Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 59

Question 580

A Junos enterprise team investigates this incident: An edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. Which technical explanation most directly identifies the cause or design principle?

  1. Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture.
  2. Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.
  3. Policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked.
  4. ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender.

Explanation

Correct Answer

C:

Policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked. The appropriate response is to refine the relevant multicast policy ranges and inspect forwarding for both permitted and denied groups.

Incorrect Answers

A:

“Anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture” belongs to a separate IP Multicast issue: a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it. It does not explain the condition tested here.

B:

“Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic” belongs to a separate IP Multicast issue: a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. It does not explain the condition tested here.

D:

“ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender” belongs to a separate IP Multicast issue: a campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests. It does not explain the condition tested here.

Question 581

Which suggested shortcut would be especially unsafe for this exact situation? A streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription.

  1. Test RP failover and synchronization behavior before expanding Anycast RP.
  2. Run both allow and deny group tests against multicast policy whenever prefixes are revised.
  3. Treat SSM group membership as source-agnostic and subscribe to the group without source information.
  4. Test multicast source-path behavior under each failover case, not only unicast ping.

Explanation

Correct Answer

C:

The tempting alternative fails because ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender. The supported action is to update receiver memberships to use the approved source and group, and validate end-to-end (S,G) trees.

Incorrect Answers

A:

That prevention measure relates to a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work.; it is not the unsafe shortcut described here.

Question 582

A Junos enterprise team investigates this incident: Multicast packets arrive on the wrong uplink after unicast routing changes and are dropped by the campus core. Which technical explanation most directly identifies the cause or design principle?

  1. IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream.
  2. PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.
  3. Policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked.
  4. Reverse Path Forwarding checks whether multicast packets arrive on the interface selected toward the source or tree root.

Explanation

Correct Answer

D:

Reverse Path Forwarding checks whether multicast packets arrive on the interface selected toward the source or tree root. The appropriate response is to inspect multicast RPF state and the routing table used for source resolution, then correct the underlay or allowed RPF selection.

Incorrect Answers

A:

“IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream” belongs to a separate IP Multicast issue: a one-to-many lecture stream is configured as separate unicast connections and saturates a WAN link to a remote campus. It does not explain the condition tested here.

B:

“PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree” belongs to a separate IP Multicast issue: a PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface. It does not explain the condition tested here.

C:

“Policy selectors must match the intended multicast group and source ranges so unrelated services are not blocked or leaked” belongs to a separate IP Multicast issue: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It does not explain the condition tested here.

Question 583

To prevent recurrence of this precise networking failure, which practice should be adopted? A BGP export policy advertises a prefix that exists only as an inactive local candidate, despite an expectation of default active-only behavior.

  1. Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
  2. Maintain expected BGP attribute decisions for every primary/secondary transit policy.
  3. Track every BGP advertise-inactive exception and test cross-protocol route selection.
  4. Monitor AS-path anomalies and validate inter-AS topology changes before enabling export.

Explanation

Correct Answer

C:

Track every BGP advertise-inactive exception and test cross-protocol route selection. This guards against Junos normally exports active routes; advertise-inactive can expose a best BGP candidate that lost to another protocol.

Incorrect Answers

A:

“Include next-hop reachability tests in iBGP and route-reflector deployment acceptance” belongs to a separate Border Gateway Protocol (BGP) issue: a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. It does not explain the condition tested here.

B:

“Maintain expected BGP attribute decisions for every primary/secondary transit policy” belongs to a separate Border Gateway Protocol (BGP) issue: a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops. It does not explain the condition tested here.

D:

“Monitor AS-path anomalies and validate inter-AS topology changes before enabling export” belongs to a separate Border Gateway Protocol (BGP) issue: the local AS appears in a received external BGP AS_PATH and the route is rejected despite valid prefix reachability. It does not explain the condition tested here.

Question 584

Which suggested shortcut would be especially unsafe for this exact situation? A stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work.

  1. Include source address changes in SSM subscription-management procedures.
  2. Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
  3. Require multicast forwarding to follow the receiver's shortest downstream path with no regard to source RPF.
  4. Test RP failover and synchronization behavior before expanding Anycast RP.

Explanation

Correct Answer

C:

The tempting alternative fails because an RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic. The supported action is to compare source-route preference with actual multicast ingress and restore a consistent authorized upstream path.

Incorrect Answers

A:

That prevention measure relates to a campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it.; it is not the unsafe shortcut described here.

Question 585

A network change is required for the following specific situation: An OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated. Which corrective action is most appropriate?

  1. Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
  2. Verify the aggregate range, component prefixes and ABR advertisements, then correct the summary policy to the approved address plan.
  3. Compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints.
  4. Inspect the active local default and export term conditions; match only the authorized static default source.

Explanation

Correct Answer

D:

Routing-policy match criteria must align with the source route type and the intended OSPF export behavior. Verify this by checking that a designated external default appears at downstream routers without leaking unrelated static prefixes.

Incorrect Answers

A:

“Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.

B:

“Verify the aggregate range, component prefixes and ABR advertisements, then correct the summary policy to the approved address plan” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus summarization change hides a needed subnet because the configured address range omits it. It does not explain the condition tested here.

C:

“Compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs. It does not explain the condition tested here.

Question 586

A Junos enterprise team investigates this incident: A shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. Which technical explanation most directly identifies the cause or design principle?

  1. Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink.
  2. Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
  3. MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.
  4. MVRP distributes VLAN registration information across participating links; a gap can stop propagation.

Explanation

Correct Answer

A:

Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink. The appropriate response is to inspect primary and secondary private VLAN roles and port membership; restore approved isolated/community mappings.

Incorrect Answers

B:

“Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns” belongs to a separate Ethernet Switching and Spanning Tree issue: a network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN. It does not explain the condition tested here.

C:

“MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control” belongs to a separate Ethernet Switching and Spanning Tree issue: a large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits. It does not explain the condition tested here.

D:

“MVRP distributes VLAN registration information across participating links; a gap can stop propagation” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. It does not explain the condition tested here.

Question 587

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local.

  1. Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.
  2. Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy.
  3. Only authorized static prefixes appear as OSPF externals; management prefixes remain local.
  4. Set a blanket export accept action and rely on other routers to ignore sensitive prefixes.
  5. Change only BGP keepalive values and assume OSPF timers automatically follow.

Explanation

Correct Answers

A:

Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs. This addresses the dependency that unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability.

C:

Only authorized static prefixes appear as OSPF externals; management prefixes remain local. The specific steps required are to restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.

Incorrect Answers

B:

“Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy” is an unsafe response to a different problem: an IPv6 branch outage is misdiagnosed using only IPv4 pings, despite OSPFv3 neighbors using IPv6 link-local messaging. It is not a valid fix here.

D:

“Set a blanket export accept action and rely on other routers to ignore sensitive prefixes” does not address unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability.

E:

“Change only BGP keepalive values and assume OSPF timers automatically follow” is an unsafe response to a different problem: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It is not a valid fix here.

Question 588

To prevent recurrence of this precise networking failure, which practice should be adopted? An IP phone uses the wrong location information for emergency response after a switch move.

  1. Test both tagged phone frames and untagged PC frames during phone-port commissioning.
  2. Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
  3. Synchronize switchport moves with maintained emergency location records.
  4. Validate PD power profiles and test peak draw rather than idle boot alone.

Explanation

Correct Answer

C:

Synchronize switchport moves with maintained emergency location records. This guards against LLDP-MED location metadata can support telephony location services and must match actual switch-port placement.

Incorrect Answers

A:

“Test both tagged phone frames and untagged PC frames during phone-port commissioning” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.

B:

“Capacity-plan PoE power classes and reserved headroom before connecting new powered devices” belongs to a separate IP Telephony Features issue: a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget. It does not explain the condition tested here.

D:

“Validate PD power profiles and test peak draw rather than idle boot alone” belongs to a separate IP Telephony Features issue: an emergency intercom can establish Ethernet link but loses power during activity because its PD class is not supported by that port. It does not explain the condition tested here.

Question 589

To prevent recurrence of this precise networking failure, which practice should be adopted? A receiver port stops getting multicast because IGMP membership was not processed by the access switch after an interface move.

  1. Monitor IGMP membership churn and snooping state when moving clients between VLANs.
  2. Check multicast and unicast topology alignment whenever routing paths or metrics change.
  3. Include source address changes in SSM subscription-management procedures.
  4. Keep an approved multicast group allocation and test boundary enforcement after routing changes.

Explanation

Correct Answer

A:

Monitor IGMP membership churn and snooping state when moving clients between VLANs. This guards against IGMP reports express receiver interest, and IGMP snooping uses that interest to constrain Layer 2 replication.

Incorrect Answers

B:

“Check multicast and unicast topology alignment whenever routing paths or metrics change” belongs to a separate IP Multicast issue: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It does not explain the condition tested here.

C:

“Include source address changes in SSM subscription-management procedures” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.

D:

“Keep an approved multicast group allocation and test boundary enforcement after routing changes” belongs to a separate IP Multicast issue: a laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab. It does not explain the condition tested here.

Question 590

A network change is required for the following specific situation: An aggregation broadcast VLAN has a DR/BDR placement that conflicts with the approved design after a maintenance reboot. Which corrective action is most appropriate?

  1. Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
  2. Inspect network type, interface priority and existing election state, then plan a controlled DR/BDR change.
  3. Inspect IPv6 interface addresses and OSPFv3 interface participation, then add the intended loopback advertisement within policy.
  4. Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.

Explanation

Correct Answer

B:

DR/BDR elections on OSPF broadcast networks affect LSA exchange and can be influenced by priority. Verify this by checking that neighbor states and DR/BDR assignments match the approved design following a managed election.

Incorrect Answers

A:

“Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.

C:

“Inspect IPv6 interface addresses and OSPFv3 interface participation, then add the intended loopback advertisement within policy” belongs to a separate Interior Gateway Protocols (IGPs) issue: a replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring. It does not explain the condition tested here.

D:

“Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core node shows a missing route while remote LSDBs include the corresponding external LSA after a local policy change. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.