSAs.
C:OSPFv3 local neighbor exchange uses link scope.
D:OSPFv2 and OSPFv3 are separate protocol operations.
Question 483
Two provider routers exchange IPv6 over a core link but OSPFv3 neighbors never reach Full after an area change. The objective is to check link-local communication. Which routing or switching control best fits the requirement?
- Assume an OSPFv2 neighbor alone automatically creates OSPFv3 route exchange
- Treat OSPFv2 Type 1 IP subnet information as identical to OSPFv3 LSA layout
- Set both OSPFv3 routers to the same identifier for easier monitoring
- Confirm IPv6 link-local addresses and control traffic exchange on the interface
Explanation
Correct Answer
D:OSPFv3 commonly uses link-local addresses for neighbor exchanges.
Incorrect Answers
A:OSPFv2 and OSPFv3 are separate protocol operations.
B:OSPFv3 uses different prefix-carrying LSAs.
C:Duplicate router IDs create identity ambiguity.
Question 484
Two provider routers exchange IPv6 over a core link but OSPFv3 neighbors never reach Full after an area change. The objective is to verify prefix LSAs. Which verification should be performed before approving the change?
- Check OSPFv3 link and intra-area prefix LSAs and installed IPv6 routes
- Assume an OSPFv2 neighbor alone automatically creates OSPFv3 route exchange
- Assume global unicast connectivity is the only possible OSPFv3 control path
- Set both OSPFv3 routers to the same identifier for easier monitoring
Explanation
Correct Answer
A:OSPFv3 separates prefix reachability from some topology LSA contents.
Incorrect Answers
B:OSPFv2 and OSPFv3 are separate protocol operations.
C:OSPFv3 local neighbor exchange uses link scope.
D:Duplicate router IDs create identity ambiguity.
Question 485
Two provider routers exchange IPv6 over a core link but OSPFv3 neighbors never reach Full after an area change. Two objectives apply: (1) check OSPFv3 area and interface; and (2) check link-local communication. Which TWO controls together satisfy the requirements? Choose TWO.
- Enable OSPFv3 on the intended IPv6 link with compatible area design
- Set both OSPFv3 routers to the same identifier for easier monitoring
- Assume global unicast connectivity is the only possible OSPFv3 control path
- Confirm IPv6 link-local addresses and control traffic exchange on the interface
- Assume an OSPFv2 neighbor alone automatically creates OSPFv3 route exchange
Explanation
Correct Answers
A:OSPFv3 uses IPv6 link operation and OSPF area membership.
D:OSPFv3 commonly uses link-local addresses for neighbor exchanges.
Incorrect Answers
B:Duplicate router IDs create identity ambiguity.
C:OSPFv3 local neighbor exchange uses link scope.
E:OSPFv2 and OSPFv3 are separate protocol operations.
Question 486
Two provider routers exchange IPv6 over a core link but OSPFv3 neighbors never reach Full after an area change. Three objectives apply: (1) check OSPFv3 area and interface; (2) check link-local communication; and (3) verify prefix LSAs. Which THREE controls together satisfy the requirements? Choose THREE.
- Enable OSPFv3 on the intended IPv6 link with compatible area design
- Treat OSPFv2 Type 1 IP subnet information as identical to OSPFv3 LSA layout
- Check OSPFv3 link and intra-area prefix LSAs and installed IPv6 routes
- Assume an OSPFv2 neighbor alone automatically creates OSPFv3 route exchange
- Set both OSPFv3 routers to the same identifier for easier monitoring
- Confirm IPv6 link-local addresses and control traffic exchange on the interface
Explanation
Correct Answers
A:OSPFv3 uses IPv6 link operation and OSPF area membership.
C:OSPFv3 separates prefix reachability from some topology LSA contents.
F:OSPFv3 commonly uses link-local addresses for neighbor exchanges.
Incorrect Answers
B:OSPFv3 uses different prefix-carrying LSAs.
