Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 76

Question 750

A network change is required for the following specific situation: A private VLAN isolated endpoint reaches the local gateway but cannot access a peer service that should be shared via a permitted promiscuous port. Which corrective action is most appropriate?

  1. Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.
  2. Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
  3. Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.
  4. Inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation.

Explanation

Correct Answer

C:

Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles. Verify this by checking that isolated clients reach the shared service but cannot communicate laterally with other isolated clients.

Incorrect Answers

A:

“Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet. It does not explain the condition tested here.

B:

“Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.

D:

“Inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation” belongs to a separate Ethernet Switching and Spanning Tree issue: customer traffic emerges with the provider service tag still attached and is rejected by an endpoint expecting ordinary Ethernet. It does not explain the condition tested here.

Question 751

The team believes it has resolved this Junos issue: A core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs. Which observation best verifies the specific intended result?

  1. Only authorized static prefixes appear as OSPF externals; management prefixes remain local.
  2. An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0.
  3. The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change.
  4. The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests.

Explanation

Correct Answer

C:

The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change. This checks the relevant result after compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints.

Incorrect Answers

A:

“Only authorized static prefixes appear as OSPF externals; management prefixes remain local” belongs to a separate Interior Gateway Protocols (IGPs) issue: a redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local. It does not explain the condition tested here.

B:

“An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0” belongs to a separate Interior Gateway Protocols (IGPs) issue: a new IPv6 peering uses OSPFv3 on a retired VLAN unit rather than the active routed transit interface. It does not explain the condition tested here.

D:

“The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.

Question 752

Which suggested shortcut would be especially unsafe for this exact situation? BGP peers exchange IPv4 NLRI correctly but a planned IPv6 customer route never appears in inet6.0.

  1. Use multivariable path-selection lab tests before changing MED-based policy.
  2. Assume successful inet IPv4 routes imply that IPv6 NLRI is already negotiated.
  3. Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews.
  4. Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes.

Explanation

Correct Answer

B:

The tempting alternative fails because BGP address-family negotiation controls which IPv4 or IPv6 NLRI can be exchanged independently of session state. The supported action is to enable the intended inet6 family consistently on eligible BGP peers and verify route policy and inet6.0.

Incorrect Answers

A:

That prevention measure relates to two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to an operator tries to make a remote AS prefer one inbound path using LOCAL_PREF that the remote eBGP peer never receives.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer.; it is not the unsafe shortcut described here.

Question 753

A Junos enterprise team investigates this incident: A building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. Which technical explanation most directly identifies the cause or design principle?

  1. Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles.
  2. MVRP distributes VLAN registration information across participating links; a gap can stop propagation.
  3. MVRP registrations can persist where membership state or participation has not been updated consistently.
  4. Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.

Explanation

Correct Answer

A:

Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles. The appropriate response is to inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.

Incorrect Answers

B:

“MVRP distributes VLAN registration information across participating links; a gap can stop propagation” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. It does not explain the condition tested here.

C:

“MVRP registrations can persist where membership state or participation has not been updated consistently” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It does not explain the condition tested here.

D:

“Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough” belongs to a separate Ethernet Switching and Spanning Tree issue: a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. It does not explain the condition tested here.

Question 754

To prevent recurrence of this precise networking failure, which practice should be adopted? An engineer adds advertise-inactive and downstream peers begin receiving a BGP route that loses to an OSPF route locally.

  1. Track every BGP advertise-inactive exception and test cross-protocol route selection.
  2. Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP.
  3. Test path equivalence, forwarding and failure convergence before enabling transit ECMP.
  4. Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes.

Explanation

Correct Answer

A:

Track every BGP advertise-inactive exception and test cross-protocol route selection. This guards against Junos normally exports active routes; advertise-inactive can expose a best BGP candidate that lost to another protocol.

Incorrect Answers

B:

“Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP” belongs to a separate Border Gateway Protocol (BGP) issue: a route-reflector client receives an external destination but lacks the underlay path to the advertised next hop. It does not explain the condition tested here.

C:

“Test path equivalence, forwarding and failure convergence before enabling transit ECMP” belongs to a separate Border Gateway Protocol (BGP) issue: two eBGP sessions over different transports are expected to provide ECMP but only one forwarding next hop appears. It does not explain the condition tested here.

D:

“Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes” belongs to a separate Border Gateway Protocol (BGP) issue: a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. It does not explain the condition tested here.

Question 755

A network change is required for the following specific situation: A receiver port stops getting multicast because IGMP membership was not processed by the access switch after an interface move. Which corrective action is most appropriate?

  1. Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
  2. Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.
  3. Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
  4. Inspect multicast RPF state and the routing table used for source resolution, then correct the underlay or allowed RPF selection.

Explanation

Correct Answer

A:

IGMP reports express receiver interest, and IGMP snooping uses that interest to constrain Layer 2 replication. Verify this by checking that subscribed receivers get the stream without unnecessary flood to ports that did not join.

Incorrect Answers

B:

“Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.

C:

“Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy” belongs to a separate IP Multicast issue: a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. It does not explain the condition tested here.

D:

“Inspect multicast RPF state and the routing table used for source resolution, then correct the underlay or allowed RPF selection” belongs to a separate IP Multicast issue: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It does not explain the condition tested here.

Question 756

To prevent recurrence of this precise networking failure, which practice should be adopted? A backup traffic queue consumes too much buffer and latency-sensitive applications starve during peak bursts.

  1. Keep a documented forwarding-class inventory and test default mappings after service changes.
  2. Plan buffer and shaping rates against provider handoff capacity and expected burst size.
  3. Review queue buffer tradeoffs and regression-test peak loads before tuning schedulers.
  4. Document trusted-marking boundaries and test both matched and unmatched multifield traffic.

Explanation

Correct Answer

C:

Review queue buffer tradeoffs and regression-test peak loads before tuning schedulers. This guards against queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress.

Incorrect Answers

A:

“Keep a documented forwarding-class inventory and test default mappings after service changes” belongs to a separate Class of Service (CoS) issue: a forwarding-class configuration sends critical routing packets to a queue used for bulk backups and adjacency stability degrades under load. It does not explain the condition tested here.

B:

“Plan buffer and shaping rates against provider handoff capacity and expected burst size” belongs to a separate Class of Service (CoS) issue: a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. It does not explain the condition tested here.

D:

“Document trusted-marking boundaries and test both matched and unmatched multifield traffic” belongs to a separate Class of Service (CoS) issue: a security function needs to classify a subset of traffic by source and destination criteria rather than trusted external markings. It does not explain the condition tested here.

Question 757

Which suggested shortcut would be especially unsafe for this exact situation? An iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0.

  1. Lower AS-path length without fixing the unreachable BGP next-hop address.
  2. Test expected best-path behavior before modifying LOCAL_PREF across internal peers.
  3. Test path equivalence, forwarding and failure convergence before enabling transit ECMP.
  4. Record eBGP peer transport depth and endpoint routing in deployment templates.

Explanation

Correct Answer

A:

The tempting alternative fails because BGP route selection first requires the BGP next hop to resolve through the appropriate routing table. The supported action is to restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.

Incorrect Answers

B:

That prevention measure relates to an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to equal candidate BGP routes are visible but no multipath forwarding entry is installed because eligibility or policy differs.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain.; it is not the unsafe shortcut described here.

Question 758

Select THREE complementary corrective, verification, or preventive controls for this scenario: A campus uplink transmits marked video as ordinary data because no behavior-aggregate classifier is attached at ingress.

  1. Apply an approved behavior-aggregate classifier with the intended DSCP-to-class mapping on the real ingress interface.
  2. Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing.
  3. Observed queue counters show voice packets in the designated forwarding class after classification.
  4. Assume any policing rule provides the same paced, buffered behavior as egress shaping.
  5. Test classifier attachment and DSCP mappings on every access and aggregation ingress template.
  6. Configure egress rewriting alone and assume it classifies all incoming traffic into voice queues.

Explanation

Correct Answers

A:

Correction: Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment.

C:

Confirmation: Apply an approved behavior-aggregate classifier with the intended DSCP-to-class mapping on the real ingress interface.

E:

Prevention of recurrence: Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment.

Incorrect Answers

B:

“Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing” is an unsafe response to a different problem: two queues use the same scheduler priority, but the business expects one to always win during contention. It is not a valid fix here.

D:

“Assume any policing rule provides the same paced, buffered behavior as egress shaping” is an unsafe response to a different problem: a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. It is not a valid fix here.

F:

“Configure egress rewriting alone and assume it classifies all incoming traffic into voice queues” does not address Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment.

Question 759

Select THREE complementary corrective, verification, or preventive controls for this scenario: A dual-homed site changes internal LOCAL_PREF but sees no change in the other autonomous system's inbound traffic choice.

  1. Expect a locally set LOCAL_PREF value to propagate unchanged over standard eBGP to another AS.
  2. Assume successful inet IPv4 routes imply that IPv6 NLRI is already negotiated.
  3. Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews.
  4. Select a permitted inbound traffic-engineering mechanism with the provider, such as suitable AS-path prepending or agreed communities.
  5. Assume the shortest AS path must win regardless of any LOCAL_PREF difference.
  6. External peer advertisements show the intended supported attributes and inbound traffic is measured.

Explanation

Correct Answers

C:

Prevention of recurrence: LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors.

D:

Correction: LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors.

F:

Confirmation: Select a permitted inbound traffic-engineering mechanism with the provider, such as suitable AS-path prepending or agreed communities.

Incorrect Answers

A:

“Expect a locally set LOCAL_PREF value to propagate unchanged over standard eBGP to another AS” does not address LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors.

B:

“Assume successful inet IPv4 routes imply that IPv6 NLRI is already negotiated” is an unsafe response to a different problem: a campus router's BGP IPv6 session is Established yet peers advertise only inet unicast family routes. It is not a valid fix here.

E:

“Assume the shortest AS path must win regardless of any LOCAL_PREF difference” is an unsafe response to a different problem: a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops. It is not a valid fix here.

Question 760

The team believes it has resolved this Junos issue: Two newly deployed distribution switches report identical OSPF router IDs, causing inconsistent LSAs in the area. Which observation best verifies the specific intended result?

  1. The remote inet6.0 table learns the intended loopback and reachability testing succeeds.
  2. No router-ID collision appears and OSPF paths stabilize with expected next hops.
  3. An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0.
  4. The preferred primary route wins when healthy and the backup becomes active on a controlled failure.

Explanation

Correct Answer

B:

No router-ID collision appears and OSPF paths stabilize with expected next hops. This checks the relevant result after assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence.

Incorrect Answers

A:

“The remote inet6.0 table learns the intended loopback and reachability testing succeeds” belongs to a separate Interior Gateway Protocols (IGPs) issue: OSPFv3 peering comes up but the desired IPv6 loopback is not in the routing database after a rollout. It does not explain the condition tested here.

C:

“An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. It does not explain the condition tested here.

D:

“The preferred primary route wins when healthy and the backup becomes active on a controlled failure” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.