100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 20
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab.
- Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
- Treat SSM group membership as source-agnostic and subscribe to the group without source information.
- The specified groups remain within the approved scope while unrelated enterprise multicast flows continue.
- Enable the same full-bandwidth unicast copy to every receiver and call it multicast optimization.
- Use a unique group name as the only security boundary and rely on routers to infer its scope.
Explanation
Correct Answers
A:Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding. This addresses the dependency that multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy.
C:The specified groups remain within the approved scope while unrelated enterprise multicast flows continue. The specific steps required are to configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
Incorrect Answers
B:“Treat SSM group membership as source-agnostic and subscribe to the group without source information” is an unsafe response to a different problem: a campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests. It is not a valid fix here.
D:“Enable the same full-bandwidth unicast copy to every receiver and call it multicast optimization” is an unsafe response to a different problem: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It is not a valid fix here.
E:“Use a unique group name as the only security boundary and rely on routers to infer its scope” does not address multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy.
Question 21
Select THREE complementary corrective, verification, or preventive controls for this scenario: A prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor.
- Use precise route-filter match conditions and explicit rejection of unauthorized more-specific routes.
- Accept every prefix inside the aggregate without evaluating the agreed maximum prefix length.
- Assume TCP session Established proves every learned prefix has a usable forwarding next hop.
- Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
- Add a second BGP neighbor and assume the forwarding table automatically load-balances every route.
- Allowed customer prefixes are received while unauthorized longer prefixes are absent from accepted routes.
Explanation
Correct Answers
A:Correction: BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
D:Prevention of recurrence: BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
F:Confirmation: Use precise route-filter match conditions and explicit rejection of unauthorized more-specific routes.
Incorrect Answers
B:“Accept every prefix inside the aggregate without evaluating the agreed maximum prefix length” does not address BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
C:“Assume TCP session Established proves every learned prefix has a usable forwarding next hop” is an unsafe response to a different problem: a route-reflector client receives an external destination but lacks the underlay path to the advertised next hop. It is not a valid fix here.
E:“Add a second BGP neighbor and assume the forwarding table automatically load-balances every route” is an unsafe response to a different problem: equal candidate BGP routes are visible but no multipath forwarding entry is installed because eligibility or policy differs. It is not a valid fix here.
Question 22
Select THREE complementary corrective, verification, or preventive controls for this scenario: A backup traffic queue consumes too much buffer and latency-sensitive applications starve during peak bursts.
- Map every packet to the lowest loss priority regardless of its out-of-profile status.
- Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy.
- Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment.
- Increase every queue buffer without considering latency, memory or scheduling priority.
- Review queue buffer tradeoffs and regression-test peak loads before tuning schedulers.
- Queue depth, latency and drop statistics meet documented objectives during realistic traffic load.
Explanation
Correct Answers
C:Correction: Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress.
E:Prevention of recurrence: Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress.
F:Confirmation: Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment.
Incorrect Answers
A:“Map every packet to the lowest loss priority regardless of its out-of-profile status” is an unsafe response to a different problem: a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class. It is not a valid fix here.
B:“Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy” is an unsafe response to a different problem: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It is not a valid fix here.
D:“Increase every queue buffer without considering latency, memory or scheduling priority” does not address queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress.
Question 23
Which suggested shortcut would be especially unsafe for this exact situation? A boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling.
- Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy.
- Test both average-rate enforcement and microburst tolerance for new policer profiles.
- Document trusted-marking boundaries and test both matched and unmatched multifield traffic.
- Establish congestion thresholds and monitor starvation as part of queue-priority design.
Explanation
Correct Answer
A:The tempting alternative fails because Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings. The supported action is to apply the appropriate interface rewrite rule and verify the contract-specific egress code points.
Incorrect Answers
B:That prevention measure relates to an uplink meets long-term bandwidth policy but legitimate short bursts exceed the token-bucket allowance.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier.; it is not the unsafe shortcut described here.
D:That prevention measure relates to two queues use the same scheduler priority, but the business expects one to always win during contention.; it is not the unsafe shortcut described here.
Question 24
A network change is required for the following specific situation: A service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff. Which corrective action is most appropriate?
- Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement.
- Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
- Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
- Inspect primary and secondary private VLAN roles and port membership; restore approved isolated/community mappings.
Explanation
Correct Answer
C:Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context. Verify this by checking that two customers can use overlapping inner VLAN numbers without traffic mixing on the transport.
Incorrect Answers
A:“Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement” belongs to a separate Ethernet Switching and Spanning Tree issue: a VSTP network intended to send voice and data VLANs over different active paths instead blocks both on the same uplink. It does not explain the condition tested here.
B:“Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It does not explain the condition tested here.
D:“Inspect primary and secondary private VLAN roles and port membership; restore approved isolated/community mappings” belongs to a separate Ethernet Switching and Spanning Tree issue: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It does not explain the condition tested here.
Question 25
Which suggested shortcut would be especially unsafe for this exact situation? A network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN.
- Assume the physically fastest switch is always elected as spanning-tree root irrespective of priority.
- Test private-port isolation and uplink reachability after access topology changes.
- Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
- Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned.
Explanation
Correct Answer
A:The tempting alternative fails because spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns. The supported action is to compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.
Incorrect Answers
B:That prevention measure relates to a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream.; it is not the unsafe shortcut described here.
Question 26
Which suggested shortcut would be especially unsafe for this exact situation? A switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet.
- Assume the physically fastest switch is always elected as spanning-tree root irrespective of priority.
- Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
- Check policy coverage and unintended-match cases before activating filter-based steering.
- Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews.
Explanation
Correct Answer
A:The tempting alternative fails because spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns. The supported action is to compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.
Incorrect Answers
B:That prevention measure relates to an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a filter-based VLAN security design uses a rule that catches too many packets and steers legitimate devices into quarantine.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a private VLAN isolated endpoint reaches the local gateway but cannot access a peer service that should be shared via a permitted promiscuous port.; it is not the unsafe shortcut described here.
Question 27
Which suggested shortcut would be especially unsafe for this exact situation? An EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior.
- Enable independent active forwarding on every multihomed link while ignoring ESI and DF controls.
- Include underlay loopback reachability and MTU checks in VXLAN overlay deployment QA.
- Track route import, MAC mobility and aging during host migration tests.
- Validate EVPN Type 2 and Type 3 propagation separately in new VNI bring-up tests.
Explanation
Correct Answer
A:The tempting alternative fails because EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops. The supported action is to inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.
Incorrect Answers
B:That prevention measure relates to a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a host moves between leafs and the destination leaf still forwards toward the previous MAC location.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a bridge domain has valid unicast Type 2 entries yet remote VTEPs do not discover a new participating segment for BUM forwarding.; it is not the unsafe shortcut described here.
Question 28
To prevent recurrence of this precise networking failure, which practice should be adopted? A low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk.
- Validate classifier, scheduler map and interface association as a complete CoS chain.
- Differentiate ingress policing from egress shaping when designing bandwidth controls.
- Keep a documented forwarding-class inventory and test default mappings after service changes.
- Test ingress classification separately from egress rewrite at every trust boundary.
Explanation
Correct Answer
A:Validate classifier, scheduler map and interface association as a complete CoS chain. This guards against egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface.
Incorrect Answers
B:“Differentiate ingress policing from egress shaping when designing bandwidth controls” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.
C:“Keep a documented forwarding-class inventory and test default mappings after service changes” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.
D:“Test ingress classification separately from egress rewrite at every trust boundary” belongs to a separate Class of Service (CoS) issue: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It does not explain the condition tested here.
Question 29
To prevent recurrence of this precise networking failure, which practice should be adopted? A shared multiaccess segment elects an undesired OSPF DR after new routers are connected, and control-plane load rises.
- Specify preferred OSPF DR candidates on shared transit segments and account for non-preemptive elections.
- Record both LSDB presence and local RIB installation in OSPF troubleshooting runbooks.
- Verify both protocol RIB candidates and active next-hop selection in dual-stack change tests.
- Test one allowed and one forbidden route against each export policy term before deployment.
Explanation
Correct Answer
A:Specify preferred OSPF DR candidates on shared transit segments and account for non-preemptive elections. This guards against DR/BDR elections on OSPF broadcast networks affect LSA exchange and can be influenced by priority.
Incorrect Answers
B:“Record both LSDB presence and local RIB installation in OSPF troubleshooting runbooks” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability. It does not explain the condition tested here.
C:“Verify both protocol RIB candidates and active next-hop selection in dual-stack change tests” belongs to a separate Interior Gateway Protocols (IGPs) issue: a team wrongly concludes OSPFv3 failed when inet6.0 shows a static route active and the OSPFv3 candidate inactive. It does not explain the condition tested here.
D:“Test one allowed and one forbidden route against each export policy term before deployment” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch default-route injection stops after a policy matches OSPF-learned routes instead of the intended local static. It does not explain the condition tested here.
Question 30
Which suggested shortcut would be especially unsafe for this exact situation? A laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab.
- Measure receiver interest and multicast forwarding state before scaling new one-to-many services.
- Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.
- Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
- Use a unique group name as the only security boundary and rely on routers to infer its scope.
Explanation
Correct Answer
D:The tempting alternative fails because multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy. The supported action is to configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
Incorrect Answers
A:That prevention measure relates to a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders.; it is not the unsafe shortcut described here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests