Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 11

Question 100

A network change is required for the following specific situation: A MAC RADIUS policy authenticates a known camera but applies the broad employee VLAN instead of a camera-only network. Which corrective action is most appropriate?

  1. Assign the authenticated device to the authorized restricted network profile and verify effective VLAN/filter.
  2. Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
  3. Inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior.
  4. Choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.

Explanation

Correct Answer

A:

MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision. Verify this by checking that the known device reaches only permitted destinations and cannot reach employee or management resources.

Incorrect Answers

B:

“Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform” belongs to a separate Layer 2 Authentication and Access Control issue: an enterprise fallback design accidentally places unauthenticated users into the production network when all RADIUS servers fail. It does not explain the condition tested here.

C:

“Inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior” belongs to a separate Layer 2 Authentication and Access Control issue: two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result. It does not explain the condition tested here.

D:

“Choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls” belongs to a separate Layer 2 Authentication and Access Control issue: a captive portal requirement is applied to a headless barcode scanner that has no web browser to follow its redirect. It does not explain the condition tested here.

Question 101

Which suggested shortcut would be especially unsafe for this exact situation? An aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure.

  1. Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated.
  2. Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews.
  3. Audit edge classifications and apply appropriate BPDU protection on true client-facing ports.
  4. Keep explicit root priority policy and validate elections after device replacement.

Explanation

Correct Answer

A:

The tempting alternative fails because Q-in-Q encapsulation can place a provider outer tag around customer VLAN tags to isolate transport context. The supported action is to design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.

Incorrect Answers

B:

That prevention measure relates to a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a campus mistakenly enables edge behavior on a switch-to-switch trunk and a loop appears when a backup link activates.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet.; it is not the unsafe shortcut described here.

Question 102

A network change is required for the following specific situation: A fabric uses conflicting VLAN-to-VNI mappings on two leaf switches, bridging different tenant segments together. Which corrective action is most appropriate?

  1. Inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally.
  2. Check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.
  3. Compare VLAN-to-VNI and bridge-domain assignments on all leafs and correct them against the approved tenant map.
  4. Align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes.

Explanation

Correct Answer

C:

VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic. Verify this by checking that tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated.

Incorrect Answers

A:

“Inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally” belongs to a separate EVPN issue: a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. It does not explain the condition tested here.

B:

“Check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain” belongs to a separate EVPN issue: a host moves between leafs and the destination leaf still forwards toward the previous MAC location. It does not explain the condition tested here.

D:

“Align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes” belongs to a separate EVPN issue: a multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. It does not explain the condition tested here.

Question 103

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: Two queues use the same scheduler priority, but the business expects one to always win during contention.

  1. Assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.
  2. Map every packet to the lowest loss priority regardless of its out-of-profile status.
  3. Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses.
  4. Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing.
  5. Trust arbitrary user DSCP markings as proof every packet belongs in the high-priority class.

Explanation

Correct Answers

A:

Assign the intended service class and scheduler priorities with measured bandwidth needs, then validate. This addresses the dependency that scheduler priority and bandwidth allocation affect queuing service but must balance fairness and starvation concerns.

C:

Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses. The specific steps required are to assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.

Incorrect Answers

B:

“Map every packet to the lowest loss priority regardless of its out-of-profile status” is an unsafe response to a different problem: packets with two different drop precedence values are treated as equally discardable during congestion. It is not a valid fix here.

D:

“Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing” does not address scheduler priority and bandwidth allocation affect queuing service but must balance fairness and starvation concerns.

E:

“Trust arbitrary user DSCP markings as proof every packet belongs in the high-priority class” is an unsafe response to a different problem: an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It is not a valid fix here.

Question 104

Select THREE complementary corrective, verification, or preventive controls for this scenario: A multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop.

  1. Assume IGMP membership on the access switch alone builds an end-to-end PIM ASM tree.
  2. Configure two unrelated RP mappings and assume their failover and source state stay identical automatically.
  3. Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.
  4. Assume inet.0 always controls PIM RPF even when an alternate multicast RPF table is configured.
  5. Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
  6. The selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow.

Explanation

Correct Answers

C:

Prevention of recurrence: Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.

E:

Correction: Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.

F:

Confirmation: Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.

Incorrect Answers

A:

“Assume IGMP membership on the access switch alone builds an end-to-end PIM ASM tree” is an unsafe response to a different problem: a PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point. It is not a valid fix here.

B:

“Configure two unrelated RP mappings and assume their failover and source state stay identical automatically” is an unsafe response to a different problem: a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it. It is not a valid fix here.

D:

“Assume inet.0 always controls PIM RPF even when an alternate multicast RPF table is configured” does not address Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.

Question 105

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A bridge domain has valid unicast Type 2 entries yet remote VTEPs do not discover a new participating segment for BUM forwarding.

  1. BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered.
  2. Inspect Type 3 routes and VNI import/export membership; repair the intended inclusive-multicast advertisement.
  3. Treat a single learned MAC/IP Type 2 route as guaranteed proof of correct BUM participation for every VTEP.
  4. Assume an Ethernet payload that fits a non-VXLAN path always fits once the VXLAN overhead is added.
  5. Use two unrelated ESIs for one logical Ethernet segment and assume EVPN coordinates them as one.

Explanation

Correct Answers

A:

BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered. The specific steps required are to inspect Type 3 routes and VNI import/export membership; repair the intended inclusive-multicast advertisement.

B:

Inspect Type 3 routes and VNI import/export membership; repair the intended inclusive-multicast advertisement. This addresses the dependency that EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set.

Incorrect Answers

C:

“Treat a single learned MAC/IP Type 2 route as guaranteed proof of correct BUM participation for every VTEP” does not address EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set.

D:

“Assume an Ethernet payload that fits a non-VXLAN path always fits once the VXLAN overhead is added” is an unsafe response to a different problem: an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. It is not a valid fix here.

E:

“Use two unrelated ESIs for one logical Ethernet segment and assume EVPN coordinates them as one” is an unsafe response to a different problem: a shared Ethernet segment loses its fast convergence properties after an ESI-LAG peer receives an inconsistent configuration. It is not a valid fix here.

Question 106

To prevent recurrence of this precise networking failure, which practice should be adopted? A network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN.

  1. Track MSTP instance scale and maintain identical region parameters across participating switches.
  2. Include MVRP adjacency and registration checks in trunk-change reviews.
  3. Check policy coverage and unintended-match cases before activating filter-based steering.
  4. Test private-port isolation and uplink reachability after access topology changes.

Explanation

Correct Answer

A:

Track MSTP instance scale and maintain identical region parameters across participating switches. This guards against MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.

Incorrect Answers

B:

“Include MVRP adjacency and registration checks in trunk-change reviews” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. It does not explain the condition tested here.

C:

“Check policy coverage and unintended-match cases before activating filter-based steering” belongs to a separate Ethernet Switching and Spanning Tree issue: an ingress classification filter for one terminal type inadvertently redirects other hosts using the same uplink. It does not explain the condition tested here.

D:

“Test private-port isolation and uplink reachability after access topology changes” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It does not explain the condition tested here.

Question 107

The team believes it has resolved this Junos issue: A switch logs EAP timeout while the endpoint has no 802.1X supplicant, yet the operator rotates valid RADIUS passwords repeatedly. Which observation best verifies the specific intended result?

  1. The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint.
  2. Authenticated corporate devices use strong EAP policies while designated legacy endpoints use restricted fallback.
  3. The user sees a valid login prompt and receives only the approved post-login policy.
  4. The registered device is authorized with limited access; an unknown MAC remains blocked.

Explanation

Correct Answer

A:

The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint. This checks the relevant result after inspect packet exchange and classify the endpoint before selecting a supported fallback method.

Incorrect Answers

B:

“Authenticated corporate devices use strong EAP policies while designated legacy endpoints use restricted fallback” belongs to a separate Layer 2 Authentication and Access Control issue: two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result. It does not explain the condition tested here.

C:

“The user sees a valid login prompt and receives only the approved post-login policy” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.

D:

“The registered device is authorized with limited access; an unknown MAC remains blocked” belongs to a separate Layer 2 Authentication and Access Control issue: a non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. It does not explain the condition tested here.

Question 108

A network change is required for the following specific situation: An EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. Which corrective action is most appropriate?

  1. Inspect Type 3 routes and VNI import/export membership; repair the intended inclusive-multicast advertisement.
  2. Inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally.
  3. Inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.
  4. Check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.

Explanation

Correct Answer

C:

EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops. Verify this by checking that BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates.

Incorrect Answers

A:

“Inspect Type 3 routes and VNI import/export membership; repair the intended inclusive-multicast advertisement” belongs to a separate EVPN issue: a VNI is active on two leafs but unknown-unicast or broadcast replication never reaches the remote side. It does not explain the condition tested here.

B:

“Inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally” belongs to a separate EVPN issue: a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. It does not explain the condition tested here.

D:

“Check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain” belongs to a separate EVPN issue: a host moves between leafs and the destination leaf still forwards toward the previous MAC location. It does not explain the condition tested here.

Question 109

A Junos enterprise team investigates this incident: An EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization. Which technical explanation most directly identifies the cause or design principle?

  1. Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary.
  2. Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.
  3. Captive portal requires a supported browser interception and authentication-to-authorization sequence.
  4. MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision.

Explanation

Correct Answer

A:

Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary. The appropriate response is to check returned RADIUS attributes and supported platform software, then enforce a valid authorization assignment.

Incorrect Answers

B:

“Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies” belongs to a separate Layer 2 Authentication and Access Control issue: a switch assigns a misconfigured laptop with incorrect EAP credentials to a VLAN intended only for devices that never attempt 802.1X. It does not explain the condition tested here.

C:

“Captive portal requires a supported browser interception and authentication-to-authorization sequence” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.

D:

“MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision” belongs to a separate Layer 2 Authentication and Access Control issue: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It does not explain the condition tested here.

Question 110

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A filter-based VLAN security design uses a rule that catches too many packets and steers legitimate devices into quarantine.

  1. Narrow the match to approved selectors and compare affected packet counters and VLAN assignment.
  2. Use a catch-all quarantine match without analyzing which hosts also traverse the interface.
  3. Make every switch-to-switch uplink an edge port to accelerate convergence.
  4. Only the intended endpoint class is moved while nonmatching hosts retain correct access.
  5. Create an independent VSTP instance for every VLAN without checking platform scaling limits.

Explanation

Correct Answers

A:

Narrow the match to approved selectors and compare affected packet counters and VLAN assignment. This addresses the dependency that overbroad match conditions can cause unauthorized VLAN steering and affect both security and reachability.

D:

Only the intended endpoint class is moved while nonmatching hosts retain correct access. The specific steps required are to narrow the match to approved selectors and compare affected packet counters and VLAN assignment.

Incorrect Answers

B:

“Use a catch-all quarantine match without analyzing which hosts also traverse the interface” does not address overbroad match conditions can cause unauthorized VLAN steering and affect both security and reachability.

C:

“Make every switch-to-switch uplink an edge port to accelerate convergence” is an unsafe response to a different problem: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It is not a valid fix here.

E:

“Create an independent VSTP instance for every VLAN without checking platform scaling limits” is an unsafe response to a different problem: a large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits. It is not a valid fix here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.