100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 610
The team believes it has resolved this Junos issue: A campus uses a separate inet.2 multicast RPF table and investigators inspect only inet.0, overlooking a stale source route. Which observation best verifies the specific intended result?
- The required PIM neighbors appear and downstream join state tracks active interested receivers.
- Only the specified source delivers data to receivers of the chosen SSM group.
- The selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow.
- Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream.
Explanation
Correct Answer
C:The selected upstream RPF neighbor and packet arrival interface agree, restoring intended multicast flow. This checks the relevant result after identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
Incorrect Answers
A:“The required PIM neighbors appear and downstream join state tracks active interested receivers” belongs to a separate IP Multicast issue: a PIM sparse-mode segment cannot maintain neighbor state because PIM is configured on the wrong routed interface. It does not explain the condition tested here.
B:“Only the specified source delivers data to receivers of the chosen SSM group” belongs to a separate IP Multicast issue: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It does not explain the condition tested here.
D:“Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream” belongs to a separate IP Multicast issue: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It does not explain the condition tested here.
Question 611
A Junos enterprise team investigates this incident: An IP phone uses the wrong location information for emergency response after a switch move. Which technical explanation most directly identifies the cause or design principle?
- Physical PoE delivery and negotiated device power requirements must match switch and endpoint capabilities.
- PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status.
- Voice/data split depends on compatible VLAN membership, accepted 802.1Q tagging and endpoint network policy.
- LLDP-MED location metadata can support telephony location services and must match actual switch-port placement.
Explanation
Correct Answer
D:LLDP-MED location metadata can support telephony location services and must match actual switch-port placement. The appropriate response is to update the approved location mapping and confirm transmitted LLDP-MED location information on the affected port.
Incorrect Answers
A:“Physical PoE delivery and negotiated device power requirements must match switch and endpoint capabilities” belongs to a separate IP Telephony Features issue: a phone's LLDP-negotiated power demand exceeds its access port's allocated PoE limit and it repeatedly restarts. It does not explain the condition tested here.
B:“PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status” belongs to a separate IP Telephony Features issue: a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. It does not explain the condition tested here.
C:“Voice/data split depends on compatible VLAN membership, accepted 802.1Q tagging and endpoint network policy” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.
Question 612
A Junos enterprise team investigates this incident: An access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. Which technical explanation most directly identifies the cause or design principle?
- 802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized.
- 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed.
- MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision.
- Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies.
Explanation
Correct Answer
A:802.1X host-mode selection affects whether multiple downstream devices can be independently authenticated and authorized. The appropriate response is to select a supported multi-supplicant or appropriate phone/PC access mode and test per-device policies.
Incorrect Answers
B:“802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed” belongs to a separate Layer 2 Authentication and Access Control issue: an engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them. It does not explain the condition tested here.
C:“MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision” belongs to a separate Layer 2 Authentication and Access Control issue: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It does not explain the condition tested here.
D:“Guest, server-reject and server-fail outcomes represent different causes and require distinct supported policies” belongs to a separate Layer 2 Authentication and Access Control issue: a switch assigns a misconfigured laptop with incorrect EAP credentials to a VLAN intended only for devices that never attempt 802.1X. It does not explain the condition tested here.
Question 613
A network change is required for the following specific situation: A Junos route is hidden by import policy, but the team troubleshoots only local physical interfaces. Which corrective action is most appropriate?
- Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence.
- Inspect per-route local preferences and import policy; set the intended exit's LOCAL_PREF consistently.
- Verify endpoint reachability and configure appropriate multihop session parameters and security controls.
- Inspect hidden-route reason, incoming attributes and import-policy decisions, then correct the authorized match.
Explanation
Correct Answer
D:A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session. Verify this by checking that the desired received prefix is accepted and active while intentionally blocked prefixes stay rejected.
Incorrect Answers
A:“Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence” belongs to a separate Border Gateway Protocol (BGP) issue: an engineer incorrectly assumes a lower MED overrides a larger LOCAL_PREF, when both transit candidates are eligible. It does not explain the condition tested here.
B:“Inspect per-route local preferences and import policy; set the intended exit's LOCAL_PREF consistently” belongs to a separate Border Gateway Protocol (BGP) issue: two iBGP exits offer equal reachable routes but the one with higher LOCAL_PREF is not the egress an operator expected. It does not explain the condition tested here.
C:“Verify endpoint reachability and configure appropriate multihop session parameters and security controls” belongs to a separate Border Gateway Protocol (BGP) issue: a transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated. It does not explain the condition tested here.
Question 614
A Junos enterprise team investigates this incident: A route-reflector client receives an external destination but lacks the underlay path to the advertised next hop. Which technical explanation most directly identifies the cause or design principle?
- BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately.
- For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner.
- BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions.
- A reachable BGP peering session does not itself make a third-party route next hop recursively resolvable.
Explanation
Correct Answer
D:A reachable BGP peering session does not itself make a third-party route next hop recursively resolvable. The appropriate response is to inspect next-hop attributes and IGP reachability; deliberately choose appropriate next-hop-self policy or add valid underlay routes.
Incorrect Answers
A:“BGP route filters must specify permitted exact or range-based prefix matching semantics deliberately” belongs to a separate Border Gateway Protocol (BGP) issue: a prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor. It does not explain the condition tested here.
B:“For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner” belongs to a separate Border Gateway Protocol (BGP) issue: a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops. It does not explain the condition tested here.
C:“BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions” belongs to a separate Border Gateway Protocol (BGP) issue: two eBGP sessions over different transports are expected to provide ECMP but only one forwarding next hop appears. It does not explain the condition tested here.
Question 615
To prevent recurrence of this precise networking failure, which practice should be adopted? An IPv6 transit prefix is hidden because its next-hop address is absent from the correct IPv6 routing table.
- Include inet6-specific next-hop verification in dual-stack BGP peer checklists.
- Review policy ordering with negative tests and explicit default actions on every change.
- Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
- Test expected best-path behavior before modifying LOCAL_PREF across internal peers.
Explanation
Correct Answer
A:Include inet6-specific next-hop verification in dual-stack BGP peer checklists. This guards against BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops.
Incorrect Answers
B:“Review policy ordering with negative tests and explicit default actions on every change” belongs to a separate Border Gateway Protocol (BGP) issue: a BGP export configuration has a broad first match so a specific downstream deny never evaluates the target prefix. It does not explain the condition tested here.
C:“Audit prefix and mask-length boundaries with positive and negative routing-policy tests” belongs to a separate Border Gateway Protocol (BGP) issue: an eBGP import policy unexpectedly accepts more-specific prefixes outside the approved customer allocation. It does not explain the condition tested here.
D:“Test expected best-path behavior before modifying LOCAL_PREF across internal peers” belongs to a separate Border Gateway Protocol (BGP) issue: an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path. It does not explain the condition tested here.
Question 616
To prevent recurrence of this precise networking failure, which practice should be adopted? A branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit.
- Run prefix-boundary tests before enabling area aggregation on an ABR.
- Keep timer settings in shared configuration templates and validate both directions before rollout.
- Document expected external metrics and run primary/backup failover tests during policy changes.
- Classify loopbacks and user-facing links separately from peer links when applying passive templates.
Explanation
Correct Answer
C:Document expected external metrics and run primary/backup failover tests during policy changes. This guards against OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior.
Incorrect Answers
A:“Run prefix-boundary tests before enabling area aggregation on an ABR” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus summarization change hides a needed subnet because the configured address range omits it. It does not explain the condition tested here.
B:“Keep timer settings in shared configuration templates and validate both directions before rollout” belongs to a separate Interior Gateway Protocols (IGPs) issue: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It does not explain the condition tested here.
D:“Classify loopbacks and user-facing links separately from peer links when applying passive templates” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF neighbor remains Down because the routed transit interface was left passive after a site template rollout. It does not explain the condition tested here.
Question 617
To prevent recurrence of this precise networking failure, which practice should be adopted? An EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads.
- Audit ESI consistency and platform-supported multihoming mode across paired leafs.
- Keep route-type purpose and acceptance checks in EVPN troubleshooting runbooks.
- Track route import, MAC mobility and aging during host migration tests.
- Include encapsulation headroom and path MTU tests in EVPN-VXLAN design validation.
Explanation
Correct Answer
D:Include encapsulation headroom and path MTU tests in EVPN-VXLAN design validation. This guards against VXLAN adds encapsulation overhead, so underlay MTU must accommodate the intended overlay frame size.
Incorrect Answers
A:“Audit ESI consistency and platform-supported multihoming mode across paired leafs” belongs to a separate EVPN issue: a shared Ethernet segment loses its fast convergence properties after an ESI-LAG peer receives an inconsistent configuration. It does not explain the condition tested here.
B:“Keep route-type purpose and acceptance checks in EVPN troubleshooting runbooks” belongs to a separate EVPN issue: a fabric advertises Type 3 routes and claims this proves specific remote host MACs are reachable. It does not explain the condition tested here.
C:“Track route import, MAC mobility and aging during host migration tests” belongs to a separate EVPN issue: a new endpoint MAC is learned at a remote VTEP but never reaches the receiving leaf's EVPN control-plane table. It does not explain the condition tested here.
Question 618
A Junos enterprise team investigates this incident: An aggregation broadcast VLAN has a DR/BDR placement that conflicts with the approved design after a maintenance reboot. Which technical explanation most directly identifies the cause or design principle?
- OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication.
- Protocol route advertisement and active-route selection are separate; lower route preference can select a non-OSPF candidate.
- DR/BDR elections on OSPF broadcast networks affect LSA exchange and can be influenced by priority.
- Routing-policy match criteria must align with the source route type and the intended OSPF export behavior.
Explanation
Correct Answer
C:DR/BDR elections on OSPF broadcast networks affect LSA exchange and can be influenced by priority. The appropriate response is to inspect network type, interface priority and existing election state, then plan a controlled DR/BDR change.
Incorrect Answers
A:“OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication” belongs to a separate Interior Gateway Protocols (IGPs) issue: a new IPv6 peering uses OSPFv3 on a retired VLAN unit rather than the active routed transit interface. It does not explain the condition tested here.
B:“Protocol route advertisement and active-route selection are separate; lower route preference can select a non-OSPF candidate” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6 route learned through OSPFv3 is absent from the forwarding table because a more preferred static route covers the same prefix. It does not explain the condition tested here.
D:“Routing-policy match criteria must align with the source route type and the intended OSPF export behavior” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated. It does not explain the condition tested here.
Question 619
A Junos enterprise team investigates this incident: An operator tries to make a remote AS prefer one inbound path using LOCAL_PREF that the remote eBGP peer never receives. Which technical explanation most directly identifies the cause or design principle?
- LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors.
- For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner.
- iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology.
- BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops.
Explanation
Correct Answer
A:LOCAL_PREF is an intra-AS BGP attribute, not a value routinely advertised to external BGP neighbors. The appropriate response is to select a permitted inbound traffic-engineering mechanism with the provider, such as suitable AS-path prepending or agreed communities.
Incorrect Answers
B:“For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner” belongs to a separate Border Gateway Protocol (BGP) issue: a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops. It does not explain the condition tested here.
C:“iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology” belongs to a separate Border Gateway Protocol (BGP) issue: a full-mesh iBGP design is converted to route reflection but one peer is treated as an ordinary nonclient and route propagation fails. It does not explain the condition tested here.
D:“BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops” belongs to a separate Border Gateway Protocol (BGP) issue: an IPv6 transit prefix is hidden because its next-hop address is absent from the correct IPv6 routing table. It does not explain the condition tested here.
Question 620
To prevent recurrence of this precise networking failure, which practice should be adopted? An EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization.
- Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance.
- Verify RADIUS attribute handling and model/release feature support before rolling out dynamic assignment.
- Track hardware, software edition and port family when standardizing access policies.
- Test multi-method paths including success, reject and timeout cases before deployment.
Explanation
Correct Answer
B:Verify RADIUS attribute handling and model/release feature support before rolling out dynamic assignment. This guards against authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary.
Incorrect Answers
A:“Test captive-portal redirects, session expiry and post-login VLAN access in guest-network acceptance” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.
C:“Track hardware, software edition and port family when standardizing access policies” belongs to a separate Layer 2 Authentication and Access Control issue: an engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them. It does not explain the condition tested here.
D:“Test multi-method paths including success, reject and timeout cases before deployment” belongs to a separate Layer 2 Authentication and Access Control issue: two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests