Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 9

Question 80

To prevent recurrence of this precise networking failure, which practice should be adopted? A route-reflector client receives an external destination but lacks the underlay path to the advertised next hop.

  1. Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
  2. Test expected best-path behavior before modifying LOCAL_PREF across internal peers.
  3. Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP.
  4. Include show route hidden and policy term hit checks in BGP troubleshooting playbooks.

Explanation

Correct Answer

C:

Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP. This guards against a reachable BGP peering session does not itself make a third-party route next hop recursively resolvable.

Incorrect Answers

A:

“Audit prefix and mask-length boundaries with positive and negative routing-policy tests” belongs to a separate Border Gateway Protocol (BGP) issue: a prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor. It does not explain the condition tested here.

B:

“Test expected best-path behavior before modifying LOCAL_PREF across internal peers” belongs to a separate Border Gateway Protocol (BGP) issue: an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path. It does not explain the condition tested here.

D:

“Include show route hidden and policy term hit checks in BGP troubleshooting playbooks” belongs to a separate Border Gateway Protocol (BGP) issue: a Junos route is hidden by import policy, but the team troubleshoots only local physical interfaces. It does not explain the condition tested here.

Question 81

A Junos enterprise team investigates this incident: An access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. Which technical explanation most directly identifies the cause or design principle?

  1. Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface.
  2. Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays.
  3. Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract.
  4. CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings.

Explanation

Correct Answer

B:

Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays. The appropriate response is to review the forwarding class and queue map for control and data traffic and apply the intended assignments.

Incorrect Answers

A:

“Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface” belongs to a separate Class of Service (CoS) issue: a low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk. It does not explain the condition tested here.

C:

“Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract” belongs to a separate Class of Service (CoS) issue: a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. It does not explain the condition tested here.

D:

“CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings” belongs to a separate Class of Service (CoS) issue: a customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic. It does not explain the condition tested here.

Question 82

A network change is required for the following specific situation: A redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local. Which corrective action is most appropriate?

  1. Compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints.
  2. Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.
  3. Compare configured interface areas with the approved topology and put both interfaces in the intended matching area.
  4. Assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence.

Explanation

Correct Answer

B:

Unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability. Verify this by checking that only authorized static prefixes appear as OSPF externals; management prefixes remain local.

Incorrect Answers

A:

“Compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints” belongs to a separate Interior Gateway Protocols (IGPs) issue: two EX distribution routers in OSPF area 0 remain in ExStart after a new transit VLAN uses inconsistent interface MTUs. It does not explain the condition tested here.

C:

“Compare configured interface areas with the approved topology and put both interfaces in the intended matching area” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch uplink uses area 0.0.0.6 on one router and area 0.0.0.9 on its peer after a template copy. It does not explain the condition tested here.

D:

“Assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence” belongs to a separate Interior Gateway Protocols (IGPs) issue: two newly deployed distribution switches report identical OSPF router IDs, causing inconsistent LSAs in the area. It does not explain the condition tested here.

Question 83

A network change is required for the following specific situation: A new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. Which corrective action is most appropriate?

  1. Select a permitted inbound traffic-engineering mechanism with the provider, such as suitable AS-path prepending or agreed communities.
  2. Enable the intended inet6 family consistently on eligible BGP peers and verify route policy and inet6.0.
  3. Document and test terminal accept or reject behavior along with next-term and next-policy handling.
  4. Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.

Explanation

Correct Answer

D:

BGP route selection first requires the BGP next hop to resolve through the appropriate routing table. Verify this by checking that the previously hidden BGP prefix resolves its next hop and becomes an eligible route.

Incorrect Answers

A:

“Select a permitted inbound traffic-engineering mechanism with the provider, such as suitable AS-path prepending or agreed communities” belongs to a separate Border Gateway Protocol (BGP) issue: an operator tries to make a remote AS prefer one inbound path using LOCAL_PREF that the remote eBGP peer never receives. It does not explain the condition tested here.

B:

“Enable the intended inet6 family consistently on eligible BGP peers and verify route policy and inet6.0” belongs to a separate Border Gateway Protocol (BGP) issue: a campus router's BGP IPv6 session is Established yet peers advertise only inet unicast family routes. It does not explain the condition tested here.

C:

“Document and test terminal accept or reject behavior along with next-term and next-policy handling” belongs to a separate Border Gateway Protocol (BGP) issue: a route policy lacks an explicit intended default action, and unmatched BGP prefixes behave differently than planned. It does not explain the condition tested here.

Question 84

Which suggested shortcut would be especially unsafe for this exact situation? A noninteractive sensor is trapped in captive-portal onboarding because operators selected browser authentication for all endpoints.

  1. Review authorization policies for MAC endpoints against a least-privilege access matrix.
  2. Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions.
  3. Document and test EAP timeout, explicit rejection and server-unavailable cases separately.
  4. Require the scanner to open a login web page even though the device has no web client.

Explanation

Correct Answer

D:

The tempting alternative fails because captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices. The supported action is to choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.

Incorrect Answers

A:

That prevention measure relates to a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a switch assigns a misconfigured laptop with incorrect EAP credentials to a VLAN intended only for devices that never attempt 802.1X.; it is not the unsafe shortcut described here.

Question 85

Select THREE complementary corrective, verification, or preventive controls for this scenario: An uplink meets long-term bandwidth policy but legitimate short bursts exceed the token-bucket allowance.

  1. Controlled traffic probes pass valid bursts without permitting sustained rate violations.
  2. Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration.
  3. Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy.
  4. Test both average-rate enforcement and microburst tolerance for new policer profiles.
  5. Create a scheduler definition in configuration but never bind the scheduler map to egress interfaces.
  6. Measure burst patterns and adjust the policer burst configuration within the authorized service contract.

Explanation

Correct Answers

A:

Confirmation: Measure burst patterns and adjust the policer burst configuration within the authorized service contract.

D:

Prevention of recurrence: Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.

F:

Correction: Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.

Incorrect Answers

B:

“Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration” does not address policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.

C:

“Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy” is an unsafe response to a different problem: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It is not a valid fix here.

E:

“Create a scheduler definition in configuration but never bind the scheduler map to egress interfaces” is an unsafe response to a different problem: a campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing. It is not a valid fix here.

Question 86

A network change is required for the following specific situation: A forwarding-class configuration sends critical routing packets to a queue used for bulk backups and adjacency stability degrades under load. Which corrective action is most appropriate?

  1. Associate the approved scheduler map with the correct egress interface and confirm class queue counters.
  2. Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment.
  3. Review the forwarding class and queue map for control and data traffic and apply the intended assignments.
  4. Apply the appropriate interface rewrite rule and verify the contract-specific egress code points.

Explanation

Correct Answer

C:

Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays. Verify this by checking that control-plane-related traffic receives the expected queue treatment under simulated load.

Incorrect Answers

A:

“Associate the approved scheduler map with the correct egress interface and confirm class queue counters” belongs to a separate Class of Service (CoS) issue: a low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk. It does not explain the condition tested here.

B:

“Review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment” belongs to a separate Class of Service (CoS) issue: video gets dropped under congestion despite spare capacity because its queue has a too-small delay buffer. It does not explain the condition tested here.

D:

“Apply the appropriate interface rewrite rule and verify the contract-specific egress code points” belongs to a separate Class of Service (CoS) issue: a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. It does not explain the condition tested here.

Question 87

Select THREE complementary corrective, verification, or preventive controls for this scenario: A video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application.

  1. Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.
  2. Assume an ASM (*,G) join identifies and restricts a unique approved source by itself.
  3. Assume IGMP membership on the access switch alone builds an end-to-end PIM ASM tree.
  4. Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
  5. Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages.
  6. Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow.

Explanation

Correct Answers

A:

Correction: Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow.

D:

Prevention of recurrence: Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow.

F:

Confirmation: Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.

Incorrect Answers

B:

“Assume an ASM (*,G) join identifies and restricts a unique approved source by itself” does not address source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow.

C:

“Assume IGMP membership on the access switch alone builds an end-to-end PIM ASM tree” is an unsafe response to a different problem: an ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP. It is not a valid fix here.

E:

“Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages” is an unsafe response to a different problem: a multicast source is active in a different PIM domain but the local ASM RP never learns the source mapping. It is not a valid fix here.

Question 88

Which suggested shortcut would be especially unsafe for this exact situation? A phone-with-PC desk deployment lets the PC reach data services while the tagged voice stream is dropped by VLAN membership.

  1. Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
  2. Put the phone and PC on one unrestricted VLAN to avoid checking voice VLAN tagging.
  3. Review LLDP-MED state and phone compliance during access-switch template audits.
  4. Include LLDP-MED capabilities and network-policy TLVs in phone-vendor acceptance testing.

Explanation

Correct Answer

B:

The tempting alternative fails because voice/data split depends on compatible VLAN membership, accepted 802.1Q tagging and endpoint network policy. The supported action is to configure an approved voice VLAN on the port while keeping the PC data VLAN constrained.

Incorrect Answers

A:

That prevention measure relates to a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a vendor handset discovers its neighbor using basic LLDP but does not learn the configured network policy for voice tagging.; it is not the unsafe shortcut described here.

Question 89

A network change is required for the following specific situation: A powered endpoint detects a Junos switch but fails to negotiate voice prioritization because only ordinary LLDP is enabled. Which corrective action is most appropriate?

  1. Inspect PoE class, per-port priority and available chassis budget, and move to a supported powered port if needed.
  2. Configure an approved voice VLAN on the port while keeping the PC data VLAN constrained.
  3. Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
  4. Review LLDP and LLDP-MED operational status and enable supported MED policy for phone access.

Explanation

Correct Answer

D:

Base LLDP discovery and LLDP-MED telephony advertisement are distinct capabilities and may require separate enablement. Verify this by checking that packet and operational views show the required LLDP-MED telephony TLVs at the correct interface.

Incorrect Answers

A:

“Inspect PoE class, per-port priority and available chassis budget, and move to a supported powered port if needed” belongs to a separate IP Telephony Features issue: a phone's LLDP-negotiated power demand exceeds its access port's allocated PoE limit and it repeatedly restarts. It does not explain the condition tested here.

B:

“Configure an approved voice VLAN on the port while keeping the PC data VLAN constrained” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.

C:

“Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media” belongs to a separate IP Telephony Features issue: a voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. It does not explain the condition tested here.

Question 90

The team believes it has resolved this Junos issue: A redundant network changes the preferred route to the source while packets keep arriving on the other physical link. Which observation best verifies the specific intended result?

  1. RPF counters and expected (S,G) forwarding stabilize after the route change.
  2. Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream.
  3. Only the specified source delivers data to receivers of the chosen SSM group.
  4. The required PIM neighbors appear and downstream join state tracks active interested receivers.

Explanation

Correct Answer

A:

RPF counters and expected (S,G) forwarding stabilize after the route change. This checks the relevant result after compare source-route preference with actual multicast ingress and restore a consistent authorized upstream path.

Incorrect Answers

B:

“Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream” belongs to a separate IP Multicast issue: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It does not explain the condition tested here.

C:

“Only the specified source delivers data to receivers of the chosen SSM group” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.

D:

“The required PIM neighbors appear and downstream join state tracks active interested receivers” belongs to a separate IP Multicast issue: a PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.