100% Latest & Updated Microsoft AZ-700 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 750
A Private Link Service producer must publish a service to multiple consumers through one approved frontend. The architecture uses this design: Attach Private Link Service to the supported internal Standard Load Balancer frontend. Which configuration should the engineer apply to implement it?
- Enable service endpoint and add the specific subnet to allowed network rules
- Configure provider-side frontend and NAT IP configuration for the service
- Recreate or correctly configure the endpoint with target resource ID and subresource
- Inspect service endpoint and policy association properties for both subnets
Explanation
Correct Answer
B:Configure provider-side frontend and NAT IP configuration for the service is the operational configuration for attach private link service to the supported internal standard load balancer frontend. The acceptance test is to create two approved consumer private endpoints and verify backend access.
Incorrect Answers
A:Enable service endpoint and add the specific subnet to allowed network rules is a concrete step for use service endpoint-based virtual network access rules on the storage account. Here the selected design is attach private link service to the supported internal standard load balancer frontend, which instead requires configure provider-side frontend and nat ip configuration for the service.
C:Recreate or correctly configure the endpoint with target resource ID and subresource is a concrete step for correct the private endpoint target resource before using it. Here the selected design is attach private link service to the supported internal standard load balancer frontend, which instead requires configure provider-side frontend and nat ip configuration for the service.
D:Inspect service endpoint and policy association properties for both subnets is a concrete step for apply the policy to the exact production subnet and verify service endpoint enabled. Here the selected design is attach private link service to the supported internal standard load balancer frontend, which instead requires configure provider-side frontend and nat ip configuration for the service.
Question 751
A Private Link Service producer must publish a service to multiple consumers through one approved frontend. After the team applies this change—configure provider-side frontend and NAT IP configuration for the service—which validation best proves the intended result?
- Resolve service FQDN to private IP and confirm private route
- Test deployment into approved and disallowed locations
- Test access from allowed and disallowed subnets
- Create two approved consumer private endpoints and verify backend access
Explanation
Correct Answer
D:Create two approved consumer private endpoints and verify backend access directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether private Link Service visibility, NAT capacity or approval is incomplete.
Incorrect Answers
A:Resolve service FQDN to private IP and confirm private route. This concerns all paas connections to remain on exclusively private addresses. Instead, create two approved consumer private endpoints and verify backend access.
B:Test deployment into approved and disallowed locations. This concerns restricting creation of private endpoints to designated subnet boundaries. Instead, create two approved consumer private endpoints and verify backend access.
C:Test access from allowed and disallowed subnets. This concerns allowing only clients from a designated application subnet. Instead, create two approved consumer private endpoints and verify backend access.
Question 752
A Private Link Service producer must publish a service to multiple consumers through one approved frontend. During acceptance testing, only the first consumer can connect to the service. Which underlying configuration problem best explains the symptom?
- Virtual network rule or service endpoint is not configured
- Only development's subnet has the service endpoint policy attached
- No effective service endpoint policy restricts target accounts
- Private Link Service visibility, NAT capacity or approval is incomplete
Explanation
Correct Answer
D:Private Link Service visibility, NAT capacity or approval is incomplete explains the observed failure: only the first consumer can connect to the service. Correct the design by using attach Private Link Service to the supported internal Standard Load Balancer frontend, implemented through configure provider-side frontend and NAT IP configuration for the service.
Incorrect Answers
A:Virtual network rule or service endpoint is not configured. This concerns azure SQL service endpoint support for a supported SQL deployment. Here, private Link Service visibility, NAT capacity or approval is incomplete.
B:Only development's subnet has the service endpoint policy attached. This concerns a service endpoint policy works in development but not in the production subnet. Here, private Link Service visibility, NAT capacity or approval is incomplete.
C:No effective service endpoint policy restricts target accounts. This concerns limit which storage accounts a subnet can reach over service endpoints. Here, private Link Service visibility, NAT capacity or approval is incomplete.
Question 753
A private endpoint service uses a FQDN required for TLS SNI validation. Which Azure networking design most directly satisfies this requirement?
- Use an Azure SQL Database Private Endpoint with correct subresource
- Apply an Azure Storage service endpoint policy to the subnet
- Keep the original service hostname while resolving it to the private IP
- Enable a Microsoft.Storage virtual network service endpoint
Explanation
Correct Answer
C:Keep the original service hostname while resolving it to the private IP addresses the topology, access or delivery requirement in the scenario. Apply it by configure private DNS records for the service's supported hostname, not a raw IP alias; confirm by test HTTPS with the service FQDN and validate its certificate.
Incorrect Answers
A:Use an Azure SQL Database Private Endpoint with correct subresource. This concerns being reachable privately from an application VNet. Instead, keep the original service hostname while resolving it to the private IP.
B:Apply an Azure Storage service endpoint policy to the subnet. This concerns limit which storage accounts a subnet can reach over service endpoints. Instead, keep the original service hostname while resolving it to the private IP.
D:Enable a Microsoft.Storage virtual network service endpoint. This concerns a higher-trust path to Azure Storage while retaining the service's public endpoint. Instead, keep the original service hostname while resolving it to the private IP.
Question 754
A private endpoint service uses a FQDN required for TLS SNI validation. The architecture uses this design: Keep the original service hostname while resolving it to the private IP. Which configuration should the engineer apply to implement it?
- Enable the Storage service endpoint on the subnet and allow the subnet in storage firewall rules
- Create the private endpoint and DNS integration, then restrict public access
- Configure private DNS records for the service's supported hostname, not a raw IP alias
- Create private endpoint connection to the SQL server and approve it
Explanation
Correct Answer
C:Configure private DNS records for the service's supported hostname, not a raw IP alias is the operational configuration for keep the original service hostname while resolving it to the private ip. The acceptance test is to test HTTPS with the service FQDN and validate its certificate.
Incorrect Answers
A:Enable the Storage service endpoint on the subnet and allow the subnet in storage firewall rules is a concrete step for enable a microsoft.storage virtual network service endpoint. Here the selected design is keep the original service hostname while resolving it to the private ip, which instead requires configure private dns records for the service's supported hostname, not a raw ip alias.
B:Create the private endpoint and DNS integration, then restrict public access is a concrete step for choose private endpoint rather than service endpoint for private ip requirements. Here the selected design is keep the original service hostname while resolving it to the private ip, which instead requires configure private dns records for the service's supported hostname, not a raw ip alias.
D:Create private endpoint connection to the SQL server and approve it is a concrete step for use an azure sql database private endpoint with correct subresource. Here the selected design is keep the original service hostname while resolving it to the private ip, which instead requires configure private dns records for the service's supported hostname, not a raw ip alias.
Question 755
A private endpoint service uses a FQDN required for TLS SNI validation. After the team applies this change—configure private DNS records for the service's supported hostname, not a raw IP alias—which validation best proves the intended result?
- Test HTTPS with the service FQDN and validate its certificate
- Test deployment into approved and disallowed locations
- Test connection to an allowed and forbidden storage account
- Test access from allowed and disallowed subnets
Explanation
Correct Answer
A:Test HTTPS with the service FQDN and validate its certificate directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether the client bypassed the certificate's expected service hostname.
Incorrect Answers
B:Test deployment into approved and disallowed locations. This concerns restricting creation of private endpoints to designated subnet boundaries. Instead, test HTTPS with the service FQDN and validate its certificate.
C:Test connection to an allowed and forbidden storage account. This concerns limit which storage accounts a subnet can reach over service endpoints. Instead, test HTTPS with the service FQDN and validate its certificate.
D:Test access from allowed and disallowed subnets. This concerns allowing only clients from a designated application subnet. Instead, test HTTPS with the service FQDN and validate its certificate.
Question 756
A private endpoint service uses a FQDN required for TLS SNI validation. During acceptance testing, tLS fails when applications use the bare private endpoint address. Which underlying configuration problem best explains the symptom?
- A service endpoint was chosen for a requirement that needs Private Link
- The client bypassed the certificate's expected service hostname
- No effective service endpoint policy restricts target accounts
- Storage firewall VNet rule or service endpoint configuration is missing
Explanation
Correct Answer
B:The client bypassed the certificate's expected service hostname explains the observed failure: tLS fails when applications use the bare private endpoint address. Correct the design by using keep the original service hostname while resolving it to the private IP, implemented through configure private DNS records for the service's supported hostname, not a raw IP alias.
Incorrect Answers
A:A service endpoint was chosen for a requirement that needs Private Link. This concerns all paas connections to remain on exclusively private addresses. Here, the client bypassed the certificate's expected service hostname.
C:No effective service endpoint policy restricts target accounts. This concerns limit which storage accounts a subnet can reach over service endpoints. Here, the client bypassed the certificate's expected service hostname.
D:Storage firewall VNet rule or service endpoint configuration is missing. This concerns a higher-trust path to azure storage while retaining the service's public endpoint. Here, the client bypassed the certificate's expected service hostname.
Question 757
A new private endpoint points at the wrong Azure Storage account. Which Azure networking design most directly satisfies this requirement?
- Use supported Private Link Service visibility and approval controls
- Add the subnet to the target storage firewall's allowed networks
- Correct the private endpoint target resource before using it
- Apply an Azure Storage service endpoint policy to the subnet
Explanation
Correct Answer
C:Correct the private endpoint target resource before using it addresses the topology, access or delivery requirement in the scenario. Apply it by recreate or correctly configure the endpoint with target resource ID and subresource; confirm by check endpoint connection target and perform an authorized operation.
Incorrect Answers
A:Use supported Private Link Service visibility and approval controls. This concerns identifying different consumer connections. Here, correct the private endpoint target resource before using it.
B:Add the subnet to the target storage firewall's allowed networks. This is relevant when a subnet's service endpoint setting exists but storage traffic is still rejected. Here, correct the private endpoint target resource before using it.
D:Apply an Azure Storage service endpoint policy to the subnet. This concerns limit which storage accounts a subnet can reach over service endpoints. Here, correct the private endpoint target resource before using it.
Question 758
A new private endpoint points at the wrong Azure Storage account. The architecture uses this design: Correct the private endpoint target resource before using it. Which configuration should the engineer apply to implement it?
- Add the vault private endpoint and appropriate private DNS zone group
- Enable service endpoint and add the specific subnet to allowed network rules
- Create a Private Link Service bound to a supported Standard Load Balancer frontend
- Recreate or correctly configure the endpoint with target resource ID and subresource
Explanation
Correct Answer
D:Recreate or correctly configure the endpoint with target resource ID and subresource is the operational configuration for correct the private endpoint target resource before using it. The acceptance test is to check endpoint connection target and perform an authorized operation.
Incorrect Answers
A:Add the vault private endpoint and appropriate private DNS zone group is a concrete step for create an azure key vault private endpoint and restrict public network access. Here the selected design is correct the private endpoint target resource before using it, which instead requires recreate or correctly configure the endpoint with target resource id and subresource.
B:Enable service endpoint and add the specific subnet to allowed network rules is a concrete step for use service endpoint-based virtual network access rules on the storage account. Here the selected design is correct the private endpoint target resource before using it, which instead requires recreate or correctly configure the endpoint with target resource id and subresource.
C:Create a Private Link Service bound to a supported Standard Load Balancer frontend is a concrete step for publish the service through azure private link service. Here the selected design is correct the private endpoint target resource before using it, which instead requires recreate or correctly configure the endpoint with target resource id and subresource.
Question 759
A new private endpoint points at the wrong Azure Storage account. After the team applies this change—recreate or correctly configure the endpoint with target resource ID and subresource—which validation best proves the intended result?
- Resolve the service FQDN privately from the branch and establish a connection
- Resolve the SQL server hostname to the endpoint IP from the application VNet
- Test connection to an allowed and forbidden storage account
- Check endpoint connection target and perform an authorized operation
Explanation
Correct Answer
D:Check endpoint connection target and perform an authorized operation directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether the endpoint references the wrong target resource ID.
Incorrect Answers
A:Resolve the service FQDN privately from the branch and establish a connection. This concerns a design compares private endpoints and service endpoints for inbound access from a branch network. Instead, check endpoint connection target and perform an authorized operation.
B:Resolve the SQL server hostname to the endpoint IP from the application VNet. This concerns being reachable privately from an application VNet. Instead, check endpoint connection target and perform an authorized operation.
C:Test connection to an allowed and forbidden storage account. This concerns limit which storage accounts a subnet can reach over service endpoints. Instead, check endpoint connection target and perform an authorized operation.
Question 760
A new private endpoint points at the wrong Azure Storage account. During acceptance testing, requests land at a different account from the one intended. Which underlying configuration problem best explains the symptom?
- Service endpoints do not provide an on-premises private IP endpoint
- The endpoint references the wrong target resource ID
- A service endpoint was chosen for a requirement that needs Private Link
- Only development's subnet has the service endpoint policy attached
Explanation
Correct Answer
B:The endpoint references the wrong target resource ID explains the observed failure: requests land at a different account from the one intended. Correct the design by using correct the private endpoint target resource before using it, implemented through recreate or correctly configure the endpoint with target resource ID and subresource.
Incorrect Answers
A:Service endpoints do not provide an on-premises private IP endpoint. This concerns a design compares private endpoints and service endpoints for inbound access from a branch network. Here, the endpoint references the wrong target resource ID.
C:A service endpoint was chosen for a requirement that needs Private Link. This concerns all paas connections to remain on exclusively private addresses. Here, the endpoint references the wrong target resource ID.
D:Only development's subnet has the service endpoint policy attached. This concerns a service endpoint policy works in development but not in the production subnet. Here, the endpoint references the wrong target resource ID.
Designing and Implementing Microsoft Azure Networking Solutions (AZ-700) Practice Tests