100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 950
Which suggested shortcut would be especially unsafe for this exact situation? An edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams.
- Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
- Monitor IGMP membership churn and snooping state when moving clients between VLANs.
- Maintain consistent RP mappings and failover tests across multicast routers.
- Replace all multicast group filters with a broad permit because at least one approved stream failed.
Explanation
Correct Answer
D:The tempting alternative fails because policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked. The supported action is to refine the relevant multicast policy ranges and inspect forwarding for both permitted and denied groups.
Incorrect Answers
A:That prevention measure relates to a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a receiver port stops getting multicast because IGMP membership was not processed by the access switch after an interface move.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point.; it is not the unsafe shortcut described here.
Question 951
A network change is required for the following specific situation: An OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability. Which corrective action is most appropriate?
- Compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints.
- Compare OSPF interface timers and align the two peers to approved Hello and dead values.
- Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.
- Remove passive behavior only from the approved router-to-router transit link and check Hello and neighbor states.
Explanation
Correct Answer
C:Local import policy can affect installed route visibility independently of the remote origination of LSAs. Verify this by checking that the expected prefix becomes active locally while unwanted external prefixes remain filtered.
Incorrect Answers
A:“Compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs. It does not explain the condition tested here.
B:“Compare OSPF interface timers and align the two peers to approved Hello and dead values” belongs to a separate Interior Gateway Protocols (IGPs) issue: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It does not explain the condition tested here.
D:“Remove passive behavior only from the approved router-to-router transit link and check Hello and neighbor states” belongs to a separate Interior Gateway Protocols (IGPs) issue: a distribution node learns connected subnets but never sends Hello packets on its OSPF transit port due to passive-interface policy. It does not explain the condition tested here.
Question 952
Select THREE complementary corrective, verification, or preventive controls for this scenario: A switch assigns a misconfigured laptop with incorrect EAP credentials to a VLAN intended only for devices that never attempt 802.1X.
- A nonresponding guest gets its intended limited VLAN while invalid credentials never receive guest privilege.
- Check authentication result classification and map the rejected user to an appropriate deny or reject response.
- Treat a MAC address alone as cryptographic proof of device ownership and elevate access privileges.
- Document and test EAP timeout, explicit rejection and server-unavailable cases separately.
- Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event.
- Require the scanner to open a login web page even though the device has no web client.
Explanation
Correct Answers
A:Confirmation: Check authentication result classification and map the rejected user to an appropriate deny or reject response.
B:Correction: Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.
D:Prevention of recurrence: Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.
Incorrect Answers
C:“Treat a MAC address alone as cryptographic proof of device ownership and elevate access privileges” is an unsafe response to a different problem: a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. It is not a valid fix here.
E:“Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event” does not address guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.
F:“Require the scanner to open a login web page even though the device has no web client” is an unsafe response to a different problem: a noninteractive sensor is trapped in captive-portal onboarding because operators selected browser authentication for all endpoints. It is not a valid fix here.
Question 953
A network change is required for the following specific situation: A campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route. Which corrective action is most appropriate?
- Refine the relevant multicast policy ranges and inspect forwarding for both permitted and denied groups.
- Verify anycast RP address and supported source synchronization method across the participating RP nodes.
- Enable PIM on the approved routed VLAN interface and inspect neighbor and join state.
- Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
Explanation
Correct Answer
D:Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic. Verify this by checking that the selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow.
Incorrect Answers
A:“Refine the relevant multicast policy ranges and inspect forwarding for both permitted and denied groups” belongs to a separate IP Multicast issue: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It does not explain the condition tested here.
B:“Verify anycast RP address and supported source synchronization method across the participating RP nodes” belongs to a separate IP Multicast issue: a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it. It does not explain the condition tested here.
C:“Enable PIM on the approved routed VLAN interface and inspect neighbor and join state” belongs to a separate IP Multicast issue: a new L3 VLAN permits unicast connectivity but the PIM Hello adjacency remains absent on the active path. It does not explain the condition tested here.
Question 954
The team believes it has resolved this Junos issue: A campus mistakenly enables edge behavior on a switch-to-switch trunk and a loop appears when a backup link activates. Which observation best verifies the specific intended result?
- Two customers can use overlapping inner VLAN numbers without traffic mixing on the transport.
- The redundant topology converges without sustained broadcast loops during link-failure testing.
- Isolated clients reach the shared service but cannot communicate laterally with other isolated clients.
- Two isolated tenant ports cannot reach each other but can reach the permitted gateway uplink.
Explanation
Correct Answer
B:The redundant topology converges without sustained broadcast loops during link-failure testing. This checks the relevant result after remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
Incorrect Answers
A:“Two customers can use overlapping inner VLAN numbers without traffic mixing on the transport” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.
C:“Isolated clients reach the shared service but cannot communicate laterally with other isolated clients” belongs to a separate Ethernet Switching and Spanning Tree issue: a private VLAN isolated endpoint reaches the local gateway but cannot access a peer service that should be shared via a permitted promiscuous port. It does not explain the condition tested here.
D:“Two isolated tenant ports cannot reach each other but can reach the permitted gateway uplink” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It does not explain the condition tested here.
Question 955
Which suggested shortcut would be especially unsafe for this exact situation? An IPv6 transit prefix is hidden because its next-hop address is absent from the correct IPv6 routing table.
- Validate every route-reflector client and failover path in topology inventory before conversion.
- Point to a successful IPv4 traceroute as sufficient proof an IPv6 BGP next hop resolves.
- Test expected best-path behavior before modifying LOCAL_PREF across internal peers.
- Validate all required BGP address families during dual-stack peer commissioning.
Explanation
Correct Answer
B:The tempting alternative fails because BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops. The supported action is to check IPv6 next-hop reachability and inet6.0, then install a permitted IPv6 underlay route or correct next-hop policy.
Incorrect Answers
A:That prevention measure relates to a route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a campus router's BGP IPv6 session is Established yet peers advertise only inet unicast family routes.; it is not the unsafe shortcut described here.
Question 956
Which suggested shortcut would be especially unsafe for this exact situation? An industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service.
- Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance.
- Mark every unknown MAC as trusted and give it unrestricted data-VLAN access.
- Classify interactive and headless endpoint requirements before choosing the access method.
- Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding.
Explanation
Correct Answer
B:The tempting alternative fails because MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X. The supported action is to configure supported MAC RADIUS under least-privilege policy and register the device MAC with the approved service.
Incorrect Answers
A:That prevention measure relates to guest users on an EX switch see no captive login page because browser HTTP redirects are not being applied on the intended VLAN.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a captive portal requirement is applied to a headless barcode scanner that has no web browser to follow its redirect.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend.; it is not the unsafe shortcut described here.
Question 957
The team believes it has resolved this Junos issue: A finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. Which observation best verifies the specific intended result?
- Control-plane-related traffic receives the expected queue treatment under simulated load.
- Only traffic meeting the defined match receives the intended queue and packet loss priority.
- Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.
- Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses.
Explanation
Correct Answer
D:Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses. This checks the relevant result after assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.
Incorrect Answers
A:“Control-plane-related traffic receives the expected queue treatment under simulated load” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.
B:“Only traffic meeting the defined match receives the intended queue and packet loss priority” belongs to a separate Class of Service (CoS) issue: an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It does not explain the condition tested here.
C:“Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses” belongs to a separate Class of Service (CoS) issue: a branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. It does not explain the condition tested here.
Question 958
Which suggested shortcut would be especially unsafe for this exact situation? A finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy.
- Differentiate ingress policing from egress shaping when designing bandwidth controls.
- Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing.
- Test marking, PLP assignment and drop policy together rather than checking only DSCP fields.
- Audit DSCP preservation and remarking at untrusted edge boundaries.
Explanation
Correct Answer
B:The tempting alternative fails because scheduler priority and bandwidth allocation affect queuing service but must balance fairness and starvation concerns. The supported action is to assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.
Incorrect Answers
A:That prevention measure relates to a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice.; it is not the unsafe shortcut described here.
Question 959
Which suggested shortcut would be especially unsafe for this exact situation? A desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN.
- Review LLDP-MED state and phone compliance during access-switch template audits.
- Put the phone and PC on one unrestricted VLAN to avoid checking voice VLAN tagging.
- Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
- Synchronize switchport moves with maintained emergency location records.
Explanation
Correct Answer
B:The tempting alternative fails because voice/data split depends on compatible VLAN membership, accepted 802.1Q tagging and endpoint network policy. The supported action is to configure an approved voice VLAN on the port while keeping the PC data VLAN constrained.
Incorrect Answers
A:That prevention measure relates to a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an IP phone uses the wrong location information for emergency response after a switch move.; it is not the unsafe shortcut described here.
Question 960
A network change is required for the following specific situation: A legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. Which corrective action is most appropriate?
- Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.
- Map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated.
- Inspect registration state and remove stale VLAN membership while preserving necessary registrations.
- Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement.
Explanation
Correct Answer
D:VSTP provides per-VLAN spanning-tree behavior for compatibility and path control when the design and platform support it. Verify this by checking that selected voice and data VLANs use the approved active links without loops.
Incorrect Answers
A:“Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule” belongs to a separate Ethernet Switching and Spanning Tree issue: a policy-based VLAN filter moves matching device traffic to a quarantine VLAN but a rule fails to match the intended MAC or packet fields. It does not explain the condition tested here.
B:“Map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated” belongs to a separate Ethernet Switching and Spanning Tree issue: members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication. It does not explain the condition tested here.
C:“Inspect registration state and remove stale VLAN membership while preserving necessary registrations” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests