100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 1100
Select THREE complementary corrective, verification, or preventive controls for this scenario: A voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget.
- Check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power.
- The phone receives stable negotiated power and the chassis stays within its supported budget under peak load.
- Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN.
- Put the phone and PC on one unrestricted VLAN to avoid checking voice VLAN tagging.
- Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
- Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power.
Explanation
Correct Answers
A:Correction: PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status.
B:Confirmation: Check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power.
E:Prevention of recurrence: PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status.
Incorrect Answers
C:“Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN” is an unsafe response to a different problem: a handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design. It is not a valid fix here.
D:“Put the phone and PC on one unrestricted VLAN to avoid checking voice VLAN tagging” is an unsafe response to a different problem: a phone-with-PC desk deployment lets the PC reach data services while the tagged voice stream is dropped by VLAN membership. It is not a valid fix here.
F:“Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power” does not address PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status.
Question 1101
A Junos enterprise team investigates this incident: A campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them. Which technical explanation most directly identifies the cause or design principle?
- MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.
- Q-in-Q requires deliberate tagging and untagging at service boundaries, with customer tags retained according to the handoff contract.
- Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
- Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point.
Explanation
Correct Answer
D:Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point. The appropriate response is to inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.
Incorrect Answers
A:“MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.
B:“Q-in-Q requires deliberate tagging and untagging at service boundaries, with customer tags retained according to the handoff contract” belongs to a separate Ethernet Switching and Spanning Tree issue: customer traffic emerges with the provider service tag still attached and is rejected by an endpoint expecting ordinary Ethernet. It does not explain the condition tested here.
C:“Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet. It does not explain the condition tested here.
Question 1102
A Junos enterprise team investigates this incident: A campus uplink transmits marked video as ordinary data because no behavior-aggregate classifier is attached at ingress. Which technical explanation most directly identifies the cause or design principle?
- Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment.
- Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract.
- Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface.
- Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings.
Explanation
Correct Answer
A:Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment. The appropriate response is to apply an approved behavior-aggregate classifier with the intended DSCP-to-class mapping on the real ingress interface.
Incorrect Answers
B:“Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract” belongs to a separate Class of Service (CoS) issue: a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. It does not explain the condition tested here.
C:“Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface” belongs to a separate Class of Service (CoS) issue: a campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing. It does not explain the condition tested here.
D:“Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings” belongs to a separate Class of Service (CoS) issue: a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. It does not explain the condition tested here.
Question 1103
To prevent recurrence of this precise networking failure, which practice should be adopted? A switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet.
- Keep explicit root priority policy and validate elections after device replacement.
- Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries.
- Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
- Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned.
Explanation
Correct Answer
A:Keep explicit root priority policy and validate elections after device replacement. This guards against spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
Incorrect Answers
B:“Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries” belongs to a separate Ethernet Switching and Spanning Tree issue: a service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff. It does not explain the condition tested here.
C:“Scope and monitor tunneled L2 control protocols to prevent control-plane abuse” belongs to a separate Ethernet Switching and Spanning Tree issue: an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently. It does not explain the condition tested here.
D:“Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned” belongs to a separate Ethernet Switching and Spanning Tree issue: a dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream. It does not explain the condition tested here.
Question 1104
The team believes it has resolved this Junos issue: A traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. Which observation best verifies the specific intended result?
- Only approved media streams leave with high-priority code points; backup traffic uses its designated mark.
- Controlled traffic probes pass valid bursts without permitting sustained rate violations.
- Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses.
- Observed queue counters show voice packets in the designated forwarding class after classification.
Explanation
Correct Answer
B:Controlled traffic probes pass valid bursts without permitting sustained rate violations. This checks the relevant result after measure burst patterns and adjust the policer burst configuration within the authorized service contract.
Incorrect Answers
A:“Only approved media streams leave with high-priority code points; backup traffic uses its designated mark” belongs to a separate Class of Service (CoS) issue: a customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic. It does not explain the condition tested here.
C:“Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses” belongs to a separate Class of Service (CoS) issue: two queues use the same scheduler priority, but the business expects one to always win during contention. It does not explain the condition tested here.
D:“Observed queue counters show voice packets in the designated forwarding class after classification” belongs to a separate Class of Service (CoS) issue: voice packets arrive with DSCP EF but are placed into the best-effort queue after a new access interface template is applied. It does not explain the condition tested here.
Question 1105
A network change is required for the following specific situation: A lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. Which corrective action is most appropriate?
- Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
- Inspect registration state and remove stale VLAN membership while preserving necessary registrations.
- Create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior.
- Inspect primary and secondary private VLAN roles and port membership; restore approved isolated/community mappings.
Explanation
Correct Answer
D:Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink. Verify this by checking that two isolated tenant ports cannot reach each other but can reach the permitted gateway uplink.
Incorrect Answers
A:“Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.
B:“Inspect registration state and remove stale VLAN membership while preserving necessary registrations” belongs to a separate Ethernet Switching and Spanning Tree issue: a dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream. It does not explain the condition tested here.
C:“Create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.
Question 1106
A Junos enterprise team investigates this incident: A telephony desk requires multiple authenticated identities while the switch policy allows only one active supplicant. Which technical explanation most directly identifies the cause or design principle?
- MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication.
- MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X.
- Captive portal requires a supported browser interception and authentication-to-authorization sequence.
- 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized.
Explanation
Correct Answer
D:802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized. The appropriate response is to select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies.
Incorrect Answers
A:“MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. It does not explain the condition tested here.
B:“MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X” belongs to a separate Layer 2 Authentication and Access Control issue: an industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service. It does not explain the condition tested here.
C:“Captive portal requires a supported browser interception and authentication-to-authorization sequence” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.
Question 1107
A network change is required for the following specific situation: An industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service. Which corrective action is most appropriate?
- Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
- Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
- Select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies.
- Configure supported MAC RADIUS under least-privilege policy and register the device MAC with the approved service.
Explanation
Correct Answer
D:MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X. Verify this by checking that the registered device is authorized with limited access; an unknown MAC remains blocked.
Incorrect Answers
A:“Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform” belongs to a separate Layer 2 Authentication and Access Control issue: an enterprise fallback design accidentally places unauthenticated users into the production network when all RADIUS servers fail. It does not explain the condition tested here.
B:“Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration” belongs to a separate Layer 2 Authentication and Access Control issue: a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. It does not explain the condition tested here.
C:“Select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies” instead concerns another network scenario: An access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It does not address the requirement here.
Question 1108
The team believes it has resolved this Junos issue: A team wrongly concludes OSPFv3 failed when inet6.0 shows a static route active and the OSPFv3 candidate inactive. Which observation best verifies the specific intended result?
- The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change.
- Stable Hellos and Full neighbor state persist through repeated protocol interval checks.
- The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency.
- The preferred primary route wins when healthy and the backup becomes active on a controlled failure.
Explanation
Correct Answer
C:The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency. This checks the relevant result after inspect inet6.0 route detail and route preferences before changing OSPFv3 neighbor configuration.
Incorrect Answers
A:“The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change” belongs to a separate Interior Gateway Protocols (IGPs) issue: two EX distribution routers in OSPF area 0 remain in ExStart after a new transit VLAN uses inconsistent interface MTUs. It does not explain the condition tested here.
B:“Stable Hellos and Full neighbor state persist through repeated protocol interval checks” belongs to a separate Interior Gateway Protocols (IGPs) issue: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It does not explain the condition tested here.
D:“The preferred primary route wins when healthy and the backup becomes active on a controlled failure” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.
Question 1109
Which suggested shortcut would be especially unsafe for this exact situation? An 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently.
- Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled.
- Document primary/secondary VLAN mappings and test permitted peer groups and isolation boundaries.
- Check policy coverage and unintended-match cases before activating filter-based steering.
- Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews.
Explanation
Correct Answer
A:The tempting alternative fails because layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough. The supported action is to configure supported L2PT for the required control protocols and verify provider-edge handling.
Incorrect Answers
B:That prevention measure relates to a switch rollout splits a team that should communicate within one PVLAN community, while protecting it from another community.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an ingress classification filter for one terminal type inadvertently redirects other hosts using the same uplink.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked.; it is not the unsafe shortcut described here.
Question 1110
A Junos enterprise team investigates this incident: A new L3 VLAN permits unicast connectivity but the PIM Hello adjacency remains absent on the active path. Which technical explanation most directly identifies the cause or design principle?
- PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.
- Multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy.
- ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender.
- Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow.
Explanation
Correct Answer
A:PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree. The appropriate response is to enable PIM on the approved routed VLAN interface and inspect neighbor and join state.
Incorrect Answers
B:“Multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy” belongs to a separate IP Multicast issue: a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. It does not explain the condition tested here.
C:“ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.
D:“Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests