Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 116

Question 1150

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A route policy lacks an explicit intended default action, and unmatched BGP prefixes behave differently than planned.

  1. Disable BGP AS-loop safeguards globally to accept any route repeating the local AS.
  2. Positive and negative prefix tests traverse the expected policy terms and produce approved import/export outcomes.
  3. Assume every unmatched policy term means a route is unconditionally accepted without checking protocol defaults.
  4. Document and test terminal accept or reject behavior along with next-term and next-policy handling.
  5. Increase the route's MED while leaving BGP transport reachability and hop settings incorrect.

Explanation

Correct Answers

B:

Positive and negative prefix tests traverse the expected policy terms and produce approved import/export outcomes. The specific steps required are to document and test terminal accept or reject behavior along with next-term and next-policy handling.

D:

Document and test terminal accept or reject behavior along with next-term and next-policy handling. This addresses the dependency that routing-policy evaluation depends on term matches, flow-control actions and the policy chain, including what happens on no match.

Incorrect Answers

A:

“Disable BGP AS-loop safeguards globally to accept any route repeating the local AS” is an unsafe response to a different problem: the local AS appears in a received external BGP AS_PATH and the route is rejected despite valid prefix reachability. It is not a valid fix here.

C:

“Assume every unmatched policy term means a route is unconditionally accepted without checking protocol defaults” does not address routing-policy evaluation depends on term matches, flow-control actions and the policy chain, including what happens on no match.

E:

“Increase the route's MED while leaving BGP transport reachability and hop settings incorrect” is an unsafe response to a different problem: a multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain. It is not a valid fix here.

Question 1151

To prevent recurrence of this precise networking failure, which practice should be adopted? Two iBGP exits offer equal reachable routes but the one with higher LOCAL_PREF is not the egress an operator expected.

  1. Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
  2. Test expected best-path behavior before modifying LOCAL_PREF across internal peers.
  3. Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews.
  4. Monitor AS-path anomalies and validate inter-AS topology changes before enabling export.

Explanation

Correct Answer

B:

Test expected best-path behavior before modifying LOCAL_PREF across internal peers. This guards against BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers.

Incorrect Answers

A:

“Include next-hop reachability tests in iBGP and route-reflector deployment acceptance” belongs to a separate Border Gateway Protocol (BGP) issue: a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. It does not explain the condition tested here.

C:

“Distinguish internal exit selection from inbound inter-AS path influence in routing design reviews” belongs to a separate Border Gateway Protocol (BGP) issue: an operator tries to make a remote AS prefer one inbound path using LOCAL_PREF that the remote eBGP peer never receives. It does not explain the condition tested here.

D:

“Monitor AS-path anomalies and validate inter-AS topology changes before enabling export” belongs to a separate Border Gateway Protocol (BGP) issue: the local AS appears in a received external BGP AS_PATH and the route is rejected despite valid prefix reachability. It does not explain the condition tested here.

Question 1152

The team believes it has resolved this Junos issue: Guest users on an EX switch see no captive login page because browser HTTP redirects are not being applied on the intended VLAN. Which observation best verifies the specific intended result?

  1. The registered device is authorized with limited access; an unknown MAC remains blocked.
  2. The switch reports an authorized session with the intended VLAN and access policy.
  3. The user sees a valid login prompt and receives only the approved post-login policy.
  4. A nonresponding guest gets its intended limited VLAN while invalid credentials never receive guest privilege.

Explanation

Correct Answer

C:

The user sees a valid login prompt and receives only the approved post-login policy. This checks the relevant result after inspect switch captive portal attachment, redirect reachability and completion flow for a test guest.

Incorrect Answers

A:

“The registered device is authorized with limited access; an unknown MAC remains blocked” belongs to a separate Layer 2 Authentication and Access Control issue: a non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. It does not explain the condition tested here.

B:

“The switch reports an authorized session with the intended VLAN and access policy” belongs to a separate Layer 2 Authentication and Access Control issue: a switch receives successful RADIUS Access-Accept but the user still lands in an unexpected VLAN because the dynamic assignment is not supported on that platform. It does not explain the condition tested here.

D:

“A nonresponding guest gets its intended limited VLAN while invalid credentials never receive guest privilege” belongs to a separate Layer 2 Authentication and Access Control issue: a credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants. It does not explain the condition tested here.

Question 1153

To prevent recurrence of this precise networking failure, which practice should be adopted? A campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly.

  1. Test each critical VLAN's root bridge and forwarding path after VSTP updates.
  2. Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews.
  3. Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned.
  4. Test private-port isolation and uplink reachability after access topology changes.

Explanation

Correct Answer

C:

Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned. This guards against MVRP registrations can persist where membership state or participation has not been updated consistently.

Incorrect Answers

A:

“Test each critical VLAN's root bridge and forwarding path after VSTP updates” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.

B:

“Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews” belongs to a separate Ethernet Switching and Spanning Tree issue: a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. It does not explain the condition tested here.

D:

“Test private-port isolation and uplink reachability after access topology changes” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It does not explain the condition tested here.

Question 1154

A Junos enterprise team investigates this incident: An eBGP import policy unexpectedly accepts more-specific prefixes outside the approved customer allocation. Which technical explanation most directly identifies the cause or design principle?

  1. BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops.
  2. iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology.
  3. BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
  4. Routing-policy term order and terminal actions determine whether later conditions are evaluated.

Explanation

Correct Answer

C:

BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately. The appropriate response is to use precise route-filter match conditions and explicit rejection of unauthorized more-specific routes.

Incorrect Answers

A:

“BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops” belongs to a separate Border Gateway Protocol (BGP) issue: an IPv6 transit prefix is hidden because its next-hop address is absent from the correct IPv6 routing table. It does not explain the condition tested here.

B:

“iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology” belongs to a separate Border Gateway Protocol (BGP) issue: a route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster. It does not explain the condition tested here.

D:

“Routing-policy term order and terminal actions determine whether later conditions are evaluated” belongs to a separate Border Gateway Protocol (BGP) issue: a route with a permissive policy term is accepted before a later deny term can block it. It does not explain the condition tested here.

Question 1155

The team believes it has resolved this Junos issue: A route with a permissive policy term is accepted before a later deny term can block it. Which observation best verifies the specific intended result?

  1. The selected BGP route reflects the intended higher LOCAL_PREF, and traceroute follows the approved exit.
  2. The previously hidden BGP prefix resolves its next hop and becomes an eligible route.
  3. The unauthorized route is rejected while intended export cases still match the proper terms.
  4. The IPv6 BGP route becomes eligible and forwards over an IPv6-resolvable next hop.

Explanation

Correct Answer

C:

The unauthorized route is rejected while intended export cases still match the proper terms. This checks the relevant result after put specific deny conditions before broad acceptance, and test the policy with representative routes.

Incorrect Answers

A:

“The selected BGP route reflects the intended higher LOCAL_PREF, and traceroute follows the approved exit” belongs to a separate Border Gateway Protocol (BGP) issue: an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path. It does not explain the condition tested here.

B:

“The previously hidden BGP prefix resolves its next hop and becomes an eligible route” belongs to a separate Border Gateway Protocol (BGP) issue: a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. It does not explain the condition tested here.

D:

“The IPv6 BGP route becomes eligible and forwards over an IPv6-resolvable next hop” belongs to a separate Border Gateway Protocol (BGP) issue: an IPv6 BGP peer receives a route with an unreachable IPv6 next hop despite an otherwise valid inet6 unicast advertisement. It does not explain the condition tested here.

Question 1156

A Junos enterprise team investigates this incident: A stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work. Which technical explanation most directly identifies the cause or design principle?

  1. Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture.
  2. An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic.
  3. MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
  4. Policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked.

Explanation

Correct Answer

B:

An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic. The appropriate response is to compare source-route preference with actual multicast ingress and restore a consistent authorized upstream path.

Incorrect Answers

A:

“Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture” belongs to a separate IP Multicast issue: a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it. It does not explain the condition tested here.

C:

“MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points” belongs to a separate IP Multicast issue: a receiver domain requires discovery of sources known behind another RP, yet inter-RP source information exchange is absent. It does not explain the condition tested here.

D:

“Policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked” belongs to a separate IP Multicast issue: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It does not explain the condition tested here.

Question 1157

A Junos enterprise team investigates this incident: A switch rollout splits a team that should communicate within one PVLAN community, while protecting it from another community. Which technical explanation most directly identifies the cause or design principle?

  1. Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.
  2. VSTP provides per-VLAN spanning-tree behavior for compatibility and path control when the design and platform support it.
  3. Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
  4. A private VLAN community allows permitted communication within its community; isolated behavior is stricter.

Explanation

Correct Answer

D:

A private VLAN community allows permitted communication within its community; isolated behavior is stricter. The appropriate response is to map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated.

Incorrect Answers

A:

“Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough” belongs to a separate Ethernet Switching and Spanning Tree issue: an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently. It does not explain the condition tested here.

B:

“VSTP provides per-VLAN spanning-tree behavior for compatibility and path control when the design and platform support it” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.

C:

“Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet. It does not explain the condition tested here.

Question 1158

To prevent recurrence of this precise networking failure, which practice should be adopted? After a RADIUS outage, the access switch opens ports broadly instead of applying the approved restricted server-fail VLAN.

  1. Verify RADIUS attribute handling and model/release feature support before rolling out dynamic assignment.
  2. Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance.
  3. Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises.
  4. Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding.

Explanation

Correct Answer

C:

Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises. This guards against server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access.

Incorrect Answers

A:

“Verify RADIUS attribute handling and model/release feature support before rolling out dynamic assignment” belongs to a separate Layer 2 Authentication and Access Control issue: a switch receives successful RADIUS Access-Accept but the user still lands in an unexpected VLAN because the dynamic assignment is not supported on that platform. It does not explain the condition tested here.

B:

“Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance” belongs to a separate Layer 2 Authentication and Access Control issue: guest users on an EX switch see no captive login page because browser HTTP redirects are not being applied on the intended VLAN. It does not explain the condition tested here.

D:

“Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding” belongs to a separate Layer 2 Authentication and Access Control issue: a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend. It does not explain the condition tested here.

Question 1159

Which suggested shortcut would be especially unsafe for this exact situation? A high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously.

  1. Include LLDP-MED capabilities and network-policy TLVs in phone-vendor acceptance testing.
  2. Include end-to-end marking tests when deploying voice VLANs and new phone models.
  3. Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power.
  4. Test both tagged phone frames and untagged PC frames during phone-port commissioning.

Explanation

Correct Answer

C:

The tempting alternative fails because PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status. The supported action is to check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power.

Incorrect Answers

A:

That prevention measure relates to a newly deployed IP phone joins the data network because the switch does not advertise the intended voice VLAN through LLDP-MED.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN.; it is not the unsafe shortcut described here.

Question 1160

To prevent recurrence of this precise networking failure, which practice should be adopted? A router's OSPF neighbor restarts repeatedly because duplicate router IDs were assigned to different routing nodes.

  1. Reserve router IDs from a centrally managed inventory before zero-touch provisioning.
  2. Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance.
  3. Test one allowed and one forbidden route against each export policy term before deployment.
  4. Keep IPv4 and IPv6 routing verification separate for dual-stack maintenance.

Explanation

Correct Answer

A:

Reserve router IDs from a centrally managed inventory before zero-touch provisioning. This guards against OSPF identifies routers by unique router ID; collisions can destabilize LSDB and adjacency behavior.

Incorrect Answers

B:

“Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance” belongs to a separate Interior Gateway Protocols (IGPs) issue: a replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring. It does not explain the condition tested here.

C:

“Test one allowed and one forbidden route against each export policy term before deployment” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated. It does not explain the condition tested here.

D:

“Keep IPv4 and IPv6 routing verification separate for dual-stack maintenance” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.