100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 1
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A private VLAN isolated endpoint reaches the local gateway but cannot access a peer service that should be shared via a permitted promiscuous port.
- Isolated clients reach the shared service but cannot communicate laterally with other isolated clients.
- Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.
- Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled.
- Disable private VLAN restrictions entirely as a shortcut to reach a single shared uplink service.
- Delete all VLANs from every trunk to clear one stale MVRP registration.
Explanation
Correct Answers
A:Isolated clients reach the shared service but cannot communicate laterally with other isolated clients. The specific steps required are to inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.
B:Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity. This addresses the dependency that private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles.
Incorrect Answers
C:“Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled” is an unsafe response to a different problem: a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. It is not a valid fix here.
D:“Disable private VLAN restrictions entirely as a shortcut to reach a single shared uplink service” does not address private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles.
E:“Delete all VLANs from every trunk to clear one stale MVRP registration” is an unsafe response to a different problem: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It is not a valid fix here.
Question 2
A Junos enterprise team investigates this incident: A controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. Which technical explanation most directly identifies the cause or design principle?
- PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.
- MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
- PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
- Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow.
Explanation
Correct Answer
D:Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow. The appropriate response is to select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.
Incorrect Answers
A:“PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree” belongs to a separate IP Multicast issue: a new L3 VLAN permits unicast connectivity but the PIM Hello adjacency remains absent on the active path. It does not explain the condition tested here.
B:“MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points” belongs to a separate IP Multicast issue: a multicast source is active in a different PIM domain but the local ASM RP never learns the source mapping. It does not explain the condition tested here.
C:“PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service” belongs to a separate IP Multicast issue: an ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP. It does not explain the condition tested here.
Question 3
The team believes it has resolved this Junos issue: A guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. Which observation best verifies the specific intended result?
- Measured guest ingress usage remains within policy and permitted business traffic is unaffected.
- Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses.
- Control-plane-related traffic receives the expected queue treatment under simulated load.
- Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic.
Explanation
Correct Answer
A:Measured guest ingress usage remains within policy and permitted business traffic is unaffected. This checks the relevant result after apply a correctly scoped ingress policer with tested rate and burst values on the relevant flow.
Incorrect Answers
B:“Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses” belongs to a separate Class of Service (CoS) issue: two queues use the same scheduler priority, but the business expects one to always win during contention. It does not explain the condition tested here.
C:“Control-plane-related traffic receives the expected queue treatment under simulated load” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.
D:“Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic” belongs to a separate Class of Service (CoS) issue: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It does not explain the condition tested here.
Question 4
The team believes it has resolved this Junos issue: A multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. Which observation best verifies the specific intended result?
- The selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow.
- Only the specified source delivers data to receivers of the chosen SSM group.
- Subscribed receivers get the stream without unnecessary flood to ports that did not join.
- PIM joins build the intended shared tree and the requested group begins forwarding to subscribers.
Explanation
Correct Answer
A:The selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow. This checks the relevant result after identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
Incorrect Answers
B:“Only the specified source delivers data to receivers of the chosen SSM group” belongs to a separate IP Multicast issue: a campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests. It does not explain the condition tested here.
C:“Subscribed receivers get the stream without unnecessary flood to ports that did not join” belongs to a separate IP Multicast issue: an access VLAN floods every multicast packet because IGMP snooping state was lost during migration. It does not explain the condition tested here.
D:“PIM joins build the intended shared tree and the requested group begins forwarding to subscribers” belongs to a separate IP Multicast issue: an ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP. It does not explain the condition tested here.
Question 5
A network change is required for the following specific situation: A branch uplink uses area 0.0.0.6 on one router and area 0.0.0.9 on its peer after a template copy. Which corrective action is most appropriate?
- Compare configured interface areas with the approved topology and put both interfaces in the intended matching area.
- Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.
- Inspect IPv6 interface addresses and OSPFv3 interface participation, then add the intended loopback advertisement within policy.
- Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
Explanation
Correct Answer
A:OSPF neighbors must agree on the area context to form adjacency on the common link. Verify this by checking that OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements.
Incorrect Answers
B:“Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability. It does not explain the condition tested here.
C:“Inspect IPv6 interface addresses and OSPFv3 interface participation, then add the intended loopback advertisement within policy” belongs to a separate Interior Gateway Protocols (IGPs) issue: a replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring. It does not explain the condition tested here.
D:“Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.
Question 6
To prevent recurrence of this precise networking failure, which practice should be adopted? A bridge domain has valid unicast Type 2 entries yet remote VTEPs do not discover a new participating segment for BUM forwarding.
- Test multihoming election and per-VLAN failover after attaching new dual-homed devices.
- Maintain a central VNI registry and test cross-tenant isolation on each leaf rollout.
- Audit ESI consistency and platform-supported multihoming mode across paired leafs.
- Validate EVPN Type 2 and Type 3 propagation separately in new VNI bring-up tests.
Explanation
Correct Answer
D:Validate EVPN Type 2 and Type 3 propagation separately in new VNI bring-up tests. This guards against EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set.
Incorrect Answers
A:“Test multihoming election and per-VLAN failover after attaching new dual-homed devices” belongs to a separate EVPN issue: a dual-attached Ethernet segment experiences persistent duplicates during link recovery because multihoming election or ESI state differs. It does not explain the condition tested here.
B:“Maintain a central VNI registry and test cross-tenant isolation on each leaf rollout” belongs to a separate EVPN issue: a fabric uses conflicting VLAN-to-VNI mappings on two leaf switches, bridging different tenant segments together. It does not explain the condition tested here.
C:“Audit ESI consistency and platform-supported multihoming mode across paired leafs” belongs to a separate EVPN issue: a shared Ethernet segment loses its fast convergence properties after an ESI-LAG peer receives an inconsistent configuration. It does not explain the condition tested here.
Question 7
Which suggested shortcut would be especially unsafe for this exact situation? A VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback.
- Audit ESI consistency and platform-supported multihoming mode across paired leafs.
- Increase a tenant VLAN identifier and expect it to fix an unreachable underlay VTEP IP.
- Keep route-type purpose and acceptance checks in EVPN troubleshooting runbooks.
- Test multihoming election and per-VLAN failover after attaching new dual-homed devices.
Explanation
Correct Answer
B:The tempting alternative fails because VXLAN encapsulates overlay traffic across an IP underlay; VTEP reachability is necessary even with valid BGP EVPN control-plane state. The supported action is to repair authorized underlay routing to remote VTEPs and check tunnel reachability before changing EVPN policies.
Incorrect Answers
A:That prevention measure relates to a shared Ethernet segment loses its fast convergence properties after an ESI-LAG peer receives an inconsistent configuration.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior.; it is not the unsafe shortcut described here.
Question 8
A Junos enterprise team investigates this incident: A route policy lacks an explicit intended default action, and unmatched BGP prefixes behave differently than planned. Which technical explanation most directly identifies the cause or design principle?
- Routing-policy term order and terminal actions determine whether later conditions are evaluated.
- BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers.
- BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions.
- Routing-policy evaluation depends on term matches, flow-control actions and the policy chain, including what happens on no match.
Explanation
Correct Answer
D:Routing-policy evaluation depends on term matches, flow-control actions and the policy chain, including what happens on no match. The appropriate response is to document and test terminal accept or reject behavior along with next-term and next-policy handling.
Incorrect Answers
A:“Routing-policy term order and terminal actions determine whether later conditions are evaluated” belongs to a separate Border Gateway Protocol (BGP) issue: a route with a permissive policy term is accepted before a later deny term can block it. It does not explain the condition tested here.
B:“BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers” belongs to a separate Border Gateway Protocol (BGP) issue: two iBGP exits offer equal reachable routes but the one with higher LOCAL_PREF is not the egress an operator expected. It does not explain the condition tested here.
C:“BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions” belongs to a separate Border Gateway Protocol (BGP) issue: two eBGP sessions over different transports are expected to provide ECMP but only one forwarding next hop appears. It does not explain the condition tested here.
Question 9
The team believes it has resolved this Junos issue: An IPv6 branch outage is misdiagnosed using only IPv4 pings, despite OSPFv3 neighbors using IPv6 link-local messaging. Which observation best verifies the specific intended result?
- The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests.
- OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements.
- Hellos are observed in the routing adjacency and a Full neighbor appears on the intended port.
- The preferred primary route wins when healthy and the backup becomes active on a controlled failure.
Explanation
Correct Answer
A:The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests. This checks the relevant result after check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
Incorrect Answers
B:“OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus OSPF interface is accidentally placed in area 0 while its neighbor advertises a nonbackbone area, preventing a Full adjacency. It does not explain the condition tested here.
C:“Hellos are observed in the routing adjacency and a Full neighbor appears on the intended port” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF neighbor remains Down because the routed transit interface was left passive after a site template rollout. It does not explain the condition tested here.
D:“The preferred primary route wins when healthy and the backup becomes active on a controlled failure” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF policy update redistributes a route without an appropriate external metric, shifting traffic to a slow backup. It does not explain the condition tested here.
Question 10
A Junos enterprise team investigates this incident: A branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. Which technical explanation most directly identifies the cause or design principle?
- Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract.
- Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress.
- CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings.
- Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment.
Explanation
Correct Answer
A:Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract. The appropriate response is to configure supported egress shaping at the bottleneck and verify throughput and queue behavior.
Incorrect Answers
B:“Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress” belongs to a separate Class of Service (CoS) issue: video gets dropped under congestion despite spare capacity because its queue has a too-small delay buffer. It does not explain the condition tested here.
C:“CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings” belongs to a separate Class of Service (CoS) issue: a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice. It does not explain the condition tested here.
D:“Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment” belongs to a separate Class of Service (CoS) issue: voice packets arrive with DSCP EF but are placed into the best-effort queue after a new access interface template is applied. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests