Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 54

Question 530

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it.

  1. Assume an ASM (*,G) join identifies and restricts a unique approved source by itself.
  2. Verify anycast RP address and supported source synchronization method across the participating RP nodes.
  3. Treat SSM group membership as source-agnostic and subscribe to the group without source information.
  4. A failure of one RP does not strand subscribers and remaining RPs maintain correct multicast source awareness.
  5. Configure two unrelated RP mappings and assume their failover and source state stay identical automatically.

Explanation

Correct Answers

B:

Verify anycast RP address and supported source synchronization method across the participating RP nodes. This addresses the dependency that anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture.

D:

A failure of one RP does not strand subscribers and remaining RPs maintain correct multicast source awareness. The specific steps required are to verify anycast RP address and supported source synchronization method across the participating RP nodes.

Incorrect Answers

A:

“Assume an ASM (*,G) join identifies and restricts a unique approved source by itself” is an unsafe response to a different problem: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It is not a valid fix here.

C:

“Treat SSM group membership as source-agnostic and subscribe to the group without source information” is an unsafe response to a different problem: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It is not a valid fix here.

E:

“Configure two unrelated RP mappings and assume their failover and source state stay identical automatically” does not address anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture.

Question 531

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A campus changes a telephone port but LLDP-MED location data remains mapped to an old floor.

  1. Assume a green Ethernet link light proves an endpoint has its required operating power.
  2. Update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port.
  3. The phone or location service reports the correct emergency location for the new access port.
  4. Allocate identical priority to all PoE consumers and assume emergency devices receive preferential power.
  5. Treat the old physical room value as correct because IP addressing did not change.

Explanation

Correct Answers

B:

Update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port. This addresses the dependency that LLDP-MED location metadata can support telephony location services and must match actual switch-port placement.

C:

The phone or location service reports the correct emergency location for the new access port. The specific steps required are to update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port.

Incorrect Answers

A:

“Assume a green Ethernet link light proves an endpoint has its required operating power” is an unsafe response to a different problem: a phone's LLDP-negotiated power demand exceeds its access port's allocated PoE limit and it repeatedly restarts. It is not a valid fix here.

D:

“Allocate identical priority to all PoE consumers and assume emergency devices receive preferential power” is an unsafe response to a different problem: a switch assigns equal PoE power priority to every port and disconnects an emergency phone before low-priority signage during a power shortage. It is not a valid fix here.

E:

“Treat the old physical room value as correct because IP addressing did not change” does not address LLDP-MED location metadata can support telephony location services and must match actual switch-port placement.

Question 532

The team believes it has resolved this Junos issue: Two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result. Which observation best verifies the specific intended result?

  1. The switch reports an authorized session with the intended VLAN and access policy.
  2. Authenticated corporate devices use strong EAP policies while designated legacy endpoints use restricted fallback.
  3. The known device reaches only permitted destinations and cannot reach employee or management resources.
  4. A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state.

Explanation

Correct Answer

B:

Authenticated corporate devices use strong EAP policies while designated legacy endpoints use restricted fallback. This checks the relevant result after inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior.

Incorrect Answers

A:

“The switch reports an authorized session with the intended VLAN and access policy” belongs to a separate Layer 2 Authentication and Access Control issue: an EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization. It does not explain the condition tested here.

C:

“The known device reaches only permitted destinations and cannot reach employee or management resources” belongs to a separate Layer 2 Authentication and Access Control issue: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It does not explain the condition tested here.

D:

“A known-good supplicant completes EAP/RADIUS authentication and the port reaches its intended authorized state” belongs to a separate Layer 2 Authentication and Access Control issue: a corporate laptop presents valid 802.1X credentials but stays unauthorized because the switch is using the wrong RADIUS server profile. It does not explain the condition tested here.

Question 533

Which suggested shortcut would be especially unsafe for this exact situation? A bridge domain has valid unicast Type 2 entries yet remote VTEPs do not discover a new participating segment for BUM forwarding.

  1. Maintain a central VNI registry and test cross-tenant isolation on each leaf rollout.
  2. Treat a single learned MAC/IP Type 2 route as guaranteed proof of correct BUM participation for every VTEP.
  3. Include underlay loopback reachability and MTU checks in VXLAN overlay deployment QA.
  4. Audit ESI consistency and platform-supported multihoming mode across paired leafs.

Explanation

Correct Answer

B:

The tempting alternative fails because EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set. The supported action is to inspect Type 3 routes and VNI import/export membership; repair the intended inclusive-multicast advertisement.

Incorrect Answers

A:

That prevention measure relates to a fabric uses conflicting VLAN-to-VNI mappings on two leaf switches, bridging different tenant segments together.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a new leaf imports VNI reachability but packets disappear because its VXLAN tunnel endpoint IP is unresolved.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior.; it is not the unsafe shortcut described here.

Question 534

Which suggested shortcut would be especially unsafe for this exact situation? Two newly deployed distribution switches report identical OSPF router IDs, causing inconsistent LSAs in the area.

  1. Raise interface OSPF costs without resolving the duplicated router IDs.
  2. Verify both protocol RIB candidates and active next-hop selection in dual-stack change tests.
  3. Use named prefix lists and regression tests for approved and denied redistribution cases.
  4. Validate active logical-interface mappings and IPv6 adjacency as part of change acceptance.

Explanation

Correct Answer

A:

The tempting alternative fails because OSPF identifies routers by unique router ID; collisions can destabilize LSDB and adjacency behavior. The supported action is to assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence.

Incorrect Answers

B:

That prevention measure relates to a team wrongly concludes OSPFv3 failed when inet6.0 shows a static route active and the OSPFv3 candidate inactive.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear.; it is not the unsafe shortcut described here.

Question 535

The team believes it has resolved this Junos issue: A replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring. Which observation best verifies the specific intended result?

  1. The backbone receives the intended aggregate and routers can reach all included component subnets.
  2. The remote inet6.0 table learns the intended loopback and reachability testing succeeds.
  3. Only authorized static prefixes appear as OSPF externals; management prefixes remain local.
  4. OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements.

Explanation

Correct Answer

B:

The remote inet6.0 table learns the intended loopback and reachability testing succeeds. This checks the relevant result after inspect IPv6 interface addresses and OSPFv3 interface participation, then add the intended loopback advertisement within policy.

Incorrect Answers

A:

“The backbone receives the intended aggregate and routers can reach all included component subnets” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR stops advertising a branch prefix into the backbone after an OSPF area-range summary is configured incorrectly. It does not explain the condition tested here.

C:

“Only authorized static prefixes appear as OSPF externals; management prefixes remain local” belongs to a separate Interior Gateway Protocols (IGPs) issue: a redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local. It does not explain the condition tested here.

D:

“OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus OSPF interface is accidentally placed in area 0 while its neighbor advertises a nonbackbone area, preventing a Full adjacency. It does not explain the condition tested here.

Question 536

A network change is required for the following specific situation: A private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. Which corrective action is most appropriate?

  1. Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement.
  2. Compare complete region configuration on the peers and restore the approved shared MSTP region values.
  3. Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.
  4. Configure supported L2PT for the required control protocols and verify provider-edge handling.

Explanation

Correct Answer

D:

Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough. Verify this by checking that the customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology.

Incorrect Answers

A:

“Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.

B:

“Compare complete region configuration on the peers and restore the approved shared MSTP region values” belongs to a separate Ethernet Switching and Spanning Tree issue: two adjacent MSTP switches show different region digests after one has a different VLAN-to-instance map. It does not explain the condition tested here.

C:

“Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them. It does not explain the condition tested here.

Question 537

A network change is required for the following specific situation: A carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path. Which corrective action is most appropriate?

  1. Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence.
  2. Check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks.
  3. Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration.
  4. Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.

Explanation

Correct Answer

B:

The default BGP AS-path loop check rejects routes containing the local autonomous system to prevent loops. Verify this by checking that the route is accepted only after the AS-path loop is removed, with stable forwarding.

Incorrect Answers

A:

“Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.

C:

“Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration” belongs to a separate Border Gateway Protocol (BGP) issue: a full-mesh iBGP design is converted to route reflection but one peer is treated as an ordinary nonclient and route propagation fails. It does not explain the condition tested here.

D:

“Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail” belongs to a separate Border Gateway Protocol (BGP) issue: a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. It does not explain the condition tested here.

Question 538

To prevent recurrence of this precise networking failure, which practice should be adopted? A MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale.

  1. Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions.
  2. Track hardware, software edition and port family when standardizing access policies.
  3. Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance.
  4. Include downstream device count and authentication method in desk-port templates.

Explanation

Correct Answer

A:

Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions. This guards against MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication.

Incorrect Answers

B:

“Track hardware, software edition and port family when standardizing access policies” belongs to a separate Layer 2 Authentication and Access Control issue: an access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces. It does not explain the condition tested here.

C:

“Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.

D:

“Include downstream device count and authentication method in desk-port templates” belongs to a separate Layer 2 Authentication and Access Control issue: an access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It does not explain the condition tested here.

Question 539

A network change is required for the following specific situation: An OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. Which corrective action is most appropriate?

  1. Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.
  2. Verify the aggregate range, component prefixes and ABR advertisements, then correct the summary policy to the approved address plan.
  3. Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
  4. Assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence.

Explanation

Correct Answer

C:

IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges. Verify this by checking that the affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests.

Incorrect Answers

A:

“Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs” belongs to a separate Interior Gateway Protocols (IGPs) issue: a redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local. It does not explain the condition tested here.

B:

“Verify the aggregate range, component prefixes and ABR advertisements, then correct the summary policy to the approved address plan” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR stops advertising a branch prefix into the backbone after an OSPF area-range summary is configured incorrectly. It does not explain the condition tested here.

D:

“Assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence” belongs to a separate Interior Gateway Protocols (IGPs) issue: a router's OSPF neighbor restarts repeatedly because duplicate router IDs were assigned to different routing nodes. It does not explain the condition tested here.

Question 540

The team believes it has resolved this Junos issue: A video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. Which observation best verifies the specific intended result?

  1. Subscribed receivers get the stream without unnecessary flood to ports that did not join.
  2. PIM joins build the intended shared tree and the requested group begins forwarding to subscribers.
  3. Restricted groups are stopped at the boundary while approved collaboration streams still reach subscribers.
  4. Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow.

Explanation

Correct Answer

D:

Receivers subscribed to the intended (S,G) get traffic while nonselected sources cannot join that flow. This checks the relevant result after select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.

Incorrect Answers

A:

“Subscribed receivers get the stream without unnecessary flood to ports that did not join” belongs to a separate IP Multicast issue: an access VLAN floods every multicast packet because IGMP snooping state was lost during migration. It does not explain the condition tested here.

B:

“PIM joins build the intended shared tree and the requested group begins forwarding to subscribers” belongs to a separate IP Multicast issue: an ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP. It does not explain the condition tested here.

C:

“Restricted groups are stopped at the boundary while approved collaboration streams still reach subscribers” belongs to a separate IP Multicast issue: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.