100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 420
The team believes it has resolved this Junos issue: A BGP export configuration has a broad first match so a specific downstream deny never evaluates the target prefix. Which observation best verifies the specific intended result?
- The routing and forwarding tables show the intended multiple next hops only for qualifying routes.
- The desired received prefix is accepted and active while intentionally blocked prefixes stay rejected.
- The unauthorized route is rejected while intended export cases still match the proper terms.
- The chosen best path follows the documented attribute ordering rather than a single observed MED value.
Explanation
Correct Answer
C:The unauthorized route is rejected while intended export cases still match the proper terms. This checks the relevant result after put specific deny conditions before broad acceptance, and test the policy with representative routes.
Incorrect Answers
A:“The routing and forwarding tables show the intended multiple next hops only for qualifying routes” belongs to a separate Border Gateway Protocol (BGP) issue: equal candidate BGP routes are visible but no multipath forwarding entry is installed because eligibility or policy differs. It does not explain the condition tested here.
B:“The desired received prefix is accepted and active while intentionally blocked prefixes stay rejected” belongs to a separate Border Gateway Protocol (BGP) issue: a Junos route is hidden by import policy, but the team troubleshoots only local physical interfaces. It does not explain the condition tested here.
D:“The chosen best path follows the documented attribute ordering rather than a single observed MED value” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.
Question 421
To prevent recurrence of this precise networking failure, which practice should be adopted? A stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work.
- Test multicast source-path behavior under each failover case, not only unicast ping.
- Include source address changes in SSM subscription-management procedures.
- Maintain consistent RP mappings and failover tests across multicast routers.
- Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
Explanation
Correct Answer
A:Test multicast source-path behavior under each failover case, not only unicast ping. This guards against an RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic.
Incorrect Answers
B:“Include source address changes in SSM subscription-management procedures” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.
C:“Maintain consistent RP mappings and failover tests across multicast routers” belongs to a separate IP Multicast issue: an ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP. It does not explain the condition tested here.
D:“Document ASM/SSM selection and receiver-version prerequisites before multicast deployment” instead concerns another network scenario: A video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not address the requirement here.
Question 422
The team believes it has resolved this Junos issue: A full-mesh iBGP design is converted to route reflection but one peer is treated as an ordinary nonclient and route propagation fails. Which observation best verifies the specific intended result?
- After policy correction, chosen path and attribute ordering match documented routing intent.
- The IPv6 BGP route becomes eligible and forwards over an IPv6-resolvable next hop.
- The downstream client learns approved prefixes and cluster-loop checks remain operational.
- The selected BGP route reflects the intended higher LOCAL_PREF, and traceroute follows the approved exit.
Explanation
Correct Answer
C:The downstream client learns approved prefixes and cluster-loop checks remain operational. This checks the relevant result after inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration.
Incorrect Answers
A:“After policy correction, chosen path and attribute ordering match documented routing intent” belongs to a separate Border Gateway Protocol (BGP) issue: a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops. It does not explain the condition tested here.
B:“The IPv6 BGP route becomes eligible and forwards over an IPv6-resolvable next hop” belongs to a separate Border Gateway Protocol (BGP) issue: an IPv6 BGP peer receives a route with an unreachable IPv6 next hop despite an otherwise valid inet6 unicast advertisement. It does not explain the condition tested here.
D:“The selected BGP route reflects the intended higher LOCAL_PREF, and traceroute follows the approved exit” belongs to a separate Border Gateway Protocol (BGP) issue: an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path. It does not explain the condition tested here.
Question 423
A Junos enterprise team investigates this incident: An OSPF policy update redistributes a route without an appropriate external metric, shifting traffic to a slow backup. Which technical explanation most directly identifies the cause or design principle?
- OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior.
- OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication.
- OSPF database-description exchange can stall when adjacent interfaces disagree on MTU even though basic Hello connectivity exists.
- OSPF neighbors must agree on the area context to form adjacency on the common link.
Explanation
Correct Answer
A:OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior. The appropriate response is to review external metric type and value at the originator, then apply the documented traffic-engineering policy.
