100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 1060
A Junos enterprise team investigates this incident: A host moves between leafs and the destination leaf still forwards toward the previous MAC location. Which technical explanation most directly identifies the cause or design principle?
- VXLAN encapsulates overlay traffic across an IP underlay; VTEP reachability is necessary even with valid BGP EVPN control-plane state.
- VXLAN adds encapsulation overhead, so underlay MTU must accommodate the intended overlay frame size.
- EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane.
- VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic.
Explanation
Correct Answer
C:EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane. The appropriate response is to check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.
Incorrect Answers
A:“VXLAN encapsulates overlay traffic across an IP underlay; VTEP reachability is necessary even with valid BGP EVPN control-plane state” belongs to a separate EVPN issue: a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback. It does not explain the condition tested here.
B:“VXLAN adds encapsulation overhead, so underlay MTU must accommodate the intended overlay frame size” belongs to a separate EVPN issue: an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. It does not explain the condition tested here.
D:“VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic” belongs to a separate EVPN issue: a campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. It does not explain the condition tested here.
Question 1061
A network change is required for the following specific situation: A corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. Which corrective action is most appropriate?
- Configure supported MAC RADIUS under least-privilege policy and register the device MAC with the approved service.
- Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.
- Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
- Assign the authenticated device to the authorized restricted network profile and verify effective VLAN/filter.
Explanation
Correct Answer
C:802.1X authorization depends on the authenticator, supplicant and authentication-server conversation being correctly connected. Verify this by checking that a known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state.
Incorrect Answers
A:“Configure supported MAC RADIUS under least-privilege policy and register the device MAC with the approved service” belongs to a separate Layer 2 Authentication and Access Control issue: an industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service. It does not explain the condition tested here.
B:“Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. It does not explain the condition tested here.
D:“Assign the authenticated device to the authorized restricted network profile and verify effective VLAN/filter” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS policy authenticates a known camera but applies the broad employee VLAN instead of a camera-only network. It does not explain the condition tested here.
Question 1062
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile.
- Give MAC-authenticated devices the same unrestricted access as strongly authenticated employees.
- Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
- A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state.
- Grant unbounded port access to all endpoints instead of diagnosing the RADIUS/EAP path.
- Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event.
Explanation
Correct Answers
B:Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration. This addresses the dependency that 802.1X authorization depends on the authenticator, supplicant and authentication-server conversation being correctly connected.
C:A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state. The specific steps required are to inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
Incorrect Answers
A:“Give MAC-authenticated devices the same unrestricted access as strongly authenticated employees” is an unsafe response to a different problem: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It is not a valid fix here.
D:“Grant unbounded port access to all endpoints instead of diagnosing the RADIUS/EAP path” does not address 802.1X authorization depends on the authenticator, supplicant and authentication-server conversation being correctly connected.
E:“Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event” is an unsafe response to a different problem: a credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants. It is not a valid fix here.
Question 1063
Select THREE complementary corrective, verification, or preventive controls for this scenario: A noninteractive sensor is trapped in captive-portal onboarding because operators selected browser authentication for all endpoints.
- Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event.
- Classify interactive and headless endpoint requirements before choosing the access method.
- Require the scanner to open a login web page even though the device has no web client.
- Choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.
- Assume any RADIUS Access-Accept forces a requested dynamic VLAN on every Junos switch variant.
- The scanner authenticates through the approved method without any browser step, while unknown devices stay denied.
Explanation
Correct Answers
B:Prevention of recurrence: Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices.
D:Correction: Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices.
F:Confirmation: Choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.
Incorrect Answers
A:“Treat rejected credentials and no-supplicant detection as the same unconditional guest-access event” is an unsafe response to a different problem: a switch assigns a misconfigured laptop with incorrect EAP credentials to a VLAN intended only for devices that never attempt 802.1X. It is not a valid fix here.
C:“Require the scanner to open a login web page even though the device has no web client” does not address captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices.
E:“Assume any RADIUS Access-Accept forces a requested dynamic VLAN on every Junos switch variant” is an unsafe response to a different problem: an EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization. It is not a valid fix here.
Question 1064
The team believes it has resolved this Junos issue: A policy-based VLAN filter moves matching device traffic to a quarantine VLAN but a rule fails to match the intended MAC or packet fields. Which observation best verifies the specific intended result?
- A packet capture shows the contracted customer tag or untagged frame at the endpoint.
- Both switches show compatible region membership and intended instance root/port roles.
- The VLAN registration propagates to the intended downstream trunk and reaches its member ports.
- Matching test traffic enters the quarantine VLAN while ordinary traffic stays in the expected VLAN.
Explanation
Correct Answer
D:Matching test traffic enters the quarantine VLAN while ordinary traffic stays in the expected VLAN. This checks the relevant result after inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.
Incorrect Answers
A:“A packet capture shows the contracted customer tag or untagged frame at the endpoint” belongs to a separate Ethernet Switching and Spanning Tree issue: a Q-in-Q service works across transport but the far-end access handoff presents unexpected double tags. It does not explain the condition tested here.
B:“Both switches show compatible region membership and intended instance root/port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: two adjacent MSTP switches show different region digests after one has a different VLAN-to-instance map. It does not explain the condition tested here.
C:“The VLAN registration propagates to the intended downstream trunk and reaches its member ports” belongs to a separate Ethernet Switching and Spanning Tree issue: a new switch automatically discovers VLAN registrations on one trunk, but an intermediate trunk lacks MVRP participation and blocks the VLAN. It does not explain the condition tested here.
Question 1065
To prevent recurrence of this precise networking failure, which practice should be adopted? A PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface.
- Check multicast and unicast topology alignment whenever routing paths or metrics change.
- Include routed-interface PIM enrollment in the multicast deployment checklist.
- Measure receiver interest and multicast forwarding state before scaling new one-to-many services.
- Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
Explanation
Correct Answer
B:Include routed-interface PIM enrollment in the multicast deployment checklist. This guards against PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.
Incorrect Answers
A:“Check multicast and unicast topology alignment whenever routing paths or metrics change” belongs to a separate IP Multicast issue: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It does not explain the condition tested here.
C:“Measure receiver interest and multicast forwarding state before scaling new one-to-many services” belongs to a separate IP Multicast issue: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It does not explain the condition tested here.
D:“Document ASM/SSM selection and receiver-version prerequisites before multicast deployment” belongs to a separate IP Multicast issue: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It does not explain the condition tested here.
Question 1066
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint.
- The redundant topology converges without sustained broadcast loops during link-failure testing.
- Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated.
- Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
- Make every switch-to-switch uplink an edge port to accelerate convergence.
- Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN.
Explanation
Correct Answers
A:The redundant topology converges without sustained broadcast loops during link-failure testing. The specific steps required are to remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
C:Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles. This addresses the dependency that spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections.
Incorrect Answers
B:“Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated” is an unsafe response to a different problem: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It is not a valid fix here.
D:“Make every switch-to-switch uplink an edge port to accelerate convergence” does not address spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections.
E:“Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN” is an unsafe response to a different problem: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It is not a valid fix here.
Question 1067
A Junos enterprise team investigates this incident: A RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. Which technical explanation most directly identifies the cause or design principle?
- Supplicant absence is a distinct failure from an invalid credential or unreachable authentication server.
- MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication.
- Captive portal requires a supported browser interception and authentication-to-authorization sequence.
- MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision.
Explanation
Correct Answer
A:Supplicant absence is a distinct failure from an invalid credential or unreachable authentication server. The appropriate response is to inspect packet exchange and classify the endpoint before selecting a supported fallback method.
Incorrect Answers
B:“MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication” belongs to a separate Layer 2 Authentication and Access Control issue: a printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy. It does not explain the condition tested here.
C:“Captive portal requires a supported browser interception and authentication-to-authorization sequence” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.
D:“MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS policy authenticates a known camera but applies the broad employee VLAN instead of a camera-only network. It does not explain the condition tested here.
Question 1068
The team believes it has resolved this Junos issue: A carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path. Which observation best verifies the specific intended result?
- A loopback-to-loopback BGP session becomes Established and exchanges only permitted NLRI.
- After policy correction, chosen path and attribute ordering match documented routing intent.
- The route is accepted only after the AS-path loop is removed, with stable forwarding.
- The expected IPv6 prefix is received in inet6.0 while IPv4 route exchange remains unchanged.
Explanation
Correct Answer
C:The route is accepted only after the AS-path loop is removed, with stable forwarding. This checks the relevant result after check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks.
Incorrect Answers
A:“A loopback-to-loopback BGP session becomes Established and exchanges only permitted NLRI” belongs to a separate Border Gateway Protocol (BGP) issue: a transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated. It does not explain the condition tested here.
B:“After policy correction, chosen path and attribute ordering match documented routing intent” belongs to a separate Border Gateway Protocol (BGP) issue: a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops. It does not explain the condition tested here.
D:“The expected IPv6 prefix is received in inet6.0 while IPv4 route exchange remains unchanged” belongs to a separate Border Gateway Protocol (BGP) issue: BGP peers exchange IPv4 NLRI correctly but a planned IPv6 customer route never appears in inet6.0. It does not explain the condition tested here.
Question 1069
Which suggested shortcut would be especially unsafe for this exact situation? An access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed.
- Validate classifier, scheduler map and interface association as a complete CoS chain.
- Assume more queues automatically improve latency even if control traffic remains mapped to a congested queue.
- Keep queue drop-profile acceptance tests and monitor production congestion before broad rollout.
- Audit DSCP preservation and remarking at untrusted edge boundaries.
Explanation
Correct Answer
B:The tempting alternative fails because forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays. The supported action is to review the forwarding class and queue map for control and data traffic and apply the intended assignments.
Incorrect Answers
A:That prevention measure relates to a campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a RED drop profile is applied too aggressively and drops packets even under moderate load.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic.; it is not the unsafe shortcut described here.
Question 1070
A network change is required for the following specific situation: A redundant network changes the preferred route to the source while packets keep arriving on the other physical link. Which corrective action is most appropriate?
- Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.
- Compare source-route preference with actual multicast ingress and restore a consistent authorized upstream path.
- Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
- Verify anycast RP address and supported source synchronization method across the participating RP nodes.
Explanation
Correct Answer
B:An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic. Verify this by checking that RPF counters and expected (S,G) forwarding stabilize after the route change.
Incorrect Answers
A:“Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.
C:“Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding” belongs to a separate IP Multicast issue: a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. It does not explain the condition tested here.
D:“Verify anycast RP address and supported source synchronization method across the participating RP nodes” belongs to a separate IP Multicast issue: an Anycast RP design uses two RP addresses that do not share the intended anycast identity, producing inconsistent joins. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests