Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 104

Question 1030

A network change is required for the following specific situation: A shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. Which corrective action is most appropriate?

  1. Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
  2. Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop.
  3. Map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated.
  4. Create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior.

Explanation

Correct Answer

B:

MVRP distributes VLAN registration information across participating links; a gap can stop propagation. Verify this by checking that the VLAN registration propagates to the intended downstream trunk and reaches its member ports.

Incorrect Answers

A:

“Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It does not explain the condition tested here.

C:

“Map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch rollout splits a team that should communicate within one PVLAN community, while protecting it from another community. It does not explain the condition tested here.

D:

“Create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.

Question 1031

A network change is required for the following specific situation: A traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. Which corrective action is most appropriate?

  1. Measure burst patterns and adjust the policer burst configuration within the authorized service contract.
  2. Define a controlled rewrite map for each class and verify high-priority markings remain restricted.
  3. Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment.
  4. Review the forwarding class and queue map for control and data traffic and apply the intended assignments.

Explanation

Correct Answer

A:

Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic. Verify this by checking that controlled traffic probes pass valid bursts without permitting sustained rate violations.

Incorrect Answers

B:

“Define a controlled rewrite map for each class and verify high-priority markings remain restricted” belongs to a separate Class of Service (CoS) issue: a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice. It does not explain the condition tested here.

C:

“Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment” belongs to a separate Class of Service (CoS) issue: a backup traffic queue consumes too much buffer and latency-sensitive applications starve during peak bursts. It does not explain the condition tested here.

D:

“Review the forwarding class and queue map for control and data traffic and apply the intended assignments” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.

Question 1032

A Junos enterprise team investigates this incident: A BGP export configuration has a broad first match so a specific downstream deny never evaluates the target prefix. Which technical explanation most directly identifies the cause or design principle?

  1. Routing-policy term order and terminal actions determine whether later conditions are evaluated.
  2. BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions.
  3. A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session.
  4. BGP route selection first requires the BGP next hop to resolve through the appropriate routing table.

Explanation

Correct Answer

A:

Routing-policy term order and terminal actions determine whether later conditions are evaluated. The appropriate response is to put specific deny conditions before broad acceptance, and test the policy with representative routes.

Incorrect Answers

B:

“BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions” belongs to a separate Border Gateway Protocol (BGP) issue: equal candidate BGP routes are visible but no multipath forwarding entry is installed because eligibility or policy differs. It does not explain the condition tested here.

C:

“A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session” belongs to a separate Border Gateway Protocol (BGP) issue: a remote prefix appears in incoming BGP updates yet never becomes active after a new route policy was applied. It does not explain the condition tested here.

D:

“BGP route selection first requires the BGP next hop to resolve through the appropriate routing table” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. It does not explain the condition tested here.

Question 1033

A network change is required for the following specific situation: A PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point. Which corrective action is most appropriate?

  1. Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
  2. Design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths.
  3. Check group-to-RP mapping and RP reachability, then repair the RP discovery or explicit mapping.
  4. Update receiver memberships to use the approved source and group, and validate end-to-end (S,G) trees.

Explanation

Correct Answer

C:

PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service. Verify this by checking that PIM joins build the intended shared tree and the requested group begins forwarding to subscribers.

Incorrect Answers

A:

“Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy” belongs to a separate IP Multicast issue: a campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route. It does not explain the condition tested here.

B:

“Design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths” belongs to a separate IP Multicast issue: a one-to-many lecture stream is configured as separate unicast connections and saturates a WAN link to a remote campus. It does not explain the condition tested here.

D:

“Update receiver memberships to use the approved source and group, and validate end-to-end (S,G) trees” belongs to a separate IP Multicast issue: a campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests. It does not explain the condition tested here.

Question 1034

A network change is required for the following specific situation: Members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication. Which corrective action is most appropriate?

  1. Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement.
  2. Inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation.
  3. Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop.
  4. Map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated.

Explanation

Correct Answer

D:

A private VLAN community allows permitted communication within its community; isolated behavior is stricter. Verify this by checking that community members can communicate as intended while cross-community access remains blocked.

Incorrect Answers

A:

“Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.

B:

“Inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation” belongs to a separate Ethernet Switching and Spanning Tree issue: customer traffic emerges with the provider service tag still attached and is rejected by an endpoint expecting ordinary Ethernet. It does not explain the condition tested here.

C:

“Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop” belongs to a separate Ethernet Switching and Spanning Tree issue: a new switch automatically discovers VLAN registrations on one trunk, but an intermediate trunk lacks MVRP participation and blocks the VLAN. It does not explain the condition tested here.

Question 1035

Select THREE complementary corrective, verification, or preventive controls for this scenario: A financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured.

  1. Keep an approved multicast group allocation and test boundary enforcement after routing changes.
  2. Use a unique group name as the only security boundary and rely on routers to infer its scope.
  3. Create an IGMP group entry alone and expect it to establish PIM adjacency between routers.
  4. Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
  5. Require multicast forwarding to follow the receiver's shortest downstream path with no regard to source RPF.
  6. The specified groups remain within the approved scope while unrelated enterprise multicast flows continue.

Explanation

Correct Answers

A:

Prevention of recurrence: Multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy.

D:

Correction: Multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy.

F:

Confirmation: Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.

Incorrect Answers

B:

“Use a unique group name as the only security boundary and rely on routers to infer its scope” does not address multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy.

C:

“Create an IGMP group entry alone and expect it to establish PIM adjacency between routers” is an unsafe response to a different problem: a new L3 VLAN permits unicast connectivity but the PIM Hello adjacency remains absent on the active path. It is not a valid fix here.

E:

“Require multicast forwarding to follow the receiver's shortest downstream path with no regard to source RPF” is an unsafe response to a different problem: a stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work. It is not a valid fix here.

Question 1036

A Junos enterprise team investigates this incident: A credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants. Which technical explanation most directly identifies the cause or design principle?

  1. Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.
  2. MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X.
  3. 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized.
  4. Captive portal requires a supported browser interception and authentication-to-authorization sequence.

Explanation

Correct Answer

A:

Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies. The appropriate response is to check authentication result classification and map the rejected user to an appropriate deny or reject response.

Incorrect Answers

B:

“MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X” belongs to a separate Layer 2 Authentication and Access Control issue: an industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service. It does not explain the condition tested here.

C:

“802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized” belongs to a separate Layer 2 Authentication and Access Control issue: an access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It does not explain the condition tested here.

D:

“Captive portal requires a supported browser interception and authentication-to-authorization sequence” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.

Question 1037

Select THREE complementary corrective, verification, or preventive controls for this scenario: A telephony desk requires multiple authenticated identities while the switch policy allows only one active supplicant.

  1. Select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies.
  2. Use a single unauthenticated open port for the phone and PC to bypass host-mode constraints.
  3. Include downstream device count and authentication method in desk-port templates.
  4. Require the scanner to open a login web page even though the device has no web client.
  5. Both intended endpoints receive their authorized VLAN/policy without permitting unapproved devices.
  6. Assume every 802.1X feature shown in an EX switch guide is identically supported in all Junos OS Evolved interfaces.

Explanation

Correct Answers

A:

Correction: 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized.

C:

Prevention of recurrence: 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized.

E:

Confirmation: Select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies.

Incorrect Answers

B:

“Use a single unauthenticated open port for the phone and PC to bypass host-mode constraints” does not address 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized.

D:

“Require the scanner to open a login web page even though the device has no web client” is an unsafe response to a different problem: a noninteractive sensor is trapped in captive-portal onboarding because operators selected browser authentication for all endpoints. It is not a valid fix here.

F:

“Assume every 802.1X feature shown in an EX switch guide is identically supported in all Junos OS Evolved interfaces” is an unsafe response to a different problem: an engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them. It is not a valid fix here.

Question 1038

A network change is required for the following specific situation: A remote prefix appears in incoming BGP updates yet never becomes active after a new route policy was applied. Which corrective action is most appropriate?

  1. Inspect hidden-route reason, incoming attributes and import-policy decisions, then correct the authorized match.
  2. Check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks.
  3. Inspect per-route local preferences and import policy; set the intended exit's LOCAL_PREF consistently.
  4. Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration.

Explanation

Correct Answer

A:

A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session. Verify this by checking that the desired received prefix is accepted and active while intentionally blocked prefixes stay rejected.

Incorrect Answers

B:

“Check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks” belongs to a separate Border Gateway Protocol (BGP) issue: the local AS appears in a received external BGP AS_PATH and the route is rejected despite valid prefix reachability. It does not explain the condition tested here.

C:

“Inspect per-route local preferences and import policy; set the intended exit's LOCAL_PREF consistently” belongs to a separate Border Gateway Protocol (BGP) issue: two iBGP exits offer equal reachable routes but the one with higher LOCAL_PREF is not the egress an operator expected. It does not explain the condition tested here.

D:

“Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration” belongs to a separate Border Gateway Protocol (BGP) issue: a route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster. It does not explain the condition tested here.

Question 1039

Which suggested shortcut would be especially unsafe for this exact situation? A shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design.

  1. Keep explicit root priority policy and validate elections after device replacement.
  2. Audit edge classifications and apply appropriate BPDU protection on true client-facing ports.
  3. Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN.
  4. Include MVRP adjacency and registration checks in trunk-change reviews.

Explanation

Correct Answer

C:

The tempting alternative fails because private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink. The supported action is to inspect primary and secondary private VLAN roles and port membership; restore approved isolated/community mappings.

Incorrect Answers

A:

That prevention measure relates to a network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade.; it is not the unsafe shortcut described here.

Question 1040

The team believes it has resolved this Junos issue: A BGP export policy advertises a prefix that exists only as an inactive local candidate, despite an expectation of default active-only behavior. Which observation best verifies the specific intended result?

  1. The advertised set matches the documented inactive-BGP exception without changing local forwarding selection.
  2. After policy correction, chosen path and attribute ordering match documented routing intent.
  3. The route is accepted only after the AS-path loop is removed, with stable forwarding.
  4. A loopback-to-loopback BGP session becomes Established and exchanges only permitted NLRI.

Explanation

Correct Answer

A:

The advertised set matches the documented inactive-BGP exception without changing local forwarding selection. This checks the relevant result after inspect active-route selection and the advertise-inactive configuration; keep it only if the external requirement justifies it.

Incorrect Answers

B:

“After policy correction, chosen path and attribute ordering match documented routing intent” belongs to a separate Border Gateway Protocol (BGP) issue: a router prefers a longer AS path when a higher LOCAL_PREF makes that route win, surprising the transit team. It does not explain the condition tested here.

C:

“The route is accepted only after the AS-path loop is removed, with stable forwarding” belongs to a separate Border Gateway Protocol (BGP) issue: a carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path. It does not explain the condition tested here.

D:

“A loopback-to-loopback BGP session becomes Established and exchanges only permitted NLRI” belongs to a separate Border Gateway Protocol (BGP) issue: a multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.