Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 118

Question 1170

Which suggested shortcut would be especially unsafe for this exact situation? An ABR starts leaking a management static route into the enterprise IGP after a permissive export term was introduced.

  1. Keep timer settings in shared configuration templates and validate both directions before rollout.
  2. Keep IPv4 and IPv6 routing verification separate for dual-stack maintenance.
  3. Validate active logical-interface mappings and IPv6 adjacency as part of change acceptance.
  4. Set a blanket export accept action and rely on other routers to ignore sensitive prefixes.

Explanation

Correct Answer

D:

The tempting alternative fails because unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability. The supported action is to restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.

Incorrect Answers

A:

That prevention measure relates to two OSPF routers on a shared transit segment report different Hello and dead intervals and never establish adjacency.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear.; it is not the unsafe shortcut described here.

Question 1171

The team believes it has resolved this Junos issue: A visitor portal redirects browser traffic but never releases the user to the approved network after authentication. Which observation best verifies the specific intended result?

  1. Both intended endpoints receive their authorized VLAN/policy without permitting unapproved devices.
  2. The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint.
  3. The known device reaches only permitted destinations and cannot reach employee or management resources.
  4. The user sees a valid login prompt and receives only the approved post-login policy.

Explanation

Correct Answer

D:

The user sees a valid login prompt and receives only the approved post-login policy. This checks the relevant result after inspect switch captive portal attachment, redirect reachability and completion flow for a test guest.

Incorrect Answers

A:

“Both intended endpoints receive their authorized VLAN/policy without permitting unapproved devices” belongs to a separate Layer 2 Authentication and Access Control issue: a telephony desk requires multiple authenticated identities while the switch policy allows only one active supplicant. It does not explain the condition tested here.

B:

“The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint” belongs to a separate Layer 2 Authentication and Access Control issue: a RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. It does not explain the condition tested here.

C:

“The known device reaches only permitted destinations and cannot reach employee or management resources” belongs to a separate Layer 2 Authentication and Access Control issue: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It does not explain the condition tested here.

Question 1172

Select THREE complementary corrective, verification, or preventive controls for this scenario: A multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior.

  1. Use two unrelated ESIs for one logical Ethernet segment and assume EVPN coordinates them as one.
  2. Align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes.
  3. Read a Type 1 Ethernet auto-discovery update as the definitive source of every individual host MAC address.
  4. Both peers report a consistent Ethernet segment and failover preserves authorized connectivity.
  5. Audit ESI consistency and platform-supported multihoming mode across paired leafs.
  6. Reuse one VNI for unrelated tenants and assume local VLAN names alone prevent overlay mixing.

Explanation

Correct Answers

B:

Correction: EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence.

D:

Confirmation: Align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes.

E:

Prevention of recurrence: EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence.

Incorrect Answers

A:

“Use two unrelated ESIs for one logical Ethernet segment and assume EVPN coordinates them as one” does not address EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence.

C:

“Read a Type 1 Ethernet auto-discovery update as the definitive source of every individual host MAC address” is an unsafe response to a different problem: a fabric advertises Type 3 routes and claims this proves specific remote host MACs are reachable. It is not a valid fix here.

F:

“Reuse one VNI for unrelated tenants and assume local VLAN names alone prevent overlay mixing” is an unsafe response to a different problem: a campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. It is not a valid fix here.

Question 1173

Which suggested shortcut would be especially unsafe for this exact situation? A troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings.

  1. Include underlay loopback reachability and MTU checks in VXLAN overlay deployment QA.
  2. Maintain a central VNI registry and test cross-tenant isolation on each leaf rollout.
  3. Test multihoming election and per-VLAN failover after attaching new dual-homed devices.
  4. Read a Type 1 Ethernet auto-discovery update as the definitive source of every individual host MAC address.

Explanation

Correct Answer

D:

The tempting alternative fails because EVPN route types carry different information: Type 1 Ethernet auto-discovery, Type 2 MAC/IP, Type 3 inclusive multicast. The supported action is to inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally.

Incorrect Answers

A:

That prevention measure relates to a new leaf imports VNI reachability but packets disappear because its VXLAN tunnel endpoint IP is unresolved.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to an EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior.; it is not the unsafe shortcut described here.

Question 1174

Which suggested shortcut would be especially unsafe for this exact situation? An ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP.

  1. Check multicast and unicast topology alignment whenever routing paths or metrics change.
  2. Keep an approved multicast group allocation and test boundary enforcement after routing changes.
  3. Assume IGMP membership on the access switch alone builds an end-to-end PIM ASM tree.
  4. Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.

Explanation

Correct Answer

C:

The tempting alternative fails because PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service. The supported action is to check group-to-RP mapping and RP reachability, then repair the RP discovery or explicit mapping.

Incorrect Answers

A:

That prevention measure relates to multicast packets arrive on the wrong uplink after unicast routing changes and are dropped by the campus core.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route.; it is not the unsafe shortcut described here.

Question 1175

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling.

  1. Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy.
  2. Assume more queues automatically improve latency even if control traffic remains mapped to a congested queue.
  3. Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic.
  4. Apply the appropriate interface rewrite rule and verify the contract-specific egress code points.
  5. Set the maximum drop probability at near-empty queue levels and expect no early loss.

Explanation

Correct Answers

C:

Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic. The specific steps required are to apply the appropriate interface rewrite rule and verify the contract-specific egress code points.

D:

Apply the appropriate interface rewrite rule and verify the contract-specific egress code points. This addresses the dependency that Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings.

Incorrect Answers

A:

“Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy” does not address Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings.

B:

“Assume more queues automatically improve latency even if control traffic remains mapped to a congested queue” is an unsafe response to a different problem: a forwarding-class configuration sends critical routing packets to a queue used for bulk backups and adjacency stability degrades under load. It is not a valid fix here.

E:

“Set the maximum drop probability at near-empty queue levels and expect no early loss” is an unsafe response to a different problem: a RED drop profile is applied too aggressively and drops packets even under moderate load. It is not a valid fix here.

Question 1176

To prevent recurrence of this precise networking failure, which practice should be adopted? A security function needs to classify a subset of traffic by source and destination criteria rather than trusted external markings.

  1. Document trusted-marking boundaries and test both matched and unmatched multifield traffic.
  2. Test both average-rate enforcement and microburst tolerance for new policer profiles.
  3. Validate classifier, scheduler map and interface association as a complete CoS chain.
  4. Differentiate ingress policing from egress shaping when designing bandwidth controls.

Explanation

Correct Answer

A:

Document trusted-marking boundaries and test both matched and unmatched multifield traffic. This guards against multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification.

Incorrect Answers

B:

“Test both average-rate enforcement and microburst tolerance for new policer profiles” belongs to a separate Class of Service (CoS) issue: an uplink meets long-term bandwidth policy but legitimate short bursts exceed the token-bucket allowance. It does not explain the condition tested here.

C:

“Validate classifier, scheduler map and interface association as a complete CoS chain” belongs to a separate Class of Service (CoS) issue: a low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk. It does not explain the condition tested here.

D:

“Differentiate ingress policing from egress shaping when designing bandwidth controls” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.

Question 1177

To prevent recurrence of this precise networking failure, which practice should be adopted? A campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests.

  1. Review interdomain source-advertisement scope and MSDP peer availability for ASM deployments.
  2. Include source address changes in SSM subscription-management procedures.
  3. Run both allow and deny group tests against multicast policy whenever prefixes are revised.
  4. Keep an approved multicast group allocation and test boundary enforcement after routing changes.

Explanation

Correct Answer

B:

Include source address changes in SSM subscription-management procedures. This guards against ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender.

Incorrect Answers

A:

“Review interdomain source-advertisement scope and MSDP peer availability for ASM deployments” belongs to a separate IP Multicast issue: a multicast source is active in a different PIM domain but the local ASM RP never learns the source mapping. It does not explain the condition tested here.

C:

“Run both allow and deny group tests against multicast policy whenever prefixes are revised” belongs to a separate IP Multicast issue: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It does not explain the condition tested here.

D:

“Keep an approved multicast group allocation and test boundary enforcement after routing changes” belongs to a separate IP Multicast issue: a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. It does not explain the condition tested here.

Question 1178

A Junos enterprise team investigates this incident: A backup traffic queue consumes too much buffer and latency-sensitive applications starve during peak bursts. Which technical explanation most directly identifies the cause or design principle?

  1. Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification.
  2. Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.
  3. A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress.
  4. Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress.

Explanation

Correct Answer

D:

Queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress. The appropriate response is to review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment.

Incorrect Answers

A:

“Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification” belongs to a separate Class of Service (CoS) issue: a security function needs to classify a subset of traffic by source and destination criteria rather than trusted external markings. It does not explain the condition tested here.

B:

“Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic” belongs to a separate Class of Service (CoS) issue: a traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. It does not explain the condition tested here.

C:

“A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.

Question 1179

The team believes it has resolved this Junos issue: A non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. Which observation best verifies the specific intended result?

  1. The registered device is authorized with limited access; an unknown MAC remains blocked.
  2. A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state.
  3. Validation shows only supported options in use and the intended access-denial/fallback behavior.
  4. The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint.

Explanation

Correct Answer

A:

The registered device is authorized with limited access; an unknown MAC remains blocked. This checks the relevant result after configure supported MAC RADIUS under least-privilege policy and register the device MAC with the approved service.

Incorrect Answers

B:

“A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state” belongs to a separate Layer 2 Authentication and Access Control issue: a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend. It does not explain the condition tested here.

C:

“Validation shows only supported options in use and the intended access-denial/fallback behavior” belongs to a separate Layer 2 Authentication and Access Control issue: an access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces. It does not explain the condition tested here.

D:

“The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint” belongs to a separate Layer 2 Authentication and Access Control issue: a switch logs EAP timeout while the endpoint has no 802.1X supplicant, yet the operator rotates valid RADIUS passwords repeatedly. It does not explain the condition tested here.

Question 1180

The team believes it has resolved this Junos issue: A host moves between leafs and the destination leaf still forwards toward the previous MAC location. Which observation best verifies the specific intended result?

  1. The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended.
  2. Both peers report a consistent Ethernet segment and failover preserves authorized connectivity.
  3. The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding.
  4. Tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated.

Explanation

Correct Answer

C:

The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding. This checks the relevant result after check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.

Incorrect Answers

A:

“The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended” belongs to a separate EVPN issue: a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback. It does not explain the condition tested here.

B:

“Both peers report a consistent Ethernet segment and failover preserves authorized connectivity” belongs to a separate EVPN issue: a shared Ethernet segment loses its fast convergence properties after an ESI-LAG peer receives an inconsistent configuration. It does not explain the condition tested here.

D:

“Tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated” belongs to a separate EVPN issue: a fabric uses conflicting VLAN-to-VNI mappings on two leaf switches, bridging different tenant segments together. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.