D:OSPFv2 and OSPFv3 are separate protocol operations.
E:Duplicate router IDs create identity ambiguity.
Question 487
OSPFv3 interface logs show Hello packets while remote IPv6 service prefixes remain missing from the routing table. Independently, the review flags the potentially unsafe practice “Assume an OSPFv2 neighbor alone automatically creates OSPFv3 route exchange”. Which inspection best evaluates that practice?
- Inspect OSPFv3 interface and area membership
- Assume global unicast connectivity is the only possible OSPFv3 control path
- Compare OSPFv3 router IDs and neighbor state
- Inspect OSPFv3 database prefix entries and inet6 route table
Explanation
Correct Answer
A:OSPFv2 and OSPFv3 are separate protocol operations. OSPFv3 uses IPv6 link operation and OSPF area membership.
Incorrect Answers
B:OSPFv3 local neighbor exchange uses link scope.
C:OSPFv3 still identifies routers using 32-bit router IDs.
D:OSPFv3 separates prefix reachability from some topology LSA contents.
Question 488
OSPFv3 interface logs show Hello packets while remote IPv6 service prefixes remain missing from the routing table. Independently, the review flags the potentially unsafe practice “Set both OSPFv3 routers to the same identifier for easier monitoring”. Which evidence most directly tests the flagged assumption?
- Inspect OSPFv3 database prefix entries and inet6 route table
- Assume an OSPFv2 neighbor alone automatically creates OSPFv3 route exchange
- Inspect peer link-local addresses and Hello counters
- Compare OSPFv3 router IDs and neighbor state
Explanation
Correct Answer
D:Duplicate router IDs create identity ambiguity. OSPFv3 still identifies routers using 32-bit router IDs.
Incorrect Answers
A:OSPFv3 separates prefix reachability from some topology LSA contents.
B:OSPFv2 and OSPFv3 are separate protocol operations.
C:OSPFv3 commonly uses link-local addresses for neighbor exchanges.
Question 489
OSPFv3 interface logs show Hello packets while remote IPv6 service prefixes remain missing from the routing table. Independently, the review flags the potentially unsafe practice “Assume global unicast connectivity is the only possible OSPFv3 control path”. Which diagnostic check tests this potentially unsafe choice?
- Inspect OSPFv3 database prefix entries and inet6 route table
- Inspect peer link-local addresses and Hello counters
- Inspect OSPFv3 interface and area membership
- Set both OSPFv3 routers to the same identifier for easier monitoring
Explanation
Correct Answer
B:OSPFv3 local neighbor exchange uses link scope. OSPFv3 commonly uses link-local addresses for neighbor exchanges.
Incorrect Answers
A:OSPFv3 separates prefix reachability from some topology LSA contents.
C:OSPFv3 uses IPv6 link operation and OSPF area membership.
D:Duplicate router IDs create identity ambiguity.
Question 490
OSPFv3 interface logs show Hello packets while remote IPv6 service prefixes remain missing from the routing table. Independently, the review flags the potentially unsafe practice “Treat OSPFv2 Type 1 IP subnet information as identical to OSPFv3 LSA layout”. Which validation addresses the risk without assuming a particular cause?
- Set both OSPFv3 routers to the same identifier for easier monitoring
- Inspect OSPFv3 interface and area membership
- Inspect OSPFv3 database prefix entries and inet6 route table
- Inspect peer link-local addresses and Hello counters
Explanation
Correct Answer
C:OSPFv3 uses different prefix-carrying LSAs. OSPFv3 separates prefix reachability from some topology LSA contents.
Incorrect Answers
A:Duplicate router IDs create identity ambiguity.
B:OSPFv3 uses IPv6 link operation and OSPF area membership.
D:OSPFv3 commonly uses link-local addresses for neighbor exchanges.
Service Provider Routing and Switching, Specialist (JNCIS-SP) (JN0-364) Practice Tests