100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 900
Which suggested shortcut would be especially unsafe for this exact situation? Equal candidate BGP routes are visible but no multipath forwarding entry is installed because eligibility or policy differs.
- Add a second BGP neighbor and assume the forwarding table automatically load-balances every route.
- Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes.
- Maintain expected BGP attribute decisions for every primary/secondary transit policy.
- Use multivariable path-selection lab tests before changing MED-based policy.
Explanation
Correct Answer
A:The tempting alternative fails because BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions. The supported action is to compare BGP best-path and multipath eligibility conditions, then enable approved multipath behavior and validate forwarding.
Incorrect Answers
B:That prevention measure relates to a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a branch dual-transit design sees the higher-preference provider route win even though its AS path has more hops.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an engineer incorrectly assumes a lower MED overrides a larger LOCAL_PREF, when both transit candidates are eligible.; it is not the unsafe shortcut described here.
Question 901
The team believes it has resolved this Junos issue: An emergency intercom can establish Ethernet link but loses power during activity because its PD class is not supported by that port. Which observation best verifies the specific intended result?
- Tagged voice packets retain the intended service class through the access and aggregation paths.
- Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface.
- The device stays powered during peak consumption and Junos reports no power-denial events.
- The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN.
Explanation
Correct Answer
C:The device stays powered during peak consumption and Junos reports no power-denial events. This checks the relevant result after inspect PoE class, per-port priority and available chassis budget, and move to a supported powered port if needed.
Incorrect Answers
A:“Tagged voice packets retain the intended service class through the access and aggregation paths” belongs to a separate IP Telephony Features issue: a handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design. It does not explain the condition tested here.
B:“Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface” belongs to a separate IP Telephony Features issue: a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature. It does not explain the condition tested here.
D:“The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.
Question 902
A network change is required for the following specific situation: A RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response. Which corrective action is most appropriate?
- Inspect packet exchange and classify the endpoint before selecting a supported fallback method.
- Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
- Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.
- Assign the authenticated device to the authorized restricted network profile and verify effective VLAN/filter.
Explanation
Correct Answer
A:Supplicant absence is a distinct failure from an invalid credential or unreachable authentication server. Verify this by checking that the observed authentication state identifies missing supplicant response, and the approved method onboards the endpoint.
Incorrect Answers
B:“Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform” belongs to a separate Layer 2 Authentication and Access Control issue: after a RADIUS outage, the access switch opens ports broadly instead of applying the approved restricted server-fail VLAN. It does not explain the condition tested here.
C:“Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls” belongs to a separate Layer 2 Authentication and Access Control issue: a printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy. It does not explain the condition tested here.
D:“Assign the authenticated device to the authorized restricted network profile and verify effective VLAN/filter” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS policy authenticates a known camera but applies the broad employee VLAN instead of a camera-only network. It does not explain the condition tested here.
Question 903
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A large campus places hundreds of VLANs in separate spanning-tree instances and reaches scale or CPU limits.
- Create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior.
- Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated.
- Use a catch-all quarantine match without analyzing which hosts also traverse the interface.
- Create an independent VSTP instance for every VLAN without checking platform scaling limits.
- The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion.
Explanation
Correct Answers
A:Create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior. This addresses the dependency that MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.
E:The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion. The specific steps required are to create an approved MSTP region and VLAN-to-instance mapping, then verify root and port role behavior.
Incorrect Answers
B:“Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated” is an unsafe response to a different problem: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It is not a valid fix here.
C:“Use a catch-all quarantine match without analyzing which hosts also traverse the interface” is an unsafe response to a different problem: a filter-based VLAN security design uses a rule that catches too many packets and steers legitimate devices into quarantine. It is not a valid fix here.
D:“Create an independent VSTP instance for every VLAN without checking platform scaling limits” does not address MSTP maps VLANs into a smaller set of spanning-tree instances, providing scalable per-group path control.
Question 904
Which suggested shortcut would be especially unsafe for this exact situation? Video gets dropped under congestion despite spare capacity because its queue has a too-small delay buffer.
- Increase every queue buffer without considering latency, memory or scheduling priority.
- Test ingress classification separately from egress rewrite at every trust boundary.
- Keep a documented forwarding-class inventory and test default mappings after service changes.
- Plan buffer and shaping rates against provider handoff capacity and expected burst size.
Explanation
Correct Answer
A:The tempting alternative fails because queue schedulers and buffer parameters influence service rate and delay/drop behavior at congested egress. The supported action is to review queue buffer and scheduler allocations against traffic measurements and apply a bounded adjustment.
Incorrect Answers
B:That prevention measure relates to a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a forwarding-class configuration sends critical routing packets to a queue used for bulk backups and adjacency stability degrades under load.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss.; it is not the unsafe shortcut described here.
Question 905
Select THREE complementary corrective, verification, or preventive controls for this scenario: A PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point.
- PIM joins build the intended shared tree and the requested group begins forwarding to subscribers.
- Assume IGMP membership on the access switch alone builds an end-to-end PIM ASM tree.
- Check group-to-RP mapping and RP reachability, then repair the RP discovery or explicit mapping.
- Use a unique group name as the only security boundary and rely on routers to infer its scope.
- Maintain consistent RP mappings and failover tests across multicast routers.
- Treat SSM group membership as source-agnostic and subscribe to the group without source information.
Explanation
Correct Answers
A:Confirmation: Check group-to-RP mapping and RP reachability, then repair the RP discovery or explicit mapping.
C:Correction: PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
E:Prevention of recurrence: PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
Incorrect Answers
B:“Assume IGMP membership on the access switch alone builds an end-to-end PIM ASM tree” does not address PIM sparse-mode ASM builds shared-tree state toward a reachable RP, and an incorrect RP mapping can prevent service.
D:“Use a unique group name as the only security boundary and rely on routers to infer its scope” is an unsafe response to a different problem: a laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab. It is not a valid fix here.
F:“Treat SSM group membership as source-agnostic and subscribe to the group without source information” is an unsafe response to a different problem: a streaming application expects a source-specific group to accept traffic from any origin, contrary to its (S,G) subscription. It is not a valid fix here.
Question 906
To prevent recurrence of this precise networking failure, which practice should be adopted? A RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response.
- Review MAC-device inventory, spoofing exposure and expiry before using MAC-based authorization.
- Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions.
- Separate EAP silence, reject and timeout counters in authentication operational monitoring.
- Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises.
Explanation
Correct Answer
C:Separate EAP silence, reject and timeout counters in authentication operational monitoring. This guards against supplicant absence is a distinct failure from an invalid credential or unreachable authentication server.
Incorrect Answers
A:“Review MAC-device inventory, spoofing exposure and expiry before using MAC-based authorization” belongs to a separate Layer 2 Authentication and Access Control issue: an industrial sensor lacks a supplicant but needs restricted network authorization through a centralized identity service. It does not explain the condition tested here.
B:“Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions” belongs to a separate Layer 2 Authentication and Access Control issue: a printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy. It does not explain the condition tested here.
D:“Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises” belongs to a separate Layer 2 Authentication and Access Control issue: after a RADIUS outage, the access switch opens ports broadly instead of applying the approved restricted server-fail VLAN. It does not explain the condition tested here.
Question 907
A network change is required for the following specific situation: A route policy lacks an explicit intended default action, and unmatched BGP prefixes behave differently than planned. Which corrective action is most appropriate?
- Document and test terminal accept or reject behavior along with next-term and next-policy handling.
- Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence.
- Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.
- Inspect received communities and export policy terms, then attach a tested community match and reject rule.
Explanation
Correct Answer
A:Routing-policy evaluation depends on term matches, flow-control actions and the policy chain, including what happens on no match. Verify this by checking that positive and negative prefix tests traverse the expected policy terms and produce approved import/export outcomes.
Incorrect Answers
B:“Read all relevant candidate attributes and apply policy consistent with intended tie-breaker precedence” belongs to a separate Border Gateway Protocol (BGP) issue: an engineer incorrectly assumes a lower MED overrides a larger LOCAL_PREF, when both transit candidates are eligible. It does not explain the condition tested here.
C:“Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. It does not explain the condition tested here.
D:“Inspect received communities and export policy terms, then attach a tested community match and reject rule” belongs to a separate Border Gateway Protocol (BGP) issue: a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. It does not explain the condition tested here.
Question 908
Which suggested shortcut would be especially unsafe for this exact situation? A WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss.
- Assume any policing rule provides the same paced, buffered behavior as egress shaping.
- Document trusted-marking boundaries and test both matched and unmatched multifield traffic.
- Keep a documented forwarding-class inventory and test default mappings after service changes.
- Establish congestion thresholds and monitor starvation as part of queue-priority design.
Explanation
Correct Answer
A:The tempting alternative fails because shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract. The supported action is to configure supported egress shaping at the bottleneck and verify throughput and queue behavior.
Incorrect Answers
B:That prevention measure relates to an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier.; it is not the unsafe shortcut described here.
C:That prevention measure relates to an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy.; it is not the unsafe shortcut described here.
Question 909
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight.
- Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration.
- Increase every queue buffer without considering latency, memory or scheduling priority.
- Map every packet to the lowest loss priority regardless of its out-of-profile status.
- Controlled traffic probes pass valid bursts without permitting sustained rate violations.
- Measure burst patterns and adjust the policer burst configuration within the authorized service contract.
Explanation
Correct Answers
D:Controlled traffic probes pass valid bursts without permitting sustained rate violations. The specific steps required are to measure burst patterns and adjust the policer burst configuration within the authorized service contract.
E:Measure burst patterns and adjust the policer burst configuration within the authorized service contract. This addresses the dependency that policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.
Incorrect Answers
A:“Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration” does not address policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.
B:“Increase every queue buffer without considering latency, memory or scheduling priority” is an unsafe response to a different problem: a backup traffic queue consumes too much buffer and latency-sensitive applications starve during peak bursts. It is not a valid fix here.
C:“Map every packet to the lowest loss priority regardless of its out-of-profile status” is an unsafe response to a different problem: a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class. It is not a valid fix here.
Question 910
To prevent recurrence of this precise networking failure, which practice should be adopted? A provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior.
- Test both average-rate enforcement and microburst tolerance for new policer profiles.
- Establish congestion thresholds and monitor starvation as part of queue-priority design.
- Differentiate ingress policing from egress shaping when designing bandwidth controls.
- Test ingress classification separately from egress rewrite at every trust boundary.
Explanation
Correct Answer
D:Test ingress classification separately from egress rewrite at every trust boundary. This guards against Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings.
Incorrect Answers
A:“Test both average-rate enforcement and microburst tolerance for new policer profiles” belongs to a separate Class of Service (CoS) issue: a traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. It does not explain the condition tested here.
B:“Establish congestion thresholds and monitor starvation as part of queue-priority design” belongs to a separate Class of Service (CoS) issue: a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. It does not explain the condition tested here.
C:“Differentiate ingress policing from egress shaping when designing bandwidth controls” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests