100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 440
Which suggested shortcut would be especially unsafe for this exact situation? A RED drop profile is applied too aggressively and drops packets even under moderate load.
- Audit DSCP preservation and remarking at untrusted edge boundaries.
- Document trusted-marking boundaries and test both matched and unmatched multifield traffic.
- Test both average-rate enforcement and microburst tolerance for new policer profiles.
- Set the maximum drop probability at near-empty queue levels and expect no early loss.
Explanation
Correct Answer
D:The tempting alternative fails because drop profiles and weighted random early detection influence probabilistic discard thresholds as queue fill rises. The supported action is to review configured drop probability versus fill level and align the profile with acceptable congestion targets.
Incorrect Answers
A:That prevention measure relates to a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice.; it is not the unsafe shortcut described here.
B:That prevention measure relates to an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight.; it is not the unsafe shortcut described here.
Question 441
The team believes it has resolved this Junos issue: A laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab. Which observation best verifies the specific intended result?
- Subscribed receivers get the stream without unnecessary flood to ports that did not join.
- PIM joins build the intended shared tree and the requested group begins forwarding to subscribers.
- The specified groups remain within the approved scope while unrelated enterprise multicast flows continue.
- Remote ASM receivers can discover the intended source and request multicast delivery through the proper tree.
Explanation
Correct Answer
C:The specified groups remain within the approved scope while unrelated enterprise multicast flows continue. This checks the relevant result after configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
Incorrect Answers
A:“Subscribed receivers get the stream without unnecessary flood to ports that did not join” belongs to a separate IP Multicast issue: an access VLAN floods every multicast packet because IGMP snooping state was lost during migration. It does not explain the condition tested here.
B:“PIM joins build the intended shared tree and the requested group begins forwarding to subscribers” belongs to a separate IP Multicast issue: an ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP. It does not explain the condition tested here.
D:“Remote ASM receivers can discover the intended source and request multicast delivery through the proper tree” belongs to a separate IP Multicast issue: a receiver domain requires discovery of sources known behind another RP, yet inter-RP source information exchange is absent. It does not explain the condition tested here.
Question 442
The team believes it has resolved this Junos issue: An ABR starts leaking a management static route into the enterprise IGP after a permissive export term was introduced. Which observation best verifies the specific intended result?
- An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0.
- The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests.
- Only authorized static prefixes appear as OSPF externals; management prefixes remain local.
- Hellos are observed in the routing adjacency and a Full neighbor appears on the intended port.
Explanation
Correct Answer
C:Only authorized static prefixes appear as OSPF externals; management prefixes remain local. This checks the relevant result after restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.
Incorrect Answers
A:“An OSPFv3 neighbor forms and approved IPv6 prefixes appear in inet6.0” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. It does not explain the condition tested here.
B:“The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.
D:“Hellos are observed in the routing adjacency and a Full neighbor appears on the intended port” belongs to a separate Interior Gateway Protocols (IGPs) issue: a distribution node learns connected subnets but never sends Hello packets on its OSPF transit port due to passive-interface policy. It does not explain the condition tested here.
Question 443
A Junos enterprise team investigates this incident: A campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route. Which technical explanation most directly identifies the cause or design principle?
- Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture.
- PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
- IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream.
- Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.
Explanation
Correct Answer
D:Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic. The appropriate response is to identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
Incorrect Answers
A:“Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture” belongs to a separate IP Multicast issue: a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it. It does not explain the condition tested here.
B:“PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service” belongs to a separate IP Multicast issue: a PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point. It does not explain the condition tested here.
C:“IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream” belongs to a separate IP Multicast issue: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It does not explain the condition tested here.
Question 444
Which suggested shortcut would be especially unsafe for this exact situation? An access VLAN floods every multicast packet because IGMP snooping state was lost during migration.
- Test multicast source-path behavior under each failover case, not only unicast ping.
- Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
- Measure receiver interest and multicast forwarding state before scaling new one-to-many services.
- Disable IGMP snooping everywhere and assume uncontrolled flooding is equivalent to correct membership delivery.
Explanation
Correct Answer
D:The tempting alternative fails because IGMP reports express receiver interest, and IGMP snooping uses that interest to constrain Layer 2 replication. The supported action is to inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
Incorrect Answers
A:That prevention measure relates to a redundant network changes the preferred route to the source while packets keep arriving on the other physical link.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone.; it is not the unsafe shortcut described here.
Question 445
To prevent recurrence of this precise networking failure, which practice should be adopted? A customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic.
- Audit DSCP preservation and remarking at untrusted edge boundaries.
- Test marking, PLP assignment and drop policy together rather than checking only DSCP fields.
- Validate classifier, scheduler map and interface association as a complete CoS chain.
- Review queue buffer tradeoffs and regression-test peak loads before tuning schedulers.
Explanation
Correct Answer
A:Audit DSCP preservation and remarking at untrusted edge boundaries. This guards against CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings.
Incorrect Answers
B:“Test marking, PLP assignment and drop policy together rather than checking only DSCP fields” belongs to a separate Class of Service (CoS) issue: packets with two different drop precedence values are treated as equally discardable during congestion. It does not explain the condition tested here.
C:“Validate classifier, scheduler map and interface association as a complete CoS chain” belongs to a separate Class of Service (CoS) issue: a low-latency queue is correctly classified but voice delays because its egress scheduler map is absent from the trunk. It does not explain the condition tested here.
D:“Review queue buffer tradeoffs and regression-test peak loads before tuning schedulers” belongs to a separate Class of Service (CoS) issue: a backup traffic queue consumes too much buffer and latency-sensitive applications starve during peak bursts. It does not explain the condition tested here.
Question 446
Which suggested shortcut would be especially unsafe for this exact situation? Two adjacent MSTP switches show different region digests after one has a different VLAN-to-instance map.
- Adjust Ethernet cable speed and expect different MSTP region digests to converge automatically.
- Check policy coverage and unintended-match cases before activating filter-based steering.
- Maintain representative match and nonmatch tests for filter-based VLAN policies.
- Include packet-capture verification of S-tag and C-tag transformation in provider handoffs.
Explanation
Correct Answer
A:The tempting alternative fails because MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map. The supported action is to compare complete region configuration on the peers and restore the approved shared MSTP region values.
Incorrect Answers
B:That prevention measure relates to an ingress classification filter for one terminal type inadvertently redirects other hosts using the same uplink.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a policy-based VLAN filter moves matching device traffic to a quarantine VLAN but a rule fails to match the intended MAC or packet fields.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a Q-in-Q service works across transport but the far-end access handoff presents unexpected double tags.; it is not the unsafe shortcut described here.
Question 447
A Junos enterprise team investigates this incident: A one-to-many lecture stream is configured as separate unicast connections and saturates a WAN link to a remote campus. Which technical explanation most directly identifies the cause or design principle?
- IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream.
- PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
- Reverse Path Forwarding checks whether multicast packets arrive on the interface selected toward the source or tree root.
- MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
Explanation
Correct Answer
A:IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream. The appropriate response is to design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths.
Incorrect Answers
B:“PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service” belongs to a separate IP Multicast issue: a PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point. It does not explain the condition tested here.
C:“Reverse Path Forwarding checks whether multicast packets arrive on the interface selected toward the source or tree root” belongs to a separate IP Multicast issue: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It does not explain the condition tested here.
D:“MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points” belongs to a separate IP Multicast issue: a receiver domain requires discovery of sources known behind another RP, yet inter-RP source information exchange is absent. It does not explain the condition tested here.
Question 448
To prevent recurrence of this precise networking failure, which practice should be adopted? A switch rollout splits a team that should communicate within one PVLAN community, while protecting it from another community.
- Test each critical VLAN's root bridge and forwarding path after VSTP updates.
- Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned.
- Document primary/secondary VLAN mappings and test permitted peer groups and isolation boundaries.
- Version-control MSTP name, revision and VLAN mapping as one change unit.
Explanation
Correct Answer
C:Document primary/secondary VLAN mappings and test permitted peer groups and isolation boundaries. This guards against a private VLAN community allows permitted communication within its community; isolated behavior is stricter.
Incorrect Answers
A:“Test each critical VLAN's root bridge and forwarding path after VSTP updates” belongs to a separate Ethernet Switching and Spanning Tree issue: a VSTP network intended to send voice and data VLANs over different active paths instead blocks both on the same uplink. It does not explain the condition tested here.
B:“Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It does not explain the condition tested here.
D:“Version-control MSTP name, revision and VLAN mapping as one change unit” belongs to a separate Ethernet Switching and Spanning Tree issue: two adjacent MSTP switches show different region digests after one has a different VLAN-to-instance map. It does not explain the condition tested here.
Question 449
Which suggested shortcut would be especially unsafe for this exact situation? A building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked.
- Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries.
- Test each critical VLAN's root bridge and forwarding path after VSTP updates.
- Disable private VLAN restrictions entirely as a shortcut to reach a single shared uplink service.
- Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
Explanation
Correct Answer
C:The tempting alternative fails because private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles. The supported action is to inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.
Incorrect Answers
A:That prevention measure relates to a service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a VSTP network intended to send voice and data VLANs over different active paths instead blocks both on the same uplink.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently.; it is not the unsafe shortcut described here.
Question 450
Select THREE complementary corrective, verification, or preventive controls for this scenario: A multicast source is active in a different PIM domain but the local ASM RP never learns the source mapping.
- Remote ASM receivers can discover the intended source and request multicast delivery through the proper tree.
- Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links.
- Review interdomain source-advertisement scope and MSDP peer availability for ASM deployments.
- Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages.
- Inspect MSDP peer state and source-active information, then configure the permitted peer relationships.
- Assume an ASM (*,G) join identifies and restricts a unique approved source by itself.
Explanation
Correct Answers
A:Confirmation: Inspect MSDP peer state and source-active information, then configure the permitted peer relationships.
C:Prevention of recurrence: MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
E:Correction: MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
Incorrect Answers
B:“Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links” is an unsafe response to a different problem: multicast packets arrive on the wrong uplink after unicast routing changes and are dropped by the campus core. It is not a valid fix here.
D:“Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages” does not address MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
F:“Assume an ASM (*,G) join identifies and restricts a unique approved source by itself” is an unsafe response to a different problem: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It is not a valid fix here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests