100% Latest & Updated Microsoft AZ-700 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 310
A VPN Gateway is provisioned but its resource cannot be placed in the intended VNet. The architecture uses this design: Create a valid dedicated GatewaySubnet inside the target VNet. Which configuration should the engineer apply to implement it?
- Set the connection's route table association and propagation labels correctly
- Use supported gateway SKU and enable FastPath on the eligible connection
- Add a correctly named GatewaySubnet of supported prefix size before deployment
- Set matching encryption, integrity, DH and PFS parameters where supported
Explanation
Correct Answer
C:Add a correctly named GatewaySubnet of supported prefix size before deployment is the operational configuration for create a valid dedicated gatewaysubnet inside the target vnet. The acceptance test is to confirm gateway deployment completes and the correct subnet attachment is shown.
Incorrect Answers
A:Set the connection's route table association and propagation labels correctly is a concrete step for review the virtual wan vnet connection association and propagation settings. Here the selected design is create a valid dedicated gatewaysubnet inside the target vnet, which instead requires add a correctly named gatewaysubnet of supported prefix size before deployment.
B:Use supported gateway SKU and enable FastPath on the eligible connection is a concrete step for consider expressroute fastpath on supported gateway and circuit combinations. Here the selected design is create a valid dedicated gatewaysubnet inside the target vnet, which instead requires add a correctly named gatewaysubnet of supported prefix size before deployment.
D:Set matching encryption, integrity, DH and PFS parameters where supported is a concrete step for align both ends on a supported ike/ipsec policy. Here the selected design is create a valid dedicated gatewaysubnet inside the target vnet, which instead requires add a correctly named gatewaysubnet of supported prefix size before deployment.
Question 311
A VPN Gateway is provisioned but its resource cannot be placed in the intended VNet. After the team applies this change—add a correctly named GatewaySubnet of supported prefix size before deployment—which validation best proves the intended result?
- Confirm gateway deployment completes and the correct subnet attachment is shown
- Compare SKU-supported gateway and routing features to the actual use case
- Inspect negotiated selectors and confirm required prefixes pass
- Resolve a private hostname after connection and confirm its private answer
Explanation
Correct Answer
A:Confirm gateway deployment completes and the correct subnet attachment is shown directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether gatewaySubnet naming or sizing does not meet requirements.
Incorrect Answers
B:Compare SKU-supported gateway and routing features to the actual use case. This concerns simple isolated site-to-site vpn connections without advanced transitive features. Instead, confirm gateway deployment completes and the correct subnet attachment is shown.
C:Inspect negotiated selectors and confirm required prefixes pass. This concerns a legacy on-premises IPSEC device only supports policy-based traffic selectors. Instead, confirm gateway deployment completes and the correct subnet attachment is shown.
D:Resolve a private hostname after connection and confirm its private answer. This is relevant when an employee is connected to azure vpn but private DNS names are not resolving. Instead, confirm gateway deployment completes and the correct subnet attachment is shown.
Question 312
A VPN Gateway is provisioned but its resource cannot be placed in the intended VNet. During acceptance testing, gateway deployment reports a missing or invalid subnet. Which underlying configuration problem best explains the symptom?
- The circuit tier does not permit the requested geographic reach
- GatewaySubnet naming or sizing does not meet requirements
- Private ExpressRoute transport alone does not provide encryption
- Entra issuer or audience configuration does not match the client token
Explanation
Correct Answer
B:GatewaySubnet naming or sizing does not meet requirements explains the observed failure: gateway deployment reports a missing or invalid subnet. Correct the design by using create a valid dedicated GatewaySubnet inside the target VNet, implemented through add a correctly named GatewaySubnet of supported prefix size before deployment.
Incorrect Answers
A:The circuit tier does not permit the requested geographic reach. This concerns expressroute connectivity between distant geopolitical regions. Here, gatewaySubnet naming or sizing does not meet requirements.
C:Private ExpressRoute transport alone does not provide encryption. This is relevant when a private circuit but also requires cryptographic encryption in transit. Here, gatewaySubnet naming or sizing does not meet requirements.
D:Entra issuer or audience configuration does not match the client token. This is relevant when a p2s gateway is configured but a user receives invalid-signature token errors. Here, gatewaySubnet naming or sizing does not meet requirements.
Question 313
A branch uses two different internet providers and wants VPN failover. Which Azure networking design most directly satisfies this requirement?
- Configure both primary and secondary BGP peering connections
- Provision a separate ExpressRoute circuit in a distinct peering location
- Use redundant site-to-site VPN connections over separate ISP endpoints
- Create a local network gateway with correct site address and prefixes
Explanation
Correct Answer
C:Use redundant site-to-site VPN connections over separate ISP endpoints addresses the topology, access or delivery requirement in the scenario. Apply it by configure independent local network gateways/connections for both provider paths; confirm by disconnect one ISP and verify traffic can use the remaining tunnel.
Incorrect Answers
A:Configure both primary and secondary BGP peering connections. This concerns providing redundant paths through two independent peering sessions. Instead, use redundant site-to-site VPN connections over separate ISP endpoints.
B:Provision a separate ExpressRoute circuit in a distinct peering location. This concerns disaster recovery if its primary ExpressRoute circuit fails. Instead, use redundant site-to-site VPN connections over separate ISP endpoints.
D:Create a local network gateway with correct site address and prefixes. This concerns being represented in Azure. Instead, use redundant site-to-site VPN connections over separate ISP endpoints.
Question 314
A branch uses two different internet providers and wants VPN failover. The architecture uses this design: Use redundant site-to-site VPN connections over separate ISP endpoints. Which configuration should the engineer apply to implement it?
- Configure peer ASN/BGP addresses and BGP on the connection
- Configure independent local network gateways/connections for both provider paths
- Configure Microsoft peering BGP and route filtering as required
- Configure the P2S tunnel type and matching VPN client support
Explanation
Correct Answer
B:Configure independent local network gateways/connections for both provider paths is the operational configuration for use redundant site-to-site vpn connections over separate isp endpoints. The acceptance test is to disconnect one ISP and verify traffic can use the remaining tunnel.
Incorrect Answers
A:Configure peer ASN/BGP addresses and BGP on the connection is a concrete step for enable bgp with supported gateway and customer edge configuration. Here the selected design is use redundant site-to-site vpn connections over separate isp endpoints, which instead requires configure independent local network gateways/connections for both provider paths.
C:Configure Microsoft peering BGP and route filtering as required is a concrete step for choose microsoft peering only when its supported service requirements apply. Here the selected design is use redundant site-to-site vpn connections over separate isp endpoints, which instead requires configure independent local network gateways/connections for both provider paths.
D:Configure the P2S tunnel type and matching VPN client support is a concrete step for select supported openvpn or ikev2 according to platform and auth requirements. Here the selected design is use redundant site-to-site vpn connections over separate isp endpoints, which instead requires configure independent local network gateways/connections for both provider paths.
Question 315
A branch uses two different internet providers and wants VPN failover. After the team applies this change—configure independent local network gateways/connections for both provider paths—which validation best proves the intended result?
- Disconnect one ISP and verify traffic can use the remaining tunnel
- Import the profile into the correct client and verify endpoint settings
- Validate both gateway instances and test traffic continuity during a failover
- Compare measured tunnel throughput and configured scale units
Explanation
Correct Answer
A:Disconnect one ISP and verify traffic can use the remaining tunnel directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether only one usable ISP-to-Azure tunnel path exists.
Incorrect Answers
B:Import the profile into the correct client and verify endpoint settings. This concerns a user requests a p2s vpn configuration but the client remains unable to import the settings. Here, disconnect one ISP and verify traffic can use the remaining tunnel.
C:Validate both gateway instances and test traffic continuity during a failover. This concerns avoiding dropping traffic when azure performs gateway maintenance. Here, disconnect one ISP and verify traffic can use the remaining tunnel.
D:Compare measured tunnel throughput and configured scale units. This concerns branch bandwidth requirements exceed the default hub vpn capacity. Here, disconnect one ISP and verify traffic can use the remaining tunnel.
Question 316
A branch uses two different internet providers and wants VPN failover. During acceptance testing, a single carrier outage disconnects the branch entirely. Which underlying configuration problem best explains the symptom?
- No ExpressRoute gateway-to-circuit connection exists in the hub
- Only one usable ISP-to-Azure tunnel path exists
- The chosen tunnel protocol or client is unsupported for that platform
- A Basic Virtual WAN SKU was selected for Standard-only features
Explanation
Correct Answer
B:Only one usable ISP-to-Azure tunnel path exists explains the observed failure: a single carrier outage disconnects the branch entirely. Correct the design by using use redundant site-to-site VPN connections over separate ISP endpoints, implemented through configure independent local network gateways/connections for both provider paths.
Incorrect Answers
A:No ExpressRoute gateway-to-circuit connection exists in the hub. This concerns private expressroute access to its global virtual wan topology. Here, only one usable ISP-to-Azure tunnel path exists.
C:The chosen tunnel protocol or client is unsupported for that platform. This concerns using an approved tunnel protocol for mobile remote-user connectivity. Here, only one usable ISP-to-Azure tunnel path exists.
D:A Basic Virtual WAN SKU was selected for Standard-only features. This concerns simple isolated site-to-site vpn connections without advanced transitive features. Here, only one usable ISP-to-Azure tunnel path exists.
Question 317
A company is moving its site-to-site tunnel to a different on-premises public address. Which TWO listed choices identify the suitable Azure design and the concrete configuration required to implement it? (Choose TWO.)
- Update the corresponding local network gateway public IP endpoint
- Create the virtual hub ExpressRoute gateway and attach the authorized circuit
- Consider ExpressRoute FastPath on supported gateway and circuit combinations
- Change the local network gateway's gateway IP and coordinate remote settings
- Enable BGP with supported gateway and customer edge configuration
Explanation
Correct Answers
A:Update the corresponding local network gateway public IP endpoint addresses the topology, access or delivery requirement in the scenario. Apply it by change the local network gateway's gateway IP and coordinate remote settings; confirm by inspect new IKE association source and confirm the connection becomes Connected.
D:Change the local network gateway's gateway IP and coordinate remote settings is the operational configuration for update the corresponding local network gateway public ip endpoint. The acceptance test is to inspect new IKE association source and confirm the connection becomes Connected.
Incorrect Answers
B:Create the virtual hub ExpressRoute gateway and attach the authorized circuit is a concrete step for add an expressroute gateway and circuit connection to an eligible virtual hub. Here the selected design is update the corresponding local network gateway public ip endpoint, which instead requires change the local network gateway's gateway ip and coordinate remote settings.
C:Consider ExpressRoute FastPath on supported gateway and circuit combinations. This concerns an Azure VNet gateway that sends applicable traffic directly over the ExpressRoute data path for better throughput. Instead, update the corresponding local network gateway public IP endpoint.
E:Enable BGP with supported gateway and customer edge configuration. This concerns advertising and learn routes dynamically across a routed VPN. Instead, update the corresponding local network gateway public IP endpoint.
Question 318
A company is moving its site-to-site tunnel to a different on-premises public address. The architecture uses this design: Update the corresponding local network gateway public IP endpoint. Which configuration should the engineer apply to implement it?
- Create a User VPN configuration and associate it with the virtual hub User VPN gateway
- Change the local network gateway's gateway IP and coordinate remote settings
- Create the virtual hub ExpressRoute gateway and attach the authorized circuit
- Enable gateway diagnostic categories and review connection events
Explanation
Correct Answer
B:Change the local network gateway's gateway IP and coordinate remote settings is the operational configuration for update the corresponding local network gateway public ip endpoint. The acceptance test is to inspect new IKE association source and confirm the connection becomes Connected.
Incorrect Answers
A:Create a User VPN configuration and associate it with the virtual hub User VPN gateway is a concrete step for add a point-to-site user vpn gateway to the virtual wan hub. Here the selected design is update the corresponding local network gateway public ip endpoint, which instead requires change the local network gateway's gateway ip and coordinate remote settings.
C:Create the virtual hub ExpressRoute gateway and attach the authorized circuit is a concrete step for add an expressroute gateway and circuit connection to an eligible virtual hub. Here the selected design is update the corresponding local network gateway public ip endpoint, which instead requires change the local network gateway's gateway ip and coordinate remote settings.
D:Enable gateway diagnostic categories and review connection events is a concrete step for use vpn gateway diagnostic logs and tunnel metrics. Here the selected design is update the corresponding local network gateway public ip endpoint, which instead requires change the local network gateway's gateway ip and coordinate remote settings.
Question 319
A company is moving its site-to-site tunnel to a different on-premises public address. After the team applies this change—change the local network gateway's gateway IP and coordinate remote settings—which validation best proves the intended result?
- Inspect effective hub routes and simulate allowed and disallowed paths
- Connect a pilot client and verify hub-connected VNet access
- Inspect BGP learned routes and test a newly advertised prefix
- Inspect new IKE association source and confirm the connection becomes Connected
Explanation
Correct Answer
D:Inspect new IKE association source and confirm the connection becomes Connected directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether the local network gateway still references the old endpoint.
Incorrect Answers
A:Inspect effective hub routes and simulate allowed and disallowed paths. This concerns controlled inter-hub route propagation. Instead, inspect new IKE association source and confirm the connection becomes Connected.
B:Connect a pilot client and verify hub-connected VNet access. This concerns remote employees need user vpn access through the managed global wan. Instead, inspect new IKE association source and confirm the connection becomes Connected.
C:Inspect BGP learned routes and test a newly advertised prefix. This concerns advertising and learn routes dynamically across a routed vpn. Instead, inspect new IKE association source and confirm the connection becomes Connected.
Question 320
A company is moving its site-to-site tunnel to a different on-premises public address. During acceptance testing, azure tries to negotiate with the retired branch IP. Which underlying configuration problem best explains the symptom?
- P2S client pool overlaps local or enterprise address space
- Point-to-site address pool or gateway P2S configuration is missing
- The failure lies in BGP or gateway linkage rather than circuit resource existence
- The local network gateway still references the old endpoint
Explanation
Correct Answer
D:The local network gateway still references the old endpoint explains the observed failure: azure tries to negotiate with the retired branch IP. Correct the design by using update the corresponding local network gateway public IP endpoint, implemented through change the local network gateway's gateway IP and coordinate remote settings.
Incorrect Answers
A:P2S client pool overlaps local or enterprise address space. This concerns p2s vpn clients receive addresses overlapping their home office lan. Here, the local network gateway still references the old endpoint.
B:Point-to-site address pool or gateway P2S configuration is missing. This concerns remote consultants require per-user encrypted vpn access without maintaining a site router. Here, the local network gateway still references the old endpoint.
C:The failure lies in BGP or gateway linkage rather than circuit resource existence. This is relevant when a team is troubleshooting a circuit that is not passing traffic after handoff. Here, the local network gateway still references the old endpoint.
Designing and Implementing Microsoft Azure Networking Solutions (AZ-700) Practice Tests