100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 840
To prevent recurrence of this precise networking failure, which practice should be adopted? A remote prefix appears in incoming BGP updates yet never becomes active after a new route policy was applied.
- Include show route hidden and policy term hit checks in BGP troubleshooting playbooks.
- Validate all required BGP address families during dual-stack peer commissioning.
- Include next-hop reachability tests in iBGP and route-reflector deployment acceptance.
- Validate every route-reflector client and failover path in topology inventory before conversion.
Explanation
Correct Answer
A:Include show route hidden and policy term hit checks in BGP troubleshooting playbooks. This guards against a BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session.
Incorrect Answers
B:“Validate all required BGP address families during dual-stack peer commissioning” belongs to a separate Border Gateway Protocol (BGP) issue: BGP peers exchange IPv4 NLRI correctly but a planned IPv6 customer route never appears in inet6.0. It does not explain the condition tested here.
C:“Include next-hop reachability tests in iBGP and route-reflector deployment acceptance” belongs to a separate Border Gateway Protocol (BGP) issue: a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. It does not explain the condition tested here.
D:“Validate every route-reflector client and failover path in topology inventory before conversion” belongs to a separate Border Gateway Protocol (BGP) issue: a route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster. It does not explain the condition tested here.
Question 841
Which suggested shortcut would be especially unsafe for this exact situation? A filter-based VLAN security design uses a rule that catches too many packets and steers legitimate devices into quarantine.
- Include packet-capture verification of S-tag and C-tag transformation in provider handoffs.
- Use a catch-all quarantine match without analyzing which hosts also traverse the interface.
- Audit edge classifications and apply appropriate BPDU protection on true client-facing ports.
- Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned.
Explanation
Correct Answer
B:The tempting alternative fails because overbroad match conditions can cause unauthorized VLAN steering and affect both security and reachability. The supported action is to narrow the match to approved selectors and compare affected packet counters and VLAN assignment.
Incorrect Answers
A:That prevention measure relates to a Q-in-Q service works across transport but the far-end access handoff presents unexpected double tags.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a campus mistakenly enables edge behavior on a switch-to-switch trunk and a loop appears when a backup link activates.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream.; it is not the unsafe shortcut described here.
Question 842
Which suggested shortcut would be especially unsafe for this exact situation? A BGP export configuration has a broad first match so a specific downstream deny never evaluates the target prefix.
- Use multivariable path-selection lab tests before changing MED-based policy.
- Record eBGP peer transport depth and endpoint routing in deployment templates.
- Review next-hop propagation and IGP coverage whenever an eBGP route enters iBGP.
- Append an extra deny at the end and assume it overrides a prior terminal accept.
Explanation
Correct Answer
D:The tempting alternative fails because routing-policy term order and terminal actions determine whether later conditions are evaluated. The supported action is to put specific deny conditions before broad acceptance, and test the policy with representative routes.
Incorrect Answers
A:That prevention measure relates to two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a route-reflector client receives an external destination but lacks the underlay path to the advertised next hop.; it is not the unsafe shortcut described here.
Question 843
A network change is required for the following specific situation: A campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. Which corrective action is most appropriate?
- Inspect registration state and remove stale VLAN membership while preserving necessary registrations.
- Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
- Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.
- Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement.
Explanation
Correct Answer
A:MVRP registrations can persist where membership state or participation has not been updated consistently. Verify this by checking that the retired VLAN disappears from unintended trunks and valid registered VLANs remain reachable.
Incorrect Answers
B:“Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It does not explain the condition tested here.
C:“Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately” belongs to a separate Ethernet Switching and Spanning Tree issue: a network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN. It does not explain the condition tested here.
D:“Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.
Question 844
To prevent recurrence of this precise networking failure, which practice should be adopted? A building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked.
- Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned.
- Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews.
- Track MSTP instance scale and maintain identical region parameters across participating switches.
- Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
Explanation
Correct Answer
B:Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews. This guards against private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles.
Incorrect Answers
A:“Track VLAN lifecycle and MVRP registration ownership as ports are decommissioned” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus migration removes a VLAN at the source while a trunk continues advertising it unexpectedly. It does not explain the condition tested here.
C:“Track MSTP instance scale and maintain identical region parameters across participating switches” belongs to a separate Ethernet Switching and Spanning Tree issue: a large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits. It does not explain the condition tested here.
D:“Scope and monitor tunneled L2 control protocols to prevent control-plane abuse” belongs to a separate Ethernet Switching and Spanning Tree issue: a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. It does not explain the condition tested here.
Question 845
A network change is required for the following specific situation: A campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them. Which corrective action is most appropriate?
- Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.
- Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement.
- Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
- Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop.
Explanation
Correct Answer
A:Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point. Verify this by checking that matching test traffic enters the quarantine VLAN while ordinary traffic stays in the expected VLAN.
Incorrect Answers
B:“Inspect VSTP VLAN membership, root priority and port roles, then repair the intended per-VLAN root arrangement” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.
C:“Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It does not explain the condition tested here.
D:“Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. It does not explain the condition tested here.
Question 846
A network change is required for the following specific situation: A network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. Which corrective action is most appropriate?
- Use precise route-filter match conditions and explicit rejection of unauthorized more-specific routes.
- Inspect received communities and export policy terms, then attach a tested community match and reject rule.
- Inspect next-hop attributes and IGP reachability; deliberately choose appropriate next-hop-self policy or add valid underlay routes.
- Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.
Explanation
Correct Answer
B:Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it. Verify this by checking that a controlled route is withheld from prohibited peers while approved routes retain their expected advertisements.
Incorrect Answers
A:“Use precise route-filter match conditions and explicit rejection of unauthorized more-specific routes” belongs to a separate Border Gateway Protocol (BGP) issue: an eBGP import policy unexpectedly accepts more-specific prefixes outside the approved customer allocation. It does not explain the condition tested here.
C:“Inspect next-hop attributes and IGP reachability; deliberately choose appropriate next-hop-self policy or add valid underlay routes” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP egress advertisement forwards a transit next hop that branch routers cannot resolve, creating traffic blackholes. It does not explain the condition tested here.
D:“Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail” belongs to a separate Border Gateway Protocol (BGP) issue: a new IPv4 BGP prefix has a valid AS path but cannot become active after the IGP stops carrying its next-hop address. It does not explain the condition tested here.
Question 847
A network change is required for the following specific situation: A MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. Which corrective action is most appropriate?
- Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.
- Choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.
- Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.
- Inspect packet exchange and classify the endpoint before selecting a supported fallback method.
Explanation
Correct Answer
A:MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication. Verify this by checking that only the inventoried device has the expected limited connectivity; rogue or unknown hardware is denied.
Incorrect Answers
B:“Choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls” belongs to a separate Layer 2 Authentication and Access Control issue: a captive portal requirement is applied to a headless barcode scanner that has no web browser to follow its redirect. It does not explain the condition tested here.
C:“Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods” belongs to a separate Layer 2 Authentication and Access Control issue: an access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces. It does not explain the condition tested here.
D:“Inspect packet exchange and classify the endpoint before selecting a supported fallback method” belongs to a separate Layer 2 Authentication and Access Control issue: a switch logs EAP timeout while the endpoint has no 802.1X supplicant, yet the operator rotates valid RADIUS passwords repeatedly. It does not explain the condition tested here.
Question 848
To prevent recurrence of this precise networking failure, which practice should be adopted? A vendor handset discovers its neighbor using basic LLDP but does not learn the configured network policy for voice tagging.
- Include end-to-end marking tests when deploying voice VLANs and new phone models.
- Validate PD power profiles and test peak draw rather than idle boot alone.
- Include LLDP-MED capabilities and network-policy TLVs in phone-vendor acceptance testing.
- Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
Explanation
Correct Answer
C:Include LLDP-MED capabilities and network-policy TLVs in phone-vendor acceptance testing. This guards against LLDP-MED extends device discovery with telephony-related network-policy TLVs that need compatible endpoint behavior.
Incorrect Answers
A:“Include end-to-end marking tests when deploying voice VLANs and new phone models” belongs to a separate IP Telephony Features issue: a handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design. It does not explain the condition tested here.
B:“Validate PD power profiles and test peak draw rather than idle boot alone” belongs to a separate IP Telephony Features issue: a phone's LLDP-negotiated power demand exceeds its access port's allocated PoE limit and it repeatedly restarts. It does not explain the condition tested here.
D:“Capacity-plan PoE power classes and reserved headroom before connecting new powered devices” belongs to a separate IP Telephony Features issue: a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget. It does not explain the condition tested here.
Question 849
To prevent recurrence of this precise networking failure, which practice should be adopted? A redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local.
- Classify loopbacks and user-facing links separately from peer links when applying passive templates.
- Use named prefix lists and regression tests for approved and denied redistribution cases.
- Specify preferred OSPF DR candidates on shared transit segments and account for non-preemptive elections.
- Run prefix-boundary tests before enabling area aggregation on an ABR.
Explanation
Correct Answer
B:Use named prefix lists and regression tests for approved and denied redistribution cases. This guards against unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability.
Incorrect Answers
A:“Classify loopbacks and user-facing links separately from peer links when applying passive templates” belongs to a separate Interior Gateway Protocols (IGPs) issue: a distribution node learns connected subnets but never sends Hello packets on its OSPF transit port due to passive-interface policy. It does not explain the condition tested here.
C:“Specify preferred OSPF DR candidates on shared transit segments and account for non-preemptive elections” belongs to a separate Interior Gateway Protocols (IGPs) issue: an aggregation broadcast VLAN has a DR/BDR placement that conflicts with the approved design after a maintenance reboot. It does not explain the condition tested here.
D:“Run prefix-boundary tests before enabling area aggregation on an ABR” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus summarization change hides a needed subnet because the configured address range omits it. It does not explain the condition tested here.
Question 850
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: An OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated.
- Restart the entire OSPFv2 process and assume this fixes a missing OSPFv3 loopback.
- Inspect the active local default and export term conditions; match only the authorized static default source.
- A designated external default appears at downstream routers without leaking unrelated static prefixes.
- Configure IPv4 OSPFv2 alone and expect it to populate IPv6 unicast routes automatically.
- Add a catch-all accept at the end of the policy to bypass the source-type error.
Explanation
Correct Answers
B:Inspect the active local default and export term conditions; match only the authorized static default source. This addresses the dependency that routing-policy match criteria must align with the source route type and the intended OSPF export behavior.
C:A designated external default appears at downstream routers without leaking unrelated static prefixes. The specific steps required are to inspect the active local default and export term conditions; match only the authorized static default source.
Incorrect Answers
A:“Restart the entire OSPFv2 process and assume this fixes a missing OSPFv3 loopback” is an unsafe response to a different problem: OSPFv3 peering comes up but the desired IPv6 loopback is not in the routing database after a rollout. It is not a valid fix here.
D:“Configure IPv4 OSPFv2 alone and expect it to populate IPv6 unicast routes automatically” is an unsafe response to a different problem: an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. It is not a valid fix here.
E:“Add a catch-all accept at the end of the policy to bypass the source-type error” does not address routing-policy match criteria must align with the source route type and the intended OSPF export behavior.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests