Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 69

Question 680

To prevent recurrence of this precise networking failure, which practice should be adopted? A new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address.

  1. Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
  2. Record eBGP peer transport depth and endpoint routing in deployment templates.
  3. Validate all required BGP address families during dual-stack peer commissioning.
  4. Use multivariable path-selection lab tests before changing MED-based policy.

Explanation

Correct Answer

A:

Include next-hop reachability tests in iBGP and route-reflector deployment acceptance. This guards against BGP route selection first requires the BGP next hop to resolve through the appropriate routing table.

Incorrect Answers

B:

“Record eBGP peer transport depth and endpoint routing in deployment templates” belongs to a separate Border Gateway Protocol (BGP) issue: a transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated. It does not explain the condition tested here.

C:

“Validate all required BGP address families during dual-stack peer commissioning” belongs to a separate Border Gateway Protocol (BGP) issue: BGP peers exchange IPv4 NLRI correctly but a planned IPv6 customer route never appears in inet6.0. It does not explain the condition tested here.

D:

“Use multivariable path-selection lab tests before changing MED-based policy” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.

Question 681

Which suggested shortcut would be especially unsafe for this exact situation? A printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy.

  1. Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises.
  2. Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding.
  3. Verify RADIUS attribute handling and model/release feature support before rolling out dynamic assignment.
  4. Treat a MAC address alone as cryptographic proof of device ownership and elevate access privileges.

Explanation

Correct Answer

D:

The tempting alternative fails because MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication. The supported action is to confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.

Incorrect Answers

A:

That prevention measure relates to after a RADIUS outage, the access switch opens ports broadly instead of applying the approved restricted server-fail VLAN.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a switch receives successful RADIUS Access-Accept but the user still lands in an unexpected VLAN because the dynamic assignment is not supported on that platform.; it is not the unsafe shortcut described here.

Question 682

The team believes it has resolved this Junos issue: A building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. Which observation best verifies the specific intended result?

  1. The customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology.
  2. Isolated clients reach the shared service but cannot communicate laterally with other isolated clients.
  3. Both switches show compatible region membership and intended instance root/port roles.
  4. The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion.

Explanation

Correct Answer

B:

Isolated clients reach the shared service but cannot communicate laterally with other isolated clients. This checks the relevant result after inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.

Incorrect Answers

A:

“The customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology” belongs to a separate Ethernet Switching and Spanning Tree issue: a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. It does not explain the condition tested here.

C:

“Both switches show compatible region membership and intended instance root/port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: an uplink becomes a region boundary unexpectedly after an administrator changes an MSTP configuration name on only one switch. It does not explain the condition tested here.

D:

“The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.

Question 683

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A receiver domain requires discovery of sources known behind another RP, yet inter-RP source information exchange is absent.

  1. Remote ASM receivers can discover the intended source and request multicast delivery through the proper tree.
  2. Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages.
  3. Inspect MSDP peer state and source-active information, then configure the permitted peer relationships.
  4. Assume an ASM (*,G) join identifies and restricts a unique approved source by itself.
  5. Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links.

Explanation

Correct Answers

A:

Remote ASM receivers can discover the intended source and request multicast delivery through the proper tree. The specific steps required are to inspect MSDP peer state and source-active information, then configure the permitted peer relationships.

C:

Inspect MSDP peer state and source-active information, then configure the permitted peer relationships. This addresses the dependency that MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.

Incorrect Answers

B:

“Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages” does not address MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.

D:

“Assume an ASM (*,G) join identifies and restricts a unique approved source by itself” is an unsafe response to a different problem: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It is not a valid fix here.

E:

“Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links” is an unsafe response to a different problem: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It is not a valid fix here.

Question 684

A Junos enterprise team investigates this incident: A new switch automatically discovers VLAN registrations on one trunk, but an intermediate trunk lacks MVRP participation and blocks the VLAN. Which technical explanation most directly identifies the cause or design principle?

  1. Spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections.
  2. MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.
  3. MVRP distributes VLAN registration information across participating links; a gap can stop propagation.
  4. Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point.

Explanation

Correct Answer

C:

MVRP distributes VLAN registration information across participating links; a gap can stop propagation. The appropriate response is to inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop.

Incorrect Answers

A:

“Spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections” belongs to a separate Ethernet Switching and Spanning Tree issue: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It does not explain the condition tested here.

B:

“MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.

D:

“Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them. It does not explain the condition tested here.

Question 685

Which suggested shortcut would be especially unsafe for this exact situation? A multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop.

  1. Run both allow and deny group tests against multicast policy whenever prefixes are revised.
  2. Maintain consistent RP mappings and failover tests across multicast routers.
  3. Assume inet.0 always controls PIM RPF even when an alternate multicast RPF table is configured.
  4. Keep an approved multicast group allocation and test boundary enforcement after routing changes.

Explanation

Correct Answer

C:

The tempting alternative fails because Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic. The supported action is to identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.

Incorrect Answers

A:

That prevention measure relates to an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab.; it is not the unsafe shortcut described here.

Question 686

Which suggested shortcut would be especially unsafe for this exact situation? A captive portal requirement is applied to a headless barcode scanner that has no web browser to follow its redirect.

  1. Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions.
  2. Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding.
  3. Verify RADIUS attribute handling and model/release feature support before rolling out dynamic assignment.
  4. Require the scanner to open a login web page even though the device has no web client.

Explanation

Correct Answer

D:

The tempting alternative fails because captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices. The supported action is to choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.

Incorrect Answers

A:

That prevention measure relates to a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a switch receives successful RADIUS Access-Accept but the user still lands in an unexpected VLAN because the dynamic assignment is not supported on that platform.; it is not the unsafe shortcut described here.

Question 687

To prevent recurrence of this precise networking failure, which practice should be adopted? A campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route.

  1. Review interdomain source-advertisement scope and MSDP peer availability for ASM deployments.
  2. Keep an approved multicast group allocation and test boundary enforcement after routing changes.
  3. Include source address changes in SSM subscription-management procedures.
  4. Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.

Explanation

Correct Answer

D:

Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes. This guards against Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.

Incorrect Answers

A:

“Review interdomain source-advertisement scope and MSDP peer availability for ASM deployments” belongs to a separate IP Multicast issue: a multicast source is active in a different PIM domain but the local ASM RP never learns the source mapping. It does not explain the condition tested here.

B:

“Keep an approved multicast group allocation and test boundary enforcement after routing changes” belongs to a separate IP Multicast issue: a laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab. It does not explain the condition tested here.

C:

“Include source address changes in SSM subscription-management procedures” belongs to a separate IP Multicast issue: a campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests. It does not explain the condition tested here.

Question 688

To prevent recurrence of this precise networking failure, which practice should be adopted? A high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously.

  1. Test both tagged phone frames and untagged PC frames during phone-port commissioning.
  2. Review LLDP-MED state and phone compliance during access-switch template audits.
  3. Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
  4. Synchronize switchport moves with maintained emergency location records.

Explanation

Correct Answer

C:

Capacity-plan PoE power classes and reserved headroom before connecting new powered devices. This guards against PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status.

Incorrect Answers

A:

“Test both tagged phone frames and untagged PC frames during phone-port commissioning” belongs to a separate IP Telephony Features issue: a phone-with-PC desk deployment lets the PC reach data services while the tagged voice stream is dropped by VLAN membership. It does not explain the condition tested here.

B:

“Review LLDP-MED state and phone compliance during access-switch template audits” belongs to a separate IP Telephony Features issue: a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature. It does not explain the condition tested here.

D:

“Synchronize switchport moves with maintained emergency location records” belongs to a separate IP Telephony Features issue: a campus changes a telephone port but LLDP-MED location data remains mapped to an old floor. It does not explain the condition tested here.

Question 689

A Junos enterprise team investigates this incident: A full-mesh iBGP design is converted to route reflection but one peer is treated as an ordinary nonclient and route propagation fails. Which technical explanation most directly identifies the cause or design principle?

  1. LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors.
  2. iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology.
  3. MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions.
  4. BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers.

Explanation

Correct Answer

B:

IBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology. The appropriate response is to inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration.

Incorrect Answers

A:

“LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors” belongs to a separate Border Gateway Protocol (BGP) issue: a dual-homed site changes internal LOCAL_PREF but sees no change in the other autonomous system's inbound traffic choice. It does not explain the condition tested here.

C:

“MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.

D:

“BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers” instead concerns another network scenario: Two iBGP exits offer equal reachable routes but the one with higher LOCAL_PREF is not the egress an operator expected. It does not address the requirement here.

Question 690

To prevent recurrence of this precise networking failure, which practice should be adopted? A carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path.

  1. Record eBGP peer transport depth and endpoint routing in deployment templates.
  2. Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
  3. Use multivariable path-selection lab tests before changing MED-based policy.
  4. Monitor AS-path anomalies and validate inter-AS topology changes before enabling export.

Explanation

Correct Answer

D:

Monitor AS-path anomalies and validate inter-AS topology changes before enabling export. This guards against the default BGP AS-path loop check rejects routes containing the local autonomous system to prevent loops.

Incorrect Answers

A:

“Record eBGP peer transport depth and endpoint routing in deployment templates” belongs to a separate Border Gateway Protocol (BGP) issue: a transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated. It does not explain the condition tested here.

B:

“Include next-hop reachability tests in iBGP and route-reflector deployment acceptance” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. It does not explain the condition tested here.

C:

“Use multivariable path-selection lab tests before changing MED-based policy” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.