Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 80

Question 790

The team believes it has resolved this Junos issue: A PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface. Which observation best verifies the specific intended result?

  1. Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow.
  2. The required PIM neighbors appear and downstream join state tracks active interested receivers.
  3. RPF counters and expected (S,G) forwarding stabilize after the route change.
  4. Only the specified source delivers data to receivers of the chosen SSM group.

Explanation

Correct Answer

B:

The required PIM neighbors appear and downstream join state tracks active interested receivers. This checks the relevant result after enable PIM on the approved routed VLAN interface and inspect neighbor and join state.

Incorrect Answers

A:

“Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow” belongs to a separate IP Multicast issue: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It does not explain the condition tested here.

C:

“RPF counters and expected (S,G) forwarding stabilize after the route change” belongs to a separate IP Multicast issue: a redundant network changes the preferred route to the source while packets keep arriving on the other physical link. It does not explain the condition tested here.

D:

“Only the specified source delivers data to receivers of the chosen SSM group” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.

Question 791

A network change is required for the following specific situation: A stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work. Which corrective action is most appropriate?

  1. Refine the relevant multicast policy ranges and inspect forwarding for both permitted and denied groups.
  2. Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
  3. Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.
  4. Compare source-route preference with actual multicast ingress and restore a consistent authorized upstream path.

Explanation

Correct Answer

D:

An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic. Verify this by checking that RPF counters and expected (S,G) forwarding stabilize after the route change.

Incorrect Answers

A:

“Refine the relevant multicast policy ranges and inspect forwarding for both permitted and denied groups” belongs to a separate IP Multicast issue: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It does not explain the condition tested here.

B:

“Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports” belongs to a separate IP Multicast issue: an access VLAN floods every multicast packet because IGMP snooping state was lost during migration. It does not explain the condition tested here.

C:

“Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.

Question 792

Which suggested shortcut would be especially unsafe for this exact situation? A branch wants to enforce a traffic contract on an incoming service flow yet applies policing to an unrelated egress path.

  1. Validate classifier, scheduler map and interface association as a complete CoS chain.
  2. Document trusted-marking boundaries and test both matched and unmatched multifield traffic.
  3. Use an egress shaper at the wrong interface as a substitute for every ingress traffic-contract check.
  4. Audit DSCP preservation and remarking at untrusted edge boundaries.

Explanation

Correct Answer

C:

The tempting alternative fails because a policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress. The supported action is to apply a correctly scoped ingress policer with tested rate and burst values on the relevant flow.

Incorrect Answers

A:

That prevention measure relates to a campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a security function needs to classify a subset of traffic by source and destination criteria rather than trusted external markings.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice.; it is not the unsafe shortcut described here.

Question 793

Which suggested shortcut would be especially unsafe for this exact situation? A dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream.

  1. Maintain representative match and nonmatch tests for filter-based VLAN policies.
  2. Audit edge classifications and apply appropriate BPDU protection on true client-facing ports.
  3. Test private-port isolation and uplink reachability after access topology changes.
  4. Delete all VLANs from every trunk to clear one stale MVRP registration.

Explanation

Correct Answer

D:

The tempting alternative fails because MVRP registrations can persist where membership state or participation has not been updated consistently. The supported action is to inspect registration state and remove stale VLAN membership while preserving necessary registrations.

Incorrect Answers

A:

That prevention measure relates to a campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint.; it is not the unsafe shortcut described here.

C:

“Test private-port isolation and uplink reachability after access topology changes” instead concerns another network scenario: A shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It does not address the requirement here.

Question 794

To prevent recurrence of this precise networking failure, which practice should be adopted? An OSPF neighbor remains Down because the routed transit interface was left passive after a site template rollout.

  1. Classify loopbacks and user-facing links separately from peer links when applying passive templates.
  2. Test one allowed and one forbidden route against each export policy term before deployment.
  3. Document expected external metrics and run primary/backup failover tests during policy changes.
  4. Record both LSDB presence and local RIB installation in OSPF troubleshooting runbooks.

Explanation

Correct Answer

A:

Classify loopbacks and user-facing links separately from peer links when applying passive templates. This guards against making a link passive suppresses OSPF adjacency formation even when its prefix remains eligible for advertisement.

Incorrect Answers

B:

“Test one allowed and one forbidden route against each export policy term before deployment” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated. It does not explain the condition tested here.

C:

“Document expected external metrics and run primary/backup failover tests during policy changes” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.

D:

“Record both LSDB presence and local RIB installation in OSPF troubleshooting runbooks” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability. It does not explain the condition tested here.

Question 795

A Junos enterprise team investigates this incident: Voice packets arrive with DSCP EF but are placed into the best-effort queue after a new access interface template is applied. Which technical explanation most directly identifies the cause or design principle?

  1. Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress.
  2. Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment.
  3. Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract.
  4. A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress.

Explanation

Correct Answer

B:

Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment. The appropriate response is to apply an approved behavior-aggregate classifier with the intended DSCP-to-class mapping on the real ingress interface.

Incorrect Answers

A:

“Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress” belongs to a separate Class of Service (CoS) issue: video gets dropped under congestion despite spare capacity because its queue has a too-small delay buffer. It does not explain the condition tested here.

C:

“Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract” belongs to a separate Class of Service (CoS) issue: a branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. It does not explain the condition tested here.

D:

“A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.

Question 796

To prevent recurrence of this precise networking failure, which practice should be adopted? A switch assigns equal PoE power priority to every port and disconnects an emergency phone before low-priority signage during a power shortage.

  1. Keep a prioritized PoE inventory and test behavior after PSU or stack changes.
  2. Include LLDP-MED capabilities and network-policy TLVs in phone-vendor acceptance testing.
  3. Review LLDP-MED state and phone compliance during access-switch template audits.
  4. Test both tagged phone frames and untagged PC frames during phone-port commissioning.

Explanation

Correct Answer

A:

Keep a prioritized PoE inventory and test behavior after PSU or stack changes. This guards against PoE priority is a tool for allocating scarce power among endpoints when the chassis budget is constrained.

Incorrect Answers

B:

“Include LLDP-MED capabilities and network-policy TLVs in phone-vendor acceptance testing” belongs to a separate IP Telephony Features issue: a newly deployed IP phone joins the data network because the switch does not advertise the intended voice VLAN through LLDP-MED. It does not explain the condition tested here.

C:

“Review LLDP-MED state and phone compliance during access-switch template audits” belongs to a separate IP Telephony Features issue: a powered endpoint detects a Junos switch but fails to negotiate voice prioritization because only ordinary LLDP is enabled. It does not explain the condition tested here.

D:

“Test both tagged phone frames and untagged PC frames during phone-port commissioning” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.

Question 797

Which suggested shortcut would be especially unsafe for this exact situation? Two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result.

  1. Include downstream device count and authentication method in desk-port templates.
  2. Classify interactive and headless endpoint requirements before choosing the access method.
  3. Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding.
  4. Allow the weakest matching authentication method to grant full access regardless of prior EAP outcomes.

Explanation

Correct Answer

D:

The tempting alternative fails because authentication-method precedence and session state can affect which effective authorization takes hold. The supported action is to inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior.

Incorrect Answers

A:

That prevention measure relates to a telephony desk requires multiple authenticated identities while the switch policy allows only one active supplicant.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a captive portal requirement is applied to a headless barcode scanner that has no web browser to follow its redirect.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile.; it is not the unsafe shortcut described here.

Question 798

The team believes it has resolved this Junos issue: A core node shows a missing route while remote LSDBs include the corresponding external LSA after a local policy change. Which observation best verifies the specific intended result?

  1. An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0.
  2. The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change.
  3. The expected prefix becomes active locally while unwanted external prefixes remain filtered.
  4. The backbone receives the intended aggregate and routers can reach all included component subnets.

Explanation

Correct Answer

C:

The expected prefix becomes active locally while unwanted external prefixes remain filtered. This checks the relevant result after compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.

Incorrect Answers

A:

“An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0” belongs to a separate Interior Gateway Protocols (IGPs) issue: a new IPv6 peering uses OSPFv3 on a retired VLAN unit rather than the active routed transit interface. It does not explain the condition tested here.

B:

“The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs. It does not explain the condition tested here.

D:

“The backbone receives the intended aggregate and routers can reach all included component subnets” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus summarization change hides a needed subnet because the configured address range omits it. It does not explain the condition tested here.

Question 799

A Junos enterprise team investigates this incident: A large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits. Which technical explanation most directly identifies the cause or design principle?

  1. Overbroad match conditions can cause unauthorized VLAN steering and affect both security and reachability.
  2. MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.
  3. MVRP registrations can persist where membership state or participation has not been updated consistently.
  4. A private VLAN community allows permitted communication within its community; isolated behavior is stricter.

Explanation

Correct Answer

B:

MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control. The appropriate response is to create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior.

Incorrect Answers

A:

“Overbroad match conditions can cause unauthorized VLAN steering and affect both security and reachability” belongs to a separate Ethernet Switching and Spanning Tree issue: a filter-based VLAN security design uses a rule that catches too many packets and steers legitimate devices into quarantine. It does not explain the condition tested here.

C:

“MVRP registrations can persist where membership state or participation has not been updated consistently” belongs to a separate Ethernet Switching and Spanning Tree issue: a dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream. It does not explain the condition tested here.

D:

“A private VLAN community allows permitted communication within its community; isolated behavior is stricter” belongs to a separate Ethernet Switching and Spanning Tree issue: members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication. It does not explain the condition tested here.

Question 800

A Junos enterprise team investigates this incident: A campus mistakenly enables edge behavior on a switch-to-switch trunk and a loop appears when a backup link activates. Which technical explanation most directly identifies the cause or design principle?

  1. Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink.
  2. Spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections.
  3. MVRP registrations can persist where membership state or participation has not been updated consistently.
  4. Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context.

Explanation

Correct Answer

B:

Spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections. The appropriate response is to remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.

Incorrect Answers

A:

“Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink” belongs to a separate Ethernet Switching and Spanning Tree issue: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It does not explain the condition tested here.

C:

“MVRP registrations can persist where membership state or participation has not been updated consistently” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It does not explain the condition tested here.

D:

“Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.