Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 40

Question 390

Which suggested shortcut would be especially unsafe for this exact situation? A distribution node learns connected subnets but never sends Hello packets on its OSPF transit port due to passive-interface policy.

  1. Keep IPv4 and IPv6 routing verification separate for dual-stack maintenance.
  2. Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance.
  3. Test one allowed and one forbidden route against each export policy term before deployment.
  4. Make every edge interface active to OSPF regardless of whether a routing peer exists.

Explanation

Correct Answer

D:

The tempting alternative fails because making a link passive suppresses OSPF adjacency formation even when its prefix remains eligible for advertisement. The supported action is to remove passive behavior only from the approved router-to-router transit link and check Hello and neighbor states.

Incorrect Answers

A:

That prevention measure relates to an IPv6 branch outage is misdiagnosed using only IPv4 pings, despite OSPFv3 neighbors using IPv6 link-local messaging.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to OSPFv3 peering comes up but the desired IPv6 loopback is not in the routing database after a rollout.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to an OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated.; it is not the unsafe shortcut described here.

Question 391

The team believes it has resolved this Junos issue: An IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. Which observation best verifies the specific intended result?

  1. An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0.
  2. The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change.
  3. No router-ID collision appears and OSPF paths stabilize with expected next hops.
  4. The preferred primary route wins when healthy and the backup becomes active on a controlled failure.

Explanation

Correct Answer

A:

An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0. This checks the relevant result after move OSPFv3 participation to the correct active interface and verify neighbor and IPv6 RIB state.

Incorrect Answers

B:

“The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs. It does not explain the condition tested here.

C:

“No router-ID collision appears and OSPF paths stabilize with expected next hops” belongs to a separate Interior Gateway Protocols (IGPs) issue: a router's OSPF neighbor restarts repeatedly because duplicate router IDs were assigned to different routing nodes. It does not explain the condition tested here.

D:

“The preferred primary route wins when healthy and the backup becomes active on a controlled failure” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF policy update redistributes a route without an appropriate external metric, shifting traffic to a slow backup. It does not explain the condition tested here.

Question 392

Which suggested shortcut would be especially unsafe for this exact situation? A large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits.

  1. Create an independent VSTP instance for every VLAN without checking platform scaling limits.
  2. Include MVRP adjacency and registration checks in trunk-change reviews.
  3. Document primary/secondary VLAN mappings and test permitted peer groups and isolation boundaries.
  4. Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries.

Explanation

Correct Answer

A:

The tempting alternative fails because MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control. The supported action is to create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior.

Incorrect Answers

B:

That prevention measure relates to a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure.; it is not the unsafe shortcut described here.

Question 393

To prevent recurrence of this precise networking failure, which practice should be adopted? An uplink becomes a region boundary unexpectedly after an administrator changes an MSTP configuration name on only one switch.

  1. Include MVRP adjacency and registration checks in trunk-change reviews.
  2. Maintain representative match and nonmatch tests for filter-based VLAN policies.
  3. Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries.
  4. Version-control MSTP name, revision and VLAN mapping as one change unit.

Explanation

Correct Answer

D:

Version-control MSTP name, revision and VLAN mapping as one change unit. This guards against MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map.

Incorrect Answers

A:

“Include MVRP adjacency and registration checks in trunk-change reviews” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. It does not explain the condition tested here.

B:

“Maintain representative match and nonmatch tests for filter-based VLAN policies” belongs to a separate Ethernet Switching and Spanning Tree issue: a policy-based VLAN filter moves matching device traffic to a quarantine VLAN but a rule fails to match the intended MAC or packet fields. It does not explain the condition tested here.

C:

“Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.

Question 394

To prevent recurrence of this precise networking failure, which practice should be adopted? A switch assigns a misconfigured laptop with incorrect EAP credentials to a VLAN intended only for devices that never attempt 802.1X.

  1. Include downstream device count and authentication method in desk-port templates.
  2. Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance.
  3. Document and test EAP timeout, explicit rejection and server-unavailable cases separately.
  4. Separate EAP silence, reject and timeout counters in authentication operational monitoring.

Explanation

Correct Answer

C:

Document and test EAP timeout, explicit rejection and server-unavailable cases separately. This guards against guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.

Incorrect Answers

A:

“Include downstream device count and authentication method in desk-port templates” belongs to a separate Layer 2 Authentication and Access Control issue: an access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It does not explain the condition tested here.

B:

“Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance” belongs to a separate Layer 2 Authentication and Access Control issue: guest users on an EX switch see no captive login page because browser HTTP redirects are not being applied on the intended VLAN. It does not explain the condition tested here.

D:

“Separate EAP silence, reject and timeout counters in authentication operational monitoring” belongs to a separate Layer 2 Authentication and Access Control issue: a RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. It does not explain the condition tested here.

Question 395

To prevent recurrence of this precise networking failure, which practice should be adopted? An access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces.

  1. Track hardware, software edition and port family when standardizing access policies.
  2. Separate EAP silence, reject and timeout counters in authentication operational monitoring.
  3. Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions.
  4. Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding.

Explanation

Correct Answer

A:

Track hardware, software edition and port family when standardizing access policies. This guards against 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed.

Incorrect Answers

B:

“Separate EAP silence, reject and timeout counters in authentication operational monitoring” belongs to a separate Layer 2 Authentication and Access Control issue: a RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. It does not explain the condition tested here.

C:

“Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions” belongs to a separate Layer 2 Authentication and Access Control issue: a printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy. It does not explain the condition tested here.

D:

“Monitor RADIUS reachability and validate each switch's authentication server profile during onboarding” belongs to a separate Layer 2 Authentication and Access Control issue: a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. It does not explain the condition tested here.

Question 396

The team believes it has resolved this Junos issue: Two OSPF routers on a shared transit segment report different Hello and dead intervals and never establish adjacency. Which observation best verifies the specific intended result?

  1. The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency.
  2. Stable Hellos and Full neighbor state persist through repeated protocol interval checks.
  3. The remote inet6.0 table learns the intended loopback and reachability testing succeeds.
  4. Only authorized static prefixes appear as OSPF externals; management prefixes remain local.

Explanation

Correct Answer

B:

Stable Hellos and Full neighbor state persist through repeated protocol interval checks. This checks the relevant result after compare OSPF interface timers and align the two peers to approved Hello and dead values.

Incorrect Answers

A:

“The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6 route learned through OSPFv3 is absent from the forwarding table because a more preferred static route covers the same prefix. It does not explain the condition tested here.

C:

“The remote inet6.0 table learns the intended loopback and reachability testing succeeds” belongs to a separate Interior Gateway Protocols (IGPs) issue: a replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring. It does not explain the condition tested here.

D:

“Only authorized static prefixes appear as OSPF externals; management prefixes remain local” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR starts leaking a management static route into the enterprise IGP after a permissive export term was introduced. It does not explain the condition tested here.

Question 397

Which suggested shortcut would be especially unsafe for this exact situation? A host moves between leafs and the destination leaf still forwards toward the previous MAC location.

  1. Include underlay loopback reachability and MTU checks in VXLAN overlay deployment QA.
  2. Test multihoming election and per-VLAN failover after attaching new dual-homed devices.
  3. Include encapsulation headroom and path MTU tests in EVPN-VXLAN design validation.
  4. Assume a data-plane VXLAN tunnel automatically updates every remote leaf's EVPN MAC reachability without Type 2 control-plane exchange.

Explanation

Correct Answer

D:

The tempting alternative fails because EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane. The supported action is to check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.

Incorrect Answers

A:

That prevention measure relates to a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a dual-attached Ethernet segment experiences persistent duplicates during link recovery because multihoming election or ESI state differs.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads.; it is not the unsafe shortcut described here.

Question 398

Select THREE complementary corrective, verification, or preventive controls for this scenario: An engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them.

  1. Track hardware, software edition and port family when standardizing access policies.
  2. Use a single unauthenticated open port for the phone and PC to bypass host-mode constraints.
  3. Assume every 802.1X feature shown in an EX switch guide is identically supported in all Junos OS Evolved interfaces.
  4. Grant unbounded port access to all endpoints instead of diagnosing the RADIUS/EAP path.
  5. Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.
  6. Validation shows only supported options in use and the intended access-denial/fallback behavior.

Explanation

Correct Answers

A:

Prevention of recurrence: 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed.

E:

Correction: 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed.

F:

Confirmation: Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.

Incorrect Answers

B:

“Use a single unauthenticated open port for the phone and PC to bypass host-mode constraints” is an unsafe response to a different problem: an access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It is not a valid fix here.

C:

“Assume every 802.1X feature shown in an EX switch guide is identically supported in all Junos OS Evolved interfaces” does not address 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed.

D:

“Grant unbounded port access to all endpoints instead of diagnosing the RADIUS/EAP path” is an unsafe response to a different problem: a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend. It is not a valid fix here.

Question 399

A Junos enterprise team investigates this incident: A desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. Which technical explanation most directly identifies the cause or design principle?

  1. Voice/data split depends on compatible VLAN membership, accepted 802.1Q tagging and endpoint network policy.
  2. Base LLDP discovery and LLDP-MED telephony advertisement are distinct capabilities and may require separate enablement.
  3. PoE priority is a tool for allocating scarce power among endpoints when the chassis budget is constrained.
  4. PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status.

Explanation

Correct Answer

A:

Voice/data split depends on compatible VLAN membership, accepted 802.1Q tagging and endpoint network policy. The appropriate response is to configure an approved voice VLAN on the port while keeping the PC data VLAN constrained.

Incorrect Answers

B:

“Base LLDP discovery and LLDP-MED telephony advertisement are distinct capabilities and may require separate enablement” belongs to a separate IP Telephony Features issue: a powered endpoint detects a Junos switch but fails to negotiate voice prioritization because only ordinary LLDP is enabled. It does not explain the condition tested here.

C:

“PoE priority is a tool for allocating scarce power among endpoints when the chassis budget is constrained” belongs to a separate IP Telephony Features issue: a switch assigns equal PoE power priority to every port and disconnects an emergency phone before low-priority signage during a power shortage. It does not explain the condition tested here.

D:

“PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status” belongs to a separate IP Telephony Features issue: a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget. It does not explain the condition tested here.

Question 400

The team believes it has resolved this Junos issue: Members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication. Which observation best verifies the specific intended result?

  1. Two customers can use overlapping inner VLAN numbers without traffic mixing on the transport.
  2. Community members can communicate as intended while cross-community access remains blocked.
  3. The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion.
  4. The VLAN registration propagates to the intended downstream trunk and reaches its member ports.

Explanation

Correct Answer

B:

Community members can communicate as intended while cross-community access remains blocked. This checks the relevant result after map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated.

Incorrect Answers

A:

“Two customers can use overlapping inner VLAN numbers without traffic mixing on the transport” belongs to a separate Ethernet Switching and Spanning Tree issue: a service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff. It does not explain the condition tested here.

C:

“The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion” belongs to a separate Ethernet Switching and Spanning Tree issue: a large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits. It does not explain the condition tested here.

D:

“The VLAN registration propagates to the intended downstream trunk and reaches its member ports” belongs to a separate Ethernet Switching and Spanning Tree issue: a new switch automatically discovers VLAN registrations on one trunk, but an intermediate trunk lacks MVRP participation and blocks the VLAN. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.