100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 450
Select THREE complementary corrective, verification, or preventive controls for this scenario: A multicast source is active in a different PIM domain but the local ASM RP never learns the source mapping.
- Remote ASM receivers can discover the intended source and request multicast delivery through the proper tree.
- Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links.
- Review interdomain source-advertisement scope and MSDP peer availability for ASM deployments.
- Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages.
- Inspect MSDP peer state and source-active information, then configure the permitted peer relationships.
- Assume an ASM (*,G) join identifies and restricts a unique approved source by itself.
Explanation
Correct Answers
A:Confirmation: Inspect MSDP peer state and source-active information, then configure the permitted peer relationships.
C:Prevention of recurrence: MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
E:Correction: MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
Incorrect Answers
B:“Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links” is an unsafe response to a different problem: multicast packets arrive on the wrong uplink after unicast routing changes and are dropped by the campus core. It is not a valid fix here.
D:“Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages” does not address MSDP is used in applicable ASM inter-RP designs to exchange active-source information between rendezvous points.
F:“Assume an ASM (*,G) join identifies and restricts a unique approved source by itself” is an unsafe response to a different problem: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It is not a valid fix here.
Question 451
A Junos enterprise team investigates this incident: A finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. Which technical explanation most directly identifies the cause or design principle?
- Packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior.
- Scheduler priority and bandwidth allocation affect queuing service but must balance fairness and starvation concerns.
- A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress.
- Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification.
Explanation
Correct Answer
B:Scheduler priority and bandwidth allocation affect queuing service but must balance fairness and starvation concerns. The appropriate response is to assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.
Incorrect Answers
A:“Packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior” belongs to a separate Class of Service (CoS) issue: packets with two different drop precedence values are treated as equally discardable during congestion. It does not explain the condition tested here.
C:“A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress” belongs to a separate Class of Service (CoS) issue: a branch wants to enforce a traffic contract on an incoming service flow yet applies policing to an unrelated egress path. It does not explain the condition tested here.
D:“Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification” belongs to a separate Class of Service (CoS) issue: an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It does not explain the condition tested here.
Question 452
Which suggested shortcut would be especially unsafe for this exact situation? Two OSPF routers on a shared transit segment report different Hello and dead intervals and never establish adjacency.
- Change only BGP keepalive values and assume OSPF timers automatically follow.
- Document expected external metrics and run primary/backup failover tests during policy changes.
- Record both LSDB presence and local RIB installation in OSPF troubleshooting runbooks.
- Keep IPv4 and IPv6 routing verification separate for dual-stack maintenance.
Explanation
Correct Answer
A:The tempting alternative fails because OSPF neighbors require compatible Hello and dead interval settings on the shared interface. The supported action is to compare OSPF interface timers and align the two peers to approved Hello and dead values.
Incorrect Answers
B:That prevention measure relates to a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health.; it is not the unsafe shortcut described here.
Question 453
To prevent recurrence of this precise networking failure, which practice should be adopted? A network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer.
- Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
- Include inet6-specific next-hop verification in dual-stack BGP peer checklists.
- Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes.
- Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
Explanation
Correct Answer
C:Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes. This guards against communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it.
Incorrect Answers
A:“Audit prefix and mask-length boundaries with positive and negative routing-policy tests” belongs to a separate Border Gateway Protocol (BGP) issue: an eBGP import policy unexpectedly accepts more-specific prefixes outside the approved customer allocation. It does not explain the condition tested here.
B:“Include inet6-specific next-hop verification in dual-stack BGP peer checklists” belongs to a separate Border Gateway Protocol (BGP) issue: an IPv6 transit prefix is hidden because its next-hop address is absent from the correct IPv6 routing table. It does not explain the condition tested here.
D:“Include next-hop reachability tests in iBGP and route-reflector deployment acceptance” belongs to a separate Border Gateway Protocol (BGP) issue: a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. It does not explain the condition tested here.
Question 454
Which suggested shortcut would be especially unsafe for this exact situation? A remote prefix appears in incoming BGP updates yet never becomes active after a new route policy was applied.
- Review policy ordering with negative tests and explicit default actions on every change.
- Keep restarting the established BGP session without evaluating import-policy filtering.
- Validate every route-reflector client and failover path in topology inventory before conversion.
- Include inet6-specific next-hop verification in dual-stack BGP peer checklists.
Explanation
Correct Answer
B:The tempting alternative fails because a BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session. The supported action is to inspect hidden-route reason, incoming attributes and import-policy decisions, then correct the authorized match.
Incorrect Answers
A:That prevention measure relates to a BGP export configuration has a broad first match so a specific downstream deny never evaluates the target prefix.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an IPv6 transit prefix is hidden because its next-hop address is absent from the correct IPv6 routing table.; it is not the unsafe shortcut described here.
Question 455
A network change is required for the following specific situation: After a RADIUS outage, the access switch opens ports broadly instead of applying the approved restricted server-fail VLAN. Which corrective action is most appropriate?
- Inspect packet exchange and classify the endpoint before selecting a supported fallback method.
- Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.
- Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
- Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
Explanation
Correct Answer
D:Server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access. Verify this by checking that during a simulated RADIUS outage, endpoints receive only the approved degraded-connectivity policy.
Incorrect Answers
A:“Inspect packet exchange and classify the endpoint before selecting a supported fallback method” belongs to a separate Layer 2 Authentication and Access Control issue: a RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. It does not explain the condition tested here.
B:“Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. It does not explain the condition tested here.
C:“Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration” belongs to a separate Layer 2 Authentication and Access Control issue: a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend. It does not explain the condition tested here.
Question 456
To prevent recurrence of this precise networking failure, which practice should be adopted? A traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight.
- Test marking, PLP assignment and drop policy together rather than checking only DSCP fields.
- Keep queue drop-profile acceptance tests and monitor production congestion before broad rollout.
- Test both average-rate enforcement and microburst tolerance for new policer profiles.
- Test ingress classification separately from egress rewrite at every trust boundary.
Explanation
Correct Answer
C:Test both average-rate enforcement and microburst tolerance for new policer profiles. This guards against policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.
Incorrect Answers
A:“Test marking, PLP assignment and drop policy together rather than checking only DSCP fields” belongs to a separate Class of Service (CoS) issue: packets with two different drop precedence values are treated as equally discardable during congestion. It does not explain the condition tested here.
B:“Keep queue drop-profile acceptance tests and monitor production congestion before broad rollout” belongs to a separate Class of Service (CoS) issue: a RED drop profile is applied too aggressively and drops packets even under moderate load. It does not explain the condition tested here.
D:“Test ingress classification separately from egress rewrite at every trust boundary” belongs to a separate Class of Service (CoS) issue: a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. It does not explain the condition tested here.
Question 457
A network change is required for the following specific situation: A desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. Which corrective action is most appropriate?
- Configure an approved voice VLAN on the port while keeping the PC data VLAN constrained.
- Inspect PoE class, per-port priority and available chassis budget, and move to a supported powered port if needed.
- Enable supported LLDP-MED network policy on the phone-facing port and verify advertisements and phone settings.
- Update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port.
Explanation
Correct Answer
A:Voice/data split depends on compatible VLAN membership, accepted 802.1Q tagging and endpoint network policy. Verify this by checking that the phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN.
Incorrect Answers
B:“Inspect PoE class, per-port priority and available chassis budget, and move to a supported powered port if needed” belongs to a separate IP Telephony Features issue: a phone's LLDP-negotiated power demand exceeds its access port's allocated PoE limit and it repeatedly restarts. It does not explain the condition tested here.
C:“Enable supported LLDP-MED network policy on the phone-facing port and verify advertisements and phone settings” belongs to a separate IP Telephony Features issue: a newly deployed IP phone joins the data network because the switch does not advertise the intended voice VLAN through LLDP-MED. It does not explain the condition tested here.
D:“Update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port” belongs to a separate IP Telephony Features issue: an IP phone uses the wrong location information for emergency response after a switch move. It does not explain the condition tested here.
Question 458
A network change is required for the following specific situation: A non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. Which corrective action is most appropriate?
- Configure supported MAC RADIUS under least-privilege policy and register the device MAC with the approved service.
- Inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior.
- Check returned RADIUS attributes and supported platform software, then enforce a valid authorization assignment.
- Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
Explanation
Correct Answer
A:MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X. Verify this by checking that the registered device is authorized with limited access; an unknown MAC remains blocked.
Incorrect Answers
B:“Inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior” belongs to a separate Layer 2 Authentication and Access Control issue: two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result. It does not explain the condition tested here.
C:“Check returned RADIUS attributes and supported platform software, then enforce a valid authorization assignment” belongs to a separate Layer 2 Authentication and Access Control issue: an EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization. It does not explain the condition tested here.
D:“Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform” belongs to a separate Layer 2 Authentication and Access Control issue: an enterprise fallback design accidentally places unauthenticated users into the production network when all RADIUS servers fail. It does not explain the condition tested here.
Question 459
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A vendor handset discovers its neighbor using basic LLDP but does not learn the configured network policy for voice tagging.
- Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power.
- The handset learns the authorized voice VLAN and traffic is tagged and prioritized according to design.
- Enable supported LLDP-MED network policy on the phone-facing port and verify advertisements and phone settings.
- Put the phone and PC on one unrestricted VLAN to avoid checking voice VLAN tagging.
- Assume generic LLDP chassis identification alone announces the correct voice VLAN and QoS settings.
Explanation
Correct Answers
B:The handset learns the authorized voice VLAN and traffic is tagged and prioritized according to design. The specific steps required are to enable supported LLDP-MED network policy on the phone-facing port and verify advertisements and phone settings.
C:Enable supported LLDP-MED network policy on the phone-facing port and verify advertisements and phone settings. This addresses the dependency that LLDP-MED extends device discovery with telephony-related network-policy TLVs that need compatible endpoint behavior.
Incorrect Answers
A:“Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power” is an unsafe response to a different problem: a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. It is not a valid fix here.
D:“Put the phone and PC on one unrestricted VLAN to avoid checking voice VLAN tagging” is an unsafe response to a different problem: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It is not a valid fix here.
E:“Assume generic LLDP chassis identification alone announces the correct voice VLAN and QoS settings” does not address LLDP-MED extends device discovery with telephony-related network-policy TLVs that need compatible endpoint behavior.
Question 460
A Junos enterprise team investigates this incident: The local AS appears in a received external BGP AS_PATH and the route is rejected despite valid prefix reachability. Which technical explanation most directly identifies the cause or design principle?
- The default BGP AS-path loop check rejects routes containing the local autonomous system to prevent loops.
- BGP address-family negotiation controls which IPv4 or IPv6 NLRI can be exchanged independently of session state.
- BGP route selection first requires the BGP next hop to resolve through the appropriate routing table.
- For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner.
Explanation
Correct Answer
A:The default BGP AS-path loop check rejects routes containing the local autonomous system to prevent loops. The appropriate response is to check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks.
Incorrect Answers
B:“BGP address-family negotiation controls which IPv4 or IPv6 NLRI can be exchanged independently of session state” belongs to a separate Border Gateway Protocol (BGP) issue: a campus router's BGP IPv6 session is Established yet peers advertise only inet unicast family routes. It does not explain the condition tested here.
C:“BGP route selection first requires the BGP next hop to resolve through the appropriate routing table” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. It does not explain the condition tested here.
D:“For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner” belongs to a separate Border Gateway Protocol (BGP) issue: a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests