Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 88

Question 870

To prevent recurrence of this precise networking failure, which practice should be adopted? A shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design.

  1. Test each critical VLAN's root bridge and forwarding path after VSTP updates.
  2. Test private-port isolation and uplink reachability after access topology changes.
  3. Include MVRP adjacency and registration checks in trunk-change reviews.
  4. Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.

Explanation

Correct Answer

B:

Test private-port isolation and uplink reachability after access topology changes. This guards against private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink.

Incorrect Answers

A:

“Test each critical VLAN's root bridge and forwarding path after VSTP updates” belongs to a separate Ethernet Switching and Spanning Tree issue: a VSTP network intended to send voice and data VLANs over different active paths instead blocks both on the same uplink. It does not explain the condition tested here.

C:

“Include MVRP adjacency and registration checks in trunk-change reviews” belongs to a separate Ethernet Switching and Spanning Tree issue: a new switch automatically discovers VLAN registrations on one trunk, but an intermediate trunk lacks MVRP participation and blocks the VLAN. It does not explain the condition tested here.

D:

“Scope and monitor tunneled L2 control protocols to prevent control-plane abuse” belongs to a separate Ethernet Switching and Spanning Tree issue: an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently. It does not explain the condition tested here.

Question 871

To prevent recurrence of this precise networking failure, which practice should be adopted? A full-mesh iBGP design is converted to route reflection but one peer is treated as an ordinary nonclient and route propagation fails.

  1. Use multivariable path-selection lab tests before changing MED-based policy.
  2. Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
  3. Validate every route-reflector client and failover path in topology inventory before conversion.
  4. Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes.

Explanation

Correct Answer

C:

Validate every route-reflector client and failover path in topology inventory before conversion. This guards against iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology.

Incorrect Answers

A:

“Use multivariable path-selection lab tests before changing MED-based policy” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.

B:

“Audit prefix and mask-length boundaries with positive and negative routing-policy tests” belongs to a separate Border Gateway Protocol (BGP) issue: an eBGP import policy unexpectedly accepts more-specific prefixes outside the approved customer allocation. It does not explain the condition tested here.

D:

“Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes” belongs to a separate Border Gateway Protocol (BGP) issue: a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. It does not explain the condition tested here.

Question 872

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: An iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0.

  1. Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.
  2. Assume attaching a BGP community automatically prevents all external redistribution without policy.
  3. The previously hidden BGP prefix resolves its next hop and becomes an eligible route.
  4. Expect a locally set LOCAL_PREF value to propagate unchanged over standard eBGP to another AS.
  5. Lower AS-path length without fixing the unreachable BGP next-hop address.

Explanation

Correct Answers

A:

Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail. This addresses the dependency that BGP route selection first requires the BGP next hop to resolve through the appropriate routing table.

C:

The previously hidden BGP prefix resolves its next hop and becomes an eligible route. The specific steps required are to restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.

Incorrect Answers

B:

“Assume attaching a BGP community automatically prevents all external redistribution without policy” is an unsafe response to a different problem: a provider-facing policy stops honoring a route-tag community after a new import policy changes the attached communities. It is not a valid fix here.

D:

“Expect a locally set LOCAL_PREF value to propagate unchanged over standard eBGP to another AS” is an unsafe response to a different problem: a dual-homed site changes internal LOCAL_PREF but sees no change in the other autonomous system's inbound traffic choice. It is not a valid fix here.

E:

“Lower AS-path length without fixing the unreachable BGP next-hop address” does not address BGP route selection first requires the BGP next hop to resolve through the appropriate routing table.

Question 873

Which suggested shortcut would be especially unsafe for this exact situation? A switch rollout splits a team that should communicate within one PVLAN community, while protecting it from another community.

  1. Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
  2. Make every tenant port promiscuous simply to restore one workgroup's access.
  3. Document outer/inner VLAN roles and test tag stripping and preservation at service boundaries.
  4. Keep explicit root priority policy and validate elections after device replacement.

Explanation

Correct Answer

B:

The tempting alternative fails because a private VLAN community allows permitted communication within its community; isolated behavior is stricter. The supported action is to map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated.

Incorrect Answers

A:

That prevention measure relates to an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN.; it is not the unsafe shortcut described here.

Question 874

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster.

  1. Use only the MED field as guaranteed proof of the selected route regardless of preceding BGP attributes.
  2. Disable all iBGP loop protection and expect the route-reflector hierarchy to be unnecessary.
  3. The downstream client learns approved prefixes and cluster-loop checks remain operational.
  4. Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration.
  5. Expect a locally set LOCAL_PREF value to propagate unchanged over standard eBGP to another AS.

Explanation

Correct Answers

C:

The downstream client learns approved prefixes and cluster-loop checks remain operational. The specific steps required are to inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration.

D:

Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration. This addresses the dependency that iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology.

Incorrect Answers

A:

“Use only the MED field as guaranteed proof of the selected route regardless of preceding BGP attributes” is an unsafe response to a different problem: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It is not a valid fix here.

B:

“Disable all iBGP loop protection and expect the route-reflector hierarchy to be unnecessary” does not address iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology.

E:

“Expect a locally set LOCAL_PREF value to propagate unchanged over standard eBGP to another AS” is an unsafe response to a different problem: a dual-homed site changes internal LOCAL_PREF but sees no change in the other autonomous system's inbound traffic choice. It is not a valid fix here.

Question 875

A network change is required for the following specific situation: A campus multicast application migrates ASM clients to SSM but does not update the source-qualified membership requests. Which corrective action is most appropriate?

  1. Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
  2. Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
  3. Verify anycast RP address and supported source synchronization method across the participating RP nodes.
  4. Update receiver memberships to use the approved source and group, and validate end-to-end (S,G) trees.

Explanation

Correct Answer

D:

ASM and SSM use different membership and source-selection semantics; an SSM receiver must identify its desired sender. Verify this by checking that only the specified source delivers data to receivers of the chosen SSM group.

Incorrect Answers

A:

“Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports” belongs to a separate IP Multicast issue: an access VLAN floods every multicast packet because IGMP snooping state was lost during migration. It does not explain the condition tested here.

B:

“Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding” belongs to a separate IP Multicast issue: a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. It does not explain the condition tested here.

C:

“Verify anycast RP address and supported source synchronization method across the participating RP nodes” belongs to a separate IP Multicast issue: a second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it. It does not explain the condition tested here.

Question 876

Select THREE complementary corrective, verification, or preventive controls for this scenario: A replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring.

  1. Inspect IPv6 interface addresses and OSPFv3 interface participation, then add the intended loopback advertisement within policy.
  2. Change only BGP keepalive values and assume OSPF timers automatically follow.
  3. The remote inet6.0 table learns the intended loopback and reachability testing succeeds.
  4. Restart the entire OSPFv2 process and assume this fixes a missing OSPFv3 loopback.
  5. Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance.
  6. Make every edge interface active to OSPF regardless of whether a routing peer exists.

Explanation

Correct Answers

A:

Correction: An established OSPFv3 neighbor does not prove every desired IPv6 interface prefix is included in the protocol topology.

C:

Confirmation: Inspect IPv6 interface addresses and OSPFv3 interface participation, then add the intended loopback advertisement within policy.

E:

Prevention of recurrence: An established OSPFv3 neighbor does not prove every desired IPv6 interface prefix is included in the protocol topology.

Incorrect Answers

B:

“Change only BGP keepalive values and assume OSPF timers automatically follow” is an unsafe response to a different problem: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It is not a valid fix here.

D:

“Restart the entire OSPFv2 process and assume this fixes a missing OSPFv3 loopback” does not address an established OSPFv3 neighbor does not prove every desired IPv6 interface prefix is included in the protocol topology.

F:

“Make every edge interface active to OSPF regardless of whether a routing peer exists” is an unsafe response to a different problem: an OSPF neighbor remains Down because the routed transit interface was left passive after a site template rollout. It is not a valid fix here.

Question 877

The team believes it has resolved this Junos issue: An engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them. Which observation best verifies the specific intended result?

  1. The registered device is authorized with limited access; an unknown MAC remains blocked.
  2. The known device reaches only permitted destinations and cannot reach employee or management resources.
  3. Validation shows only supported options in use and the intended access-denial/fallback behavior.
  4. Both intended endpoints receive their authorized VLAN/policy without permitting unapproved devices.

Explanation

Correct Answer

C:

Validation shows only supported options in use and the intended access-denial/fallback behavior. This checks the relevant result after consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.

Incorrect Answers

A:

“The registered device is authorized with limited access; an unknown MAC remains blocked” belongs to a separate Layer 2 Authentication and Access Control issue: a non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. It does not explain the condition tested here.

B:

“The known device reaches only permitted destinations and cannot reach employee or management resources” belongs to a separate Layer 2 Authentication and Access Control issue: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It does not explain the condition tested here.

D:

“Both intended endpoints receive their authorized VLAN/policy without permitting unapproved devices” belongs to a separate Layer 2 Authentication and Access Control issue: a telephony desk requires multiple authenticated identities while the switch policy allows only one active supplicant. It does not explain the condition tested here.

Question 878

Select THREE complementary corrective, verification, or preventive controls for this scenario: A shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade.

  1. Include MVRP adjacency and registration checks in trunk-change reviews.
  2. Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop.
  3. Use a catch-all quarantine match without analyzing which hosts also traverse the interface.
  4. Assume that one switch's locally created VLAN is automatically registered on all links with MVRP disabled.
  5. The VLAN registration propagates to the intended downstream trunk and reaches its member ports.
  6. Make every switch-to-switch uplink an edge port to accelerate convergence.

Explanation

Correct Answers

A:

Prevention of recurrence: MVRP distributes VLAN registration information across participating links; a gap can stop propagation.

B:

Correction: MVRP distributes VLAN registration information across participating links; a gap can stop propagation.

E:

Confirmation: Inspect MVRP state and permitted VLANs on each trunk; enable supported participation on the missing hop.

Incorrect Answers

C:

“Use a catch-all quarantine match without analyzing which hosts also traverse the interface” is an unsafe response to a different problem: a filter-based VLAN security design uses a rule that catches too many packets and steers legitimate devices into quarantine. It is not a valid fix here.

D:

“Assume that one switch's locally created VLAN is automatically registered on all links with MVRP disabled” does not address MVRP distributes VLAN registration information across participating links; a gap can stop propagation.

F:

“Make every switch-to-switch uplink an edge port to accelerate convergence” is an unsafe response to a different problem: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It is not a valid fix here.

Question 879

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: An OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health.

  1. Change only BGP keepalive values and assume OSPF timers automatically follow.
  2. Assume increasing OSPF priority immediately preempts an existing healthy DR on every device.
  3. Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy.
  4. Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
  5. The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests.

Explanation

Correct Answers

D:

Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface. This addresses the dependency that IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges.

E:

The affected link passes OSPFv3 neighbor and IPv6 reachability checks rather than IPv4-only tests. The specific steps required are to check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.

Incorrect Answers

A:

“Change only BGP keepalive values and assume OSPF timers automatically follow” is an unsafe response to a different problem: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It is not a valid fix here.

B:

“Assume increasing OSPF priority immediately preempts an existing healthy DR on every device” is an unsafe response to a different problem: a shared multiaccess segment elects an undesired OSPF DR after new routers are connected, and control-plane load rises. It is not a valid fix here.

C:

“Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy” does not address IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges.

Question 880

A Junos enterprise team investigates this incident: An EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. Which technical explanation most directly identifies the cause or design principle?

  1. EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane.
  2. EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set.
  3. VXLAN encapsulates overlay traffic across an IP underlay; VTEP reachability is necessary even with valid BGP EVPN control-plane state.
  4. EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.

Explanation

Correct Answer

D:

EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops. The appropriate response is to inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.

Incorrect Answers

A:

“EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane” belongs to a separate EVPN issue: a host moves between leafs and the destination leaf still forwards toward the previous MAC location. It does not explain the condition tested here.

B:

“EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set” belongs to a separate EVPN issue: a VNI is active on two leafs but unknown-unicast or broadcast replication never reaches the remote side. It does not explain the condition tested here.

C:

“VXLAN encapsulates overlay traffic across an IP underlay; VTEP reachability is necessary even with valid BGP EVPN control-plane state” belongs to a separate EVPN issue: a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.