Incorrect Answers
B:“OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. It does not explain the condition tested here.
C:“OSPF database-description exchange can stall when adjacent interfaces disagree on MTU even though basic Hello connectivity exists” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs. It does not explain the condition tested here.
D:“OSPF neighbors must agree on the area context to form adjacency on the common link” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch uplink uses area 0.0.0.6 on one router and area 0.0.0.9 on its peer after a template copy. It does not explain the condition tested here.
Question 424
A network change is required for the following specific situation: A high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. Which corrective action is most appropriate?
- Check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power.
- Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
- Review LLDP and LLDP-MED operational status and enable supported MED policy for phone access.
- Update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port.
Explanation
Correct Answer
A:PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status. Verify this by checking that the phone receives stable negotiated power and the chassis stays within its supported budget under peak load.
Incorrect Answers
B:“Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media” belongs to a separate IP Telephony Features issue: a handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design. It does not explain the condition tested here.
C:“Review LLDP and LLDP-MED operational status and enable supported MED policy for phone access” belongs to a separate IP Telephony Features issue: a powered endpoint detects a Junos switch but fails to negotiate voice prioritization because only ordinary LLDP is enabled. It does not explain the condition tested here.
D:“Update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port” belongs to a separate IP Telephony Features issue: an IP phone uses the wrong location information for emergency response after a switch move. It does not explain the condition tested here.
Question 425
The team believes it has resolved this Junos issue: A boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. Which observation best verifies the specific intended result?
- Drop counters and queue utilization follow the intended curve through increasing load.
- Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.
- Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic.
- Controlled traffic probes pass valid bursts without permitting sustained rate violations.
Explanation
Correct Answer
C:Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic. This checks the relevant result after apply the appropriate interface rewrite rule and verify the contract-specific egress code points.
Incorrect Answers
A:“Drop counters and queue utilization follow the intended curve through increasing load” belongs to a separate Class of Service (CoS) issue: a RED drop profile is applied too aggressively and drops packets even under moderate load. It does not explain the condition tested here.
B:“Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses” belongs to a separate Class of Service (CoS) issue: a branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. It does not explain the condition tested here.
D:“Controlled traffic probes pass valid bursts without permitting sustained rate violations” belongs to a separate Class of Service (CoS) issue: a traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. It does not explain the condition tested here.
Question 426
To prevent recurrence of this precise networking failure, which practice should be adopted? A credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants.
- Separate EAP silence, reject and timeout counters in authentication operational monitoring.
- Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions.
- Document and test EAP timeout, explicit rejection and server-unavailable cases separately.
- Review MAC-device inventory, spoofing exposure and expiry before using MAC-based authorization.
Explanation
Correct Answer
C:Document and test EAP timeout, explicit rejection and server-unavailable cases separately. This guards against guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.
Incorrect Answers
A:“Separate EAP silence, reject and timeout counters in authentication operational monitoring” belongs to a separate Layer 2 Authentication and Access Control issue: a RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. It does not explain the condition tested here.
B:“Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. It does not explain the condition tested here.
D:“Review MAC-device inventory, spoofing exposure and expiry before using MAC-based authorization” belongs to a separate Layer 2 Authentication and Access Control issue: an industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service. It does not explain the condition tested here.
Question 427
Which suggested shortcut would be especially unsafe for this exact situation? A second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it.
- Configure two unrelated RP mappings and assume their failover and source state stay identical automatically.
- Measure receiver interest and multicast forwarding state before scaling new one-to-many services.
- Test multicast source-path behavior under each failover case, not only unicast ping.
- Keep an approved multicast group allocation and test boundary enforcement after routing changes.
Explanation
Correct Answer
A:The tempting alternative fails because anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture. The supported action is to verify anycast RP address and supported source synchronization method across the participating RP nodes.
Incorrect Answers
B:That prevention measure relates to a one-to-many lecture stream is configured as separate unicast connections and saturates a WAN link to a remote campus.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a redundant network changes the preferred route to the source while packets keep arriving on the other physical link.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured.; it is not the unsafe shortcut described here.
Question 428
A network change is required for the following specific situation: A transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated. Which corrective action is most appropriate?
- Verify endpoint reachability and configure appropriate multihop session parameters and security controls.
- Put specific deny conditions before broad acceptance, and test the policy with representative routes.
- Inspect received communities and export policy terms, then attach a tested community match and reject rule.
- Inspect active-route selection and the advertise-inactive configuration; keep it only if the external requirement justifies it.
Explanation
Correct Answer
A:Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints. Verify this by checking that a loopback-to-loopback BGP session becomes Established and exchanges only permitted NLRI.
Incorrect Answers
B:“Put specific deny conditions before broad acceptance, and test the policy with representative routes” belongs to a separate Border Gateway Protocol (BGP) issue: a route with a permissive policy term is accepted before a later deny term can block it. It does not explain the condition tested here.
C:“Inspect received communities and export policy terms, then attach a tested community match and reject rule” belongs to a separate Border Gateway Protocol (BGP) issue: a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. It does not explain the condition tested here.
D:“Inspect active-route selection and the advertise-inactive configuration; keep it only if the external requirement justifies it” belongs to a separate Border Gateway Protocol (BGP) issue: a BGP export policy advertises a prefix that exists only as an inactive local candidate, despite an expectation of default active-only behavior. It does not explain the condition tested here.
Question 429
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink.
- Map every packet to the lowest loss priority regardless of its out-of-profile status.
- Set the maximum drop probability at near-empty queue levels and expect no early loss.
- Measured guest ingress usage remains within policy and permitted business traffic is unaffected.
- Use an egress shaper at the wrong interface as a substitute for every ingress traffic-contract check.
- Apply a correctly scoped ingress policer with tested rate and burst values on the relevant flow.
Explanation
Correct Answers
C:Measured guest ingress usage remains within policy and permitted business traffic is unaffected. The specific steps required are to apply a correctly scoped ingress policer with tested rate and burst values on the relevant flow.
E:Apply a correctly scoped ingress policer with tested rate and burst values on the relevant flow. This addresses the dependency that a policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress.
Incorrect Answers
A:“Map every packet to the lowest loss priority regardless of its out-of-profile status” is an unsafe response to a different problem: packets with two different drop precedence values are treated as equally discardable during congestion. It is not a valid fix here.
B:“Set the maximum drop probability at near-empty queue levels and expect no early loss” is an unsafe response to a different problem: a RED drop profile is applied too aggressively and drops packets even under moderate load. It is not a valid fix here.
D:“Use an egress shaper at the wrong interface as a substitute for every ingress traffic-contract check” does not address a policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress.
Question 430
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A switch receives successful RADIUS Access-Accept but the user still lands in an unexpected VLAN because the dynamic assignment is not supported on that platform.
- Give MAC-authenticated devices the same unrestricted access as strongly authenticated employees.
- Check returned RADIUS attributes and supported platform software, then enforce a valid authorization assignment.
- Assume any RADIUS Access-Accept forces a requested dynamic VLAN on every Junos switch variant.
- The switch reports an authorized session with the intended VLAN and access policy.
- Add a static DNS record and assume it substitutes for captive-portal authentication and authorization.
Explanation
Correct Answers
B:Check returned RADIUS attributes and supported platform software, then enforce a valid authorization assignment. This addresses the dependency that authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary.
D:The switch reports an authorized session with the intended VLAN and access policy. The specific steps required are to check returned RADIUS attributes and supported platform software, then enforce a valid authorization assignment.
Incorrect Answers
A:“Give MAC-authenticated devices the same unrestricted access as strongly authenticated employees” is an unsafe response to a different problem: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It is not a valid fix here.
C:“Assume any RADIUS Access-Accept forces a requested dynamic VLAN on every Junos switch variant” does not address authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary.
E:“Add a static DNS record and assume it substitutes for captive-portal authentication and authorization” is an unsafe response to a different problem: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It is not a valid fix here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests