100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 30
Which suggested shortcut would be especially unsafe for this exact situation? A laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab.
- Measure receiver interest and multicast forwarding state before scaling new one-to-many services.
- Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.
- Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
- Use a unique group name as the only security boundary and rely on routers to infer its scope.
Explanation
Correct Answer
D:The tempting alternative fails because multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy. The supported action is to configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
Incorrect Answers
A:That prevention measure relates to a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders.; it is not the unsafe shortcut described here.
Question 31
The team believes it has resolved this Junos issue: An IP phone uses the wrong location information for emergency response after a switch move. Which observation best verifies the specific intended result?
- The phone receives stable negotiated power and the chassis stays within its supported budget under peak load.
- The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN.
- Tagged voice packets retain the intended service class through the access and aggregation paths.
- The phone or location service reports the correct emergency location for the new access port.
Explanation
Correct Answer
D:The phone or location service reports the correct emergency location for the new access port. This checks the relevant result after update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port.
Incorrect Answers
A:“The phone receives stable negotiated power and the chassis stays within its supported budget under peak load” belongs to a separate IP Telephony Features issue: a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget. It does not explain the condition tested here.
B:“The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN” belongs to a separate IP Telephony Features issue: a phone-with-PC desk deployment lets the PC reach data services while the tagged voice stream is dropped by VLAN membership. It does not explain the condition tested here.
C:“Tagged voice packets retain the intended service class through the access and aggregation paths” belongs to a separate IP Telephony Features issue: a voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. It does not explain the condition tested here.
Question 32
A network change is required for the following specific situation: A RED drop profile is applied too aggressively and drops packets even under moderate load. Which corrective action is most appropriate?
- Use a permitted firewall or multifield classifier matching the approved traffic fields and assign its forwarding class.
- Apply a correctly scoped ingress policer with tested rate and burst values on the relevant flow.
- Review configured drop probability versus fill level and align the profile with acceptable congestion targets.
- Define a controlled rewrite map for each class and verify high-priority markings remain restricted.
Explanation
Correct Answer
C:Drop profiles and weighted random early detection influence probabilistic discard thresholds as queue fill rises. Verify this by checking that drop counters and queue utilization follow the intended curve through increasing load.
Incorrect Answers
A:“Use a permitted firewall or multifield classifier matching the approved traffic fields and assign its forwarding class” belongs to a separate Class of Service (CoS) issue: an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It does not explain the condition tested here.
B:“Apply a correctly scoped ingress policer with tested rate and burst values on the relevant flow” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.
D:“Define a controlled rewrite map for each class and verify high-priority markings remain restricted” belongs to a separate Class of Service (CoS) issue: a customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic. It does not explain the condition tested here.
Question 33
Which suggested shortcut would be especially unsafe for this exact situation? An engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them.
- Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding.
- Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance.
- Include downstream device count and authentication method in desk-port templates.
- Assume every 802.1X feature shown in an EX switch guide is identically supported in all Junos OS Evolved interfaces.
Explanation
Correct Answer
D:The tempting alternative fails because 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed. The supported action is to consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.
Incorrect Answers
A:That prevention measure relates to a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend.; it is not the unsafe shortcut described here.
B:That prevention measure relates to guest users on an EX switch see no captive login page because browser HTTP redirects are not being applied on the intended VLAN.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port.; it is not the unsafe shortcut described here.
Question 34
To prevent recurrence of this precise networking failure, which practice should be adopted? An ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP.
- Include source address changes in SSM subscription-management procedures.
- Maintain consistent RP mappings and failover tests across multicast routers.
- Test multicast source-path behavior under each failover case, not only unicast ping.
- Measure receiver interest and multicast forwarding state before scaling new one-to-many services.
Explanation
Correct Answer
B:Maintain consistent RP mappings and failover tests across multicast routers. This guards against PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
Incorrect Answers
A:“Include source address changes in SSM subscription-management procedures” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.
C:“Test multicast source-path behavior under each failover case, not only unicast ping” belongs to a separate IP Multicast issue: a redundant network changes the preferred route to the source while packets keep arriving on the other physical link. It does not explain the condition tested here.
D:“Measure receiver interest and multicast forwarding state before scaling new one-to-many services” belongs to a separate IP Multicast issue: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It does not explain the condition tested here.
Question 35
Which suggested shortcut would be especially unsafe for this exact situation? A campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests.
- Test RP failover and synchronization behavior before expanding Anycast RP.
- Test multicast source-path behavior under each failover case, not only unicast ping.
- Treat SSM group membership as source-agnostic and subscribe to the group without source information.
- Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.
Explanation
Correct Answer
C:The tempting alternative fails because ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender. The supported action is to update receiver memberships to use the approved source and group, and validate end-to-end (S,G) trees.
Incorrect Answers
A:That prevention measure relates to a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route.; it is not the unsafe shortcut described here.
Question 36
A Junos enterprise team investigates this incident: A branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. Which technical explanation most directly identifies the cause or design principle?
- IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges.
- OSPF identifies routers by unique router ID; collisions can destabilize LSDB and adjacency behavior.
- OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior.
- Area summarization scope must correctly cover the intended component networks; the wrong range can suppress or misrepresent reachability.
Explanation
Correct Answer
C:OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior. The appropriate response is to review external metric type and value at the originator, then apply the documented traffic-engineering policy.
Incorrect Answers
A:“IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.
B:“OSPF identifies routers by unique router ID; collisions can destabilize LSDB and adjacency behavior” belongs to a separate Interior Gateway Protocols (IGPs) issue: a router's OSPF neighbor restarts repeatedly because duplicate router IDs were assigned to different routing nodes. It does not explain the condition tested here.
D:“Area summarization scope must correctly cover the intended component networks; the wrong range can suppress or misrepresent reachability” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR stops advertising a branch prefix into the backbone after an OSPF area-range summary is configured incorrectly. It does not explain the condition tested here.
Question 37
A Junos enterprise team investigates this incident: A PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point. Which technical explanation most directly identifies the cause or design principle?
- Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow.
- Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.
- PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
- An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic.
Explanation
Correct Answer
C:PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service. The appropriate response is to check group-to-RP mapping and RP reachability, then repair the RP discovery or explicit mapping.
Incorrect Answers
A:“Source-specific multicast uses (S,G) membership semantics and generally avoids ASM rendezvous-point discovery for that flow” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.
B:“Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic” belongs to a separate IP Multicast issue: a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. It does not explain the condition tested here.
D:“An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic” belongs to a separate IP Multicast issue: a stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work. It does not explain the condition tested here.
Question 38
A network change is required for the following specific situation: A vendor handset discovers its neighbor using basic LLDP but does not learn the configured network policy for voice tagging. Which corrective action is most appropriate?
- Enable supported LLDP-MED network policy on the phone-facing port and verify advertisements and phone settings.
- Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
- Configure an approved voice VLAN on the port while keeping the PC data VLAN constrained.
- Check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power.
Explanation
Correct Answer
A:LLDP-MED extends device discovery with telephony-related network-policy TLVs that need compatible endpoint behavior. Verify this by checking that the handset learns the authorized voice VLAN and traffic is tagged and prioritized according to design.
Incorrect Answers
B:“Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media” belongs to a separate IP Telephony Features issue: a voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. It does not explain the condition tested here.
C:“Configure an approved voice VLAN on the port while keeping the PC data VLAN constrained” belongs to a separate IP Telephony Features issue: a phone-with-PC desk deployment lets the PC reach data services while the tagged voice stream is dropped by VLAN membership. It does not explain the condition tested here.
D:“Check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power” belongs to a separate IP Telephony Features issue: a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. It does not explain the condition tested here.
Question 39
Which suggested shortcut would be especially unsafe for this exact situation? An access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port.
- Review authorization policies for MAC endpoints against a least-privilege access matrix.
- Test multi-method paths including success, reject and timeout cases before deployment.
- Use a single unauthenticated open port for the phone and PC to bypass host-mode constraints.
- Track hardware, software edition and port family when standardizing access policies.
Explanation
Correct Answer
C:The tempting alternative fails because 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized. The supported action is to select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies.
Incorrect Answers
A:That prevention measure relates to a MAC RADIUS policy authenticates a known camera but applies the broad employee VLAN instead of a camera-only network.; it is not the unsafe shortcut described here.
B:That prevention measure relates to two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them.; it is not the unsafe shortcut described here.
Question 40
Which suggested shortcut would be especially unsafe for this exact situation? A multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior.
- Use two unrelated ESIs for one logical Ethernet segment and assume EVPN coordinates them as one.
- Validate EVPN Type 2 and Type 3 propagation separately in new VNI bring-up tests.
- Keep route-type purpose and acceptance checks in EVPN troubleshooting runbooks.
- Track route import, MAC mobility and aging during host migration tests.
Explanation
Correct Answer
A:The tempting alternative fails because EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence. The supported action is to align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes.
Incorrect Answers
B:That prevention measure relates to a bridge domain has valid unicast Type 2 entries yet remote VTEPs do not discover a new participating segment for BUM forwarding.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a host moves between leafs and the destination leaf still forwards toward the previous MAC location.; it is not the unsafe shortcut described here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests