100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 800
A Junos enterprise team investigates this incident: A campus mistakenly enables edge behavior on a switch-to-switch trunk and a loop appears when a backup link activates. Which technical explanation most directly identifies the cause or design principle?
- Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink.
- Spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections.
- MVRP registrations can persist where membership state or participation has not been updated consistently.
- Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context.
Explanation
Correct Answer
B:Spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections. The appropriate response is to remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
Incorrect Answers
A:“Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink” belongs to a separate Ethernet Switching and Spanning Tree issue: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It does not explain the condition tested here.
C:“MVRP registrations can persist where membership state or participation has not been updated consistently” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It does not explain the condition tested here.
D:“Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.
Question 801
A Junos enterprise team investigates this incident: Two adjacent MSTP switches show different region digests after one has a different VLAN-to-instance map. Which technical explanation most directly identifies the cause or design principle?
- Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles.
- Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.
- MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map.
- Q-in-Q requires deliberate tagging and untagging at service boundaries, with customer tags retained according to the handoff contract.
Explanation
Correct Answer
C:MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map. The appropriate response is to compare complete region configuration on the peers and restore the approved shared MSTP region values.
Incorrect Answers
A:“Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. It does not explain the condition tested here.
B:“Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough” belongs to a separate Ethernet Switching and Spanning Tree issue: a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. It does not explain the condition tested here.
D:“Q-in-Q requires deliberate tagging and untagging at service boundaries, with customer tags retained according to the handoff contract” belongs to a separate Ethernet Switching and Spanning Tree issue: a Q-in-Q service works across transport but the far-end access handoff presents unexpected double tags. It does not explain the condition tested here.
Question 802
The team believes it has resolved this Junos issue: An alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. Which observation best verifies the specific intended result?
- RPF errors stop and the expected multicast stream reaches the subscribed downstream interfaces.
- Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow.
- The required PIM neighbors appear and downstream join state tracks active interested receivers.
- Only the specified source delivers data to receivers of the chosen SSM group.
Explanation
Correct Answer
A:RPF errors stop and the expected multicast stream reaches the subscribed downstream interfaces. This checks the relevant result after inspect multicast RPF state and the routing table used for source resolution, then correct the underlay or allowed RPF selection.
Incorrect Answers
B:“Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.
C:“The required PIM neighbors appear and downstream join state tracks active interested receivers” belongs to a separate IP Multicast issue: a PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface. It does not explain the condition tested here.
D:“Only the specified source delivers data to receivers of the chosen SSM group” belongs to a separate IP Multicast issue: a campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests. It does not explain the condition tested here.
Question 803
The team believes it has resolved this Junos issue: A receiver port stops getting multicast because IGMP membership was not processed by the access switch after an interface move. Which observation best verifies the specific intended result?
- Only the specified source delivers data to receivers of the chosen SSM group.
- Subscribed receivers get the stream without unnecessary flood to ports that did not join.
- Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream.
- The selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow.
Explanation
Correct Answer
B:Subscribed receivers get the stream without unnecessary flood to ports that did not join. This checks the relevant result after inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
Incorrect Answers
A:“Only the specified source delivers data to receivers of the chosen SSM group” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.
C:“Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream” belongs to a separate IP Multicast issue: a one-to-many lecture stream is configured as separate unicast connections and saturates a WAN link to a remote campus. It does not explain the condition tested here.
D:“The selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow” belongs to a separate IP Multicast issue: a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. It does not explain the condition tested here.
Question 804
The team believes it has resolved this Junos issue: An Anycast RP design uses two RP addresses that do not share the intended anycast identity, producing inconsistent joins. Which observation best verifies the specific intended result?
- RPF counters and expected (S,G) forwarding stabilize after the route change.
- A failure of one RP does not strand subscribers and remaining RPs maintain correct multicast source awareness.
- Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream.
- Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow.
Explanation
Correct Answer
B:A failure of one RP does not strand subscribers and remaining RPs maintain correct multicast source awareness. This checks the relevant result after verify anycast RP address and supported source synchronization method across the participating RP nodes.
Incorrect Answers
A:“RPF counters and expected (S,G) forwarding stabilize after the route change” belongs to a separate IP Multicast issue: a stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work. It does not explain the condition tested here.
C:“Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream” belongs to a separate IP Multicast issue: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It does not explain the condition tested here.
D:“Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.
Question 805
The team believes it has resolved this Junos issue: A redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local. Which observation best verifies the specific intended result?
- The remote inet6.0 table learns the intended loopback and reachability testing succeeds.
- An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0.
- Stable Hellos and Full neighbor state persist through repeated protocol interval checks.
- Only authorized static prefixes appear as OSPF externals; management prefixes remain local.
Explanation
Correct Answer
D:Only authorized static prefixes appear as OSPF externals; management prefixes remain local. This checks the relevant result after restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.
Incorrect Answers
A:“The remote inet6.0 table learns the intended loopback and reachability testing succeeds” belongs to a separate Interior Gateway Protocols (IGPs) issue: OSPFv3 peering comes up but the desired IPv6 loopback is not in the routing database after a rollout. It does not explain the condition tested here.
B:“An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0” belongs to a separate Interior Gateway Protocols (IGPs) issue: a new IPv6 peering uses OSPFv3 on a retired VLAN unit rather than the active routed transit interface. It does not explain the condition tested here.
C:“Stable Hellos and Full neighbor state persist through repeated protocol interval checks” belongs to a separate Interior Gateway Protocols (IGPs) issue: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It does not explain the condition tested here.
Question 806
Select THREE complementary corrective, verification, or preventive controls for this scenario: A handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design.
- Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN.
- Assume a green Ethernet link light proves an endpoint has its required operating power.
- Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
- Tagged voice packets retain the intended service class through the access and aggregation paths.
- Include end-to-end marking tests when deploying voice VLANs and new phone models.
- Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power.
Explanation
Correct Answers
C:Correction: Voice VLAN placement and CoS marking are related but separate; correct VLAN tagging does not guarantee priority handling.
D:Confirmation: Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
E:Prevention of recurrence: Voice VLAN placement and CoS marking are related but separate; correct VLAN tagging does not guarantee priority handling.
Incorrect Answers
A:“Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN” does not address voice VLAN placement and CoS marking are related but separate; correct VLAN tagging does not guarantee priority handling.
B:“Assume a green Ethernet link light proves an endpoint has its required operating power” is an unsafe response to a different problem: a phone's LLDP-negotiated power demand exceeds its access port's allocated PoE limit and it repeatedly restarts. It is not a valid fix here.
F:“Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power” is an unsafe response to a different problem: a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget. It is not a valid fix here.
Question 807
Which suggested shortcut would be especially unsafe for this exact situation? A receiver port stops getting multicast because IGMP membership was not processed by the access switch after an interface move.
- Disable IGMP snooping everywhere and assume uncontrolled flooding is equivalent to correct membership delivery.
- Keep an approved multicast group allocation and test boundary enforcement after routing changes.
- Run both allow and deny group tests against multicast policy whenever prefixes are revised.
- Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.
Explanation
Correct Answer
A:The tempting alternative fails because IGMP reports express receiver interest, and IGMP snooping uses that interest to constrain Layer 2 replication. The supported action is to inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
Incorrect Answers
B:That prevention measure relates to a laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route.; it is not the unsafe shortcut described here.
Question 808
A network change is required for the following specific situation: A VSTP network intended to send voice and data VLANs over different active paths instead blocks both on the same uplink. Which corrective action is most appropriate?
- Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement.
- Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.
- Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
- Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop.
Explanation
Correct Answer
A:VSTP provides per-VLAN spanning-tree behavior for compatibility and path control when the design and platform support it. Verify this by checking that selected voice and data VLANs use the approved active links without loops.
Incorrect Answers
B:“Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity” belongs to a separate Ethernet Switching and Spanning Tree issue: a private VLAN isolated endpoint reaches the local gateway but cannot access a peer service that should be shared via a permitted promiscuous port. It does not explain the condition tested here.
C:“Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.
D:“Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. It does not explain the condition tested here.
Question 809
Which suggested shortcut would be especially unsafe for this exact situation? Customer traffic emerges with the provider service tag still attached and is rejected by an endpoint expecting ordinary Ethernet.
- Assume every endpoint supports stacked 802.1Q tags even when the customer ordered a single-tagged handoff.
- Check policy coverage and unintended-match cases before activating filter-based steering.
- Test each critical VLAN's root bridge and forwarding path after VSTP updates.
- Version-control MSTP name, revision and VLAN mapping as one change unit.
Explanation
Correct Answer
A:The tempting alternative fails because Q-in-Q requires deliberate tagging and untagging at service boundaries, with customer tags retained according to the handoff contract. The supported action is to inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation.
Incorrect Answers
B:That prevention measure relates to an ingress classification filter for one terminal type inadvertently redirects other hosts using the same uplink.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree.; it is not the unsafe shortcut described here.
D:That prevention measure relates to two adjacent MSTP switches show different region digests after one has a different VLAN-to-instance map.; it is not the unsafe shortcut described here.
Question 810
A network change is required for the following specific situation: An IPv6 route learned through OSPFv3 is absent from the forwarding table because a more preferred static route covers the same prefix. Which corrective action is most appropriate?
- Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.
- Inspect inet6.0 route detail and route preferences before changing OSPFv3 neighbor configuration.
- Assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence.
- Inspect the active local default and export term conditions; match only the authorized static default source.
Explanation
Correct Answer
B:Protocol route advertisement and active-route selection are separate; lower route preference can select a non-OSPF candidate. Verify this by checking that the team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency.
Incorrect Answers
A:“Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability. It does not explain the condition tested here.
C:“Assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence” belongs to a separate Interior Gateway Protocols (IGPs) issue: two newly deployed distribution switches report identical OSPF router IDs, causing inconsistent LSAs in the area. It does not explain the condition tested here.
D:“Inspect the active local default and export term conditions; match only the authorized static default source” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch default-route injection stops after a policy matches OSPF-learned routes instead of the intended local static. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests