100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 360
The team believes it has resolved this Junos issue: An aggregation broadcast VLAN has a DR/BDR placement that conflicts with the approved design after a maintenance reboot. Which observation best verifies the specific intended result?
- The remote inet6.0 table learns the intended loopback and reachability testing succeeds.
- Neighbor states and DR/BDR assignments match the approved design following a managed election.
- Only authorized static prefixes appear as OSPF externals; management prefixes remain local.
- The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency.
Explanation
Correct Answer
B:Neighbor states and DR/BDR assignments match the approved design following a managed election. This checks the relevant result after inspect network type, interface priority and existing election state, then plan a controlled DR/BDR change.
Incorrect Answers
A:“The remote inet6.0 table learns the intended loopback and reachability testing succeeds” belongs to a separate Interior Gateway Protocols (IGPs) issue: a replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring. It does not explain the condition tested here.
C:“Only authorized static prefixes appear as OSPF externals; management prefixes remain local” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR starts leaking a management static route into the enterprise IGP after a permissive export term was introduced. It does not explain the condition tested here.
D:“The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6 route learned through OSPFv3 is absent from the forwarding table because a more preferred static route covers the same prefix. It does not explain the condition tested here.
Question 361
A Junos enterprise team investigates this incident: An enterprise fallback design accidentally places unauthenticated users into the production network when all RADIUS servers fail. Which technical explanation most directly identifies the cause or design principle?
- Server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access.
- Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary.
- 802.1X authorization depends on the authenticator, supplicant and authentication-server conversation being correctly connected.
- MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X.
Explanation
Correct Answer
A:Server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access. The appropriate response is to use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
Incorrect Answers
B:“Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary” belongs to a separate Layer 2 Authentication and Access Control issue: an EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization. It does not explain the condition tested here.
C:“802.1X authorization depends on the authenticator, supplicant and authentication-server conversation being correctly connected” belongs to a separate Layer 2 Authentication and Access Control issue: a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. It does not explain the condition tested here.
D:“MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X” belongs to a separate Layer 2 Authentication and Access Control issue: a non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. It does not explain the condition tested here.
Question 362
The team believes it has resolved this Junos issue: A corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. Which observation best verifies the specific intended result?
- Validation shows only supported options in use and the intended access-denial/fallback behavior.
- The known device reaches only permitted destinations and cannot reach employee or management resources.
- A nonresponding guest gets its intended limited VLAN while invalid credentials never receive guest privilege.
- A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state.
Explanation
Correct Answer
D:A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state. This checks the relevant result after inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
Incorrect Answers
A:“Validation shows only supported options in use and the intended access-denial/fallback behavior” belongs to a separate Layer 2 Authentication and Access Control issue: an engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them. It does not explain the condition tested here.
B:“The known device reaches only permitted destinations and cannot reach employee or management resources” belongs to a separate Layer 2 Authentication and Access Control issue: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It does not explain the condition tested here.
C:“A nonresponding guest gets its intended limited VLAN while invalid credentials never receive guest privilege” belongs to a separate Layer 2 Authentication and Access Control issue: a credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants. It does not explain the condition tested here.
Question 363
The team believes it has resolved this Junos issue: BGP peers exchange IPv4 NLRI correctly but a planned IPv6 customer route never appears in inet6.0. Which observation best verifies the specific intended result?
- Positive and negative prefix tests traverse the expected policy terms and produce approved import/export outcomes.
- The chosen best path follows the documented attribute ordering rather than a single observed MED value.
- Route detail shows a reachable next hop and end-to-end forwarding through the intended border router.
- The expected IPv6 prefix is received in inet6.0 while IPv4 route exchange remains unchanged.
Explanation
Correct Answer
D:The expected IPv6 prefix is received in inet6.0 while IPv4 route exchange remains unchanged. This checks the relevant result after enable the intended inet6 family consistently on eligible BGP peers and verify route policy and inet6.0.
Incorrect Answers
A:“Positive and negative prefix tests traverse the expected policy terms and produce approved import/export outcomes” belongs to a separate Border Gateway Protocol (BGP) issue: a route policy lacks an explicit intended default action, and unmatched BGP prefixes behave differently than planned. It does not explain the condition tested here.
B:“The chosen best path follows the documented attribute ordering rather than a single observed MED value” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.
C:“Route detail shows a reachable next hop and end-to-end forwarding through the intended border router” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP egress advertisement forwards a transit next hop that branch routers cannot resolve, creating traffic blackholes. It does not explain the condition tested here.
Question 364
The team believes it has resolved this Junos issue: A new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. Which observation best verifies the specific intended result?
- The desired received prefix is accepted and active while intentionally blocked prefixes stay rejected.
- The selected BGP route reflects the intended higher LOCAL_PREF, and traceroute follows the approved exit.
- The previously hidden BGP prefix resolves its next hop and becomes an eligible route.
- After policy correction, chosen path and attribute ordering match documented routing intent.
Explanation
Correct Answer
C:The previously hidden BGP prefix resolves its next hop and becomes an eligible route. This checks the relevant result after restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.
Incorrect Answers
A:“The desired received prefix is accepted and active while intentionally blocked prefixes stay rejected” belongs to a separate Border Gateway Protocol (BGP) issue: a Junos route is hidden by import policy, but the team troubleshoots only local physical interfaces. It does not explain the condition tested here.
B:“The selected BGP route reflects the intended higher LOCAL_PREF, and traceroute follows the approved exit” belongs to a separate Border Gateway Protocol (BGP) issue: two iBGP exits offer equal reachable routes but the one with higher LOCAL_PREF is not the egress an operator expected. It does not explain the condition tested here.
D:“After policy correction, chosen path and attribute ordering match documented routing intent” belongs to a separate Border Gateway Protocol (BGP) issue: a router prefers a longer AS path when a higher LOCAL_PREF makes that route win, surprising the transit team. It does not explain the condition tested here.
Question 365
The team believes it has resolved this Junos issue: A troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. Which observation best verifies the specific intended result?
- The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types.
- The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended.
- BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates.
- Both peers report a consistent Ethernet segment and failover preserves authorized connectivity.
Explanation
Correct Answer
A:The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types. This checks the relevant result after inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally.
Incorrect Answers
B:“The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended” belongs to a separate EVPN issue: a new leaf imports VNI reachability but packets disappear because its VXLAN tunnel endpoint IP is unresolved. It does not explain the condition tested here.
C:“BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates” belongs to a separate EVPN issue: an EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. It does not explain the condition tested here.
D:“Both peers report a consistent Ethernet segment and failover preserves authorized connectivity” belongs to a separate EVPN issue: a multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. It does not explain the condition tested here.
Question 366
To prevent recurrence of this precise networking failure, which practice should be adopted? A business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class.
- Keep queue drop-profile acceptance tests and monitor production congestion before broad rollout.
- Establish congestion thresholds and monitor starvation as part of queue-priority design.
- Audit DSCP preservation and remarking at untrusted edge boundaries.
- Test marking, PLP assignment and drop policy together rather than checking only DSCP fields.
Explanation
Correct Answer
D:Test marking, PLP assignment and drop policy together rather than checking only DSCP fields. This guards against packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior.
Incorrect Answers
A:“Keep queue drop-profile acceptance tests and monitor production congestion before broad rollout” belongs to a separate Class of Service (CoS) issue: a RED drop profile is applied too aggressively and drops packets even under moderate load. It does not explain the condition tested here.
B:“Establish congestion thresholds and monitor starvation as part of queue-priority design” belongs to a separate Class of Service (CoS) issue: two queues use the same scheduler priority, but the business expects one to always win during contention. It does not explain the condition tested here.
C:“Audit DSCP preservation and remarking at untrusted edge boundaries” belongs to a separate Class of Service (CoS) issue: a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice. It does not explain the condition tested here.
Question 367
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A switch logs EAP timeout while the endpoint has no 802.1X supplicant, yet the operator rotates valid RADIUS passwords repeatedly.
- Give MAC-authenticated devices the same unrestricted access as strongly authenticated employees.
- The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint.
- Rotate every user's password without checking whether the endpoint sent an EAP response at all.
- Add a static DNS record and assume it substitutes for captive-portal authentication and authorization.
- Inspect packet exchange and classify the endpoint before selecting a supported fallback method.
Explanation
Correct Answers
B:The observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint. The specific steps required are to inspect packet exchange and classify the endpoint before selecting a supported fallback method.
E:Inspect packet exchange and classify the endpoint before selecting a supported fallback method. This addresses the dependency that supplicant absence is a distinct failure from an invalid credential or unreachable authentication server.
Incorrect Answers
A:“Give MAC-authenticated devices the same unrestricted access as strongly authenticated employees” is an unsafe response to a different problem: a MAC RADIUS policy authenticates a known camera but applies the broad employee VLAN instead of a camera-only network. It is not a valid fix here.
C:“Rotate every user's password without checking whether the endpoint sent an EAP response at all” does not address supplicant absence is a distinct failure from an invalid credential or unreachable authentication server.
D:“Add a static DNS record and assume it substitutes for captive-portal authentication and authorization” is an unsafe response to a different problem: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It is not a valid fix here.
Question 368
Which suggested shortcut would be especially unsafe for this exact situation? An OSPF neighbor remains Down because the routed transit interface was left passive after a site template rollout.
- Make every edge interface active to OSPF regardless of whether a routing peer exists.
- Document expected external metrics and run primary/backup failover tests during policy changes.
- Test one allowed and one forbidden route against each export policy term before deployment.
- Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance.
Explanation
Correct Answer
A:The tempting alternative fails because making a link passive suppresses OSPF adjacency formation even when its prefix remains eligible for advertisement. The supported action is to remove passive behavior only from the approved router-to-router transit link and check Hello and neighbor states.
Incorrect Answers
B:That prevention measure relates to a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a branch default-route injection stops after a policy matches OSPF-learned routes instead of the intended local static.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring.; it is not the unsafe shortcut described here.
Question 369
To prevent recurrence of this precise networking failure, which practice should be adopted? A phone's LLDP-negotiated power demand exceeds its access port's allocated PoE limit and it repeatedly restarts.
- Review LLDP-MED state and phone compliance during access-switch template audits.
- Include end-to-end marking tests when deploying voice VLANs and new phone models.
- Synchronize switchport moves with maintained emergency location records.
- Validate PD power profiles and test peak draw rather than idle boot alone.
Explanation
Correct Answer
D:Validate PD power profiles and test peak draw rather than idle boot alone. This guards against physical PoE delivery and negotiated device power requirements must match switch and endpoint capabilities.
Incorrect Answers
A:“Review LLDP-MED state and phone compliance during access-switch template audits” belongs to a separate IP Telephony Features issue: a powered endpoint detects a Junos switch but fails to negotiate voice prioritization because only ordinary LLDP is enabled. It does not explain the condition tested here.
B:“Include end-to-end marking tests when deploying voice VLANs and new phone models” belongs to a separate IP Telephony Features issue: a voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. It does not explain the condition tested here.
C:“Synchronize switchport moves with maintained emergency location records” belongs to a separate IP Telephony Features issue: a campus changes a telephone port but LLDP-MED location data remains mapped to an old floor. It does not explain the condition tested here.
Question 370
To prevent recurrence of this precise networking failure, which practice should be adopted? A private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs.
- Track MSTP instance scale and maintain identical region parameters across participating switches.
- Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
- Test private-port isolation and uplink reachability after access topology changes.
- Keep explicit root priority policy and validate elections after device replacement.
Explanation
Correct Answer
B:Scope and monitor tunneled L2 control protocols to prevent control-plane abuse. This guards against layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.
Incorrect Answers
A:“Track MSTP instance scale and maintain identical region parameters across participating switches” belongs to a separate Ethernet Switching and Spanning Tree issue: a large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits. It does not explain the condition tested here.
C:“Test private-port isolation and uplink reachability after access topology changes” belongs to a separate Ethernet Switching and Spanning Tree issue: a lab uses one primary VLAN for many tenants but isolated access ports can still exchange Layer 2 frames after a misconfiguration. It does not explain the condition tested here.
D:“Keep explicit root priority policy and validate elections after device replacement” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests