Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 92

Question 910

To prevent recurrence of this precise networking failure, which practice should be adopted? A provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior.

  1. Test both average-rate enforcement and microburst tolerance for new policer profiles.
  2. Establish congestion thresholds and monitor starvation as part of queue-priority design.
  3. Differentiate ingress policing from egress shaping when designing bandwidth controls.
  4. Test ingress classification separately from egress rewrite at every trust boundary.

Explanation

Correct Answer

D:

Test ingress classification separately from egress rewrite at every trust boundary. This guards against Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings.

Incorrect Answers

A:

“Test both average-rate enforcement and microburst tolerance for new policer profiles” belongs to a separate Class of Service (CoS) issue: a traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. It does not explain the condition tested here.

B:

“Establish congestion thresholds and monitor starvation as part of queue-priority design” belongs to a separate Class of Service (CoS) issue: a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. It does not explain the condition tested here.

C:

“Differentiate ingress policing from egress shaping when designing bandwidth controls” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.

Question 911

Select THREE complementary corrective, verification, or preventive controls for this scenario: An access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed.

  1. Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy.
  2. Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing.
  3. Keep a documented forwarding-class inventory and test default mappings after service changes.
  4. Control-plane-related traffic receives the expected queue treatment under simulated load.
  5. Assume more queues automatically improve latency even if control traffic remains mapped to a congested queue.
  6. Review the forwarding class and queue map for control and data traffic and apply the intended assignments.

Explanation

Correct Answers

C:

Prevention of recurrence: Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays.

D:

Confirmation: Review the forwarding class and queue map for control and data traffic and apply the intended assignments.

F:

Correction: Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays.

Incorrect Answers

A:

“Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy” is an unsafe response to a different problem: a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. It is not a valid fix here.

B:

“Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing” is an unsafe response to a different problem: a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. It is not a valid fix here.

E:

“Assume more queues automatically improve latency even if control traffic remains mapped to a congested queue” does not address forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays.

Question 912

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A customer access switch trusts external CoS bits and redistributes high-priority markings to all guest traffic.

  1. Define a controlled rewrite map for each class and verify high-priority markings remain restricted.
  2. Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing.
  3. Let all untrusted clients self-select expedited forwarding marks without verification.
  4. Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration.
  5. Only approved media streams leave with high-priority code points; backup traffic uses its designated mark.

Explanation

Correct Answers

A:

Define a controlled rewrite map for each class and verify high-priority markings remain restricted. This addresses the dependency that CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings.

E:

Only approved media streams leave with high-priority code points; backup traffic uses its designated mark. The specific steps required are to define a controlled rewrite map for each class and verify high-priority markings remain restricted.

Incorrect Answers

B:

“Mark every forwarding class strict-high with no attention to starvation or bounded resource sharing” is an unsafe response to a different problem: two queues use the same scheduler priority, but the business expects one to always win during contention. It is not a valid fix here.

C:

“Let all untrusted clients self-select expedited forwarding marks without verification” does not address CoS rewrite must reflect trusted classifications and intended forwarding policy, not arbitrary source markings.

D:

“Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration” is an unsafe response to a different problem: a traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. It is not a valid fix here.

Question 913

A Junos enterprise team investigates this incident: A campus has configured forwarding classes and schedulers but one uplink carries all traffic through default service because association is missing. Which technical explanation most directly identifies the cause or design principle?

  1. Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays.
  2. Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.
  3. Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface.
  4. Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract.

Explanation

Correct Answer

C:

Egress scheduling requires the intended schedulers and their mapping to be applied on the outgoing interface. The appropriate response is to associate the approved scheduler map with the correct egress interface and confirm class queue counters.

Incorrect Answers

A:

“Forwarding classes select output queues; an incorrect class-to-queue association can cause head-of-line delays” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.

B:

“Policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic” belongs to a separate Class of Service (CoS) issue: an uplink meets long-term bandwidth policy but legitimate short bursts exceed the token-bucket allowance. It does not explain the condition tested here.

D:

“Shaping buffers and schedules outgoing traffic to a rate, unlike policing which marks or discards traffic exceeding a contract” belongs to a separate Class of Service (CoS) issue: a branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. It does not explain the condition tested here.

Question 914

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification.

  1. Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power.
  2. Tagged voice packets retain the intended service class through the access and aggregation paths.
  3. Assume enabling ordinary LLDP globally is guaranteed to activate every LLDP-MED policy automatically.
  4. Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
  5. Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN.

Explanation

Correct Answers

B:

Tagged voice packets retain the intended service class through the access and aggregation paths. The specific steps required are to verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.

D:

Verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media. This addresses the dependency that voice VLAN placement and CoS marking are related but separate; correct VLAN tagging does not guarantee priority handling.

Incorrect Answers

A:

“Increase data VLAN bandwidth as the only remedy for a handset that is not receiving enough electrical power” is an unsafe response to a different problem: a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. It is not a valid fix here.

C:

“Assume enabling ordinary LLDP globally is guaranteed to activate every LLDP-MED policy automatically” is an unsafe response to a different problem: a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature. It is not a valid fix here.

E:

“Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN” does not address voice VLAN placement and CoS marking are related but separate; correct VLAN tagging does not guarantee priority handling.

Question 915

A Junos enterprise team investigates this incident: A multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. Which technical explanation most directly identifies the cause or design principle?

  1. EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane.
  2. EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence.
  3. EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set.
  4. VXLAN adds encapsulation overhead, so underlay MTU must accommodate the intended overlay frame size.

Explanation

Correct Answer

B:

EVPN Ethernet segment identifiers associate redundant attachments with one multihoming segment and support coordinated convergence. The appropriate response is to align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes.

Incorrect Answers

A:

“EVPN Type 2 MAC/IP advertisement carries endpoint reachability and mobility information in the control plane” belongs to a separate EVPN issue: a host moves between leafs and the destination leaf still forwards toward the previous MAC location. It does not explain the condition tested here.

C:

“EVPN Type 3 inclusive multicast routes announce interested VTEPs for a broadcast domain's BUM replication set” belongs to a separate EVPN issue: a VNI is active on two leafs but unknown-unicast or broadcast replication never reaches the remote side. It does not explain the condition tested here.

D:

“VXLAN adds encapsulation overhead, so underlay MTU must accommodate the intended overlay frame size” belongs to a separate EVPN issue: an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. It does not explain the condition tested here.

Question 916

A network change is required for the following specific situation: An EAP-compliant endpoint authenticates while the required policy attribute is absent or ignored in switch port authorization. Which corrective action is most appropriate?

  1. Check returned RADIUS attributes and supported platform software, then enforce a valid authorization assignment.
  2. Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
  3. Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.
  4. Check authentication result classification and map the rejected user to an appropriate deny or reject response.

Explanation

Correct Answer

A:

Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary. Verify this by checking that the switch reports an authorized session with the intended VLAN and access policy.

Incorrect Answers

B:

“Use a supported restricted server-fail policy and validate failure handling on the specific Junos platform” belongs to a separate Layer 2 Authentication and Access Control issue: after a RADIUS outage, the access switch opens ports broadly instead of applying the approved restricted server-fail VLAN. It does not explain the condition tested here.

C:

“Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods” belongs to a separate Layer 2 Authentication and Access Control issue: an access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces. It does not explain the condition tested here.

D:

“Check authentication result classification and map the rejected user to an appropriate deny or reject response” belongs to a separate Layer 2 Authentication and Access Control issue: a credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants. It does not explain the condition tested here.

Question 917

Select THREE complementary corrective, verification, or preventive controls for this scenario: A private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs.

  1. Configure supported L2PT for the required control protocols and verify provider-edge handling.
  2. Scope and monitor tunneled L2 control protocols to prevent control-plane abuse.
  3. Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled.
  4. Make every tenant port promiscuous simply to restore one workgroup's access.
  5. Make every switch-to-switch uplink an edge port to accelerate convergence.
  6. The customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology.

Explanation

Correct Answers

A:

Correction: Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.

B:

Prevention of recurrence: Layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.

F:

Confirmation: Configure supported L2PT for the required control protocols and verify provider-edge handling.

Incorrect Answers

C:

“Enable ordinary Q-in-Q tagging alone and assume every customer control protocol is necessarily tunneled” does not address layer 2 protocol tunneling preserves selected customer control traffic across a service where ordinary data tagging is not enough.

D:

“Make every tenant port promiscuous simply to restore one workgroup's access” is an unsafe response to a different problem: members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication. It is not a valid fix here.

E:

“Make every switch-to-switch uplink an edge port to accelerate convergence” is an unsafe response to a different problem: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It is not a valid fix here.

Question 918

A Junos enterprise team investigates this incident: A branch uplink uses area 0.0.0.6 on one router and area 0.0.0.9 on its peer after a template copy. Which technical explanation most directly identifies the cause or design principle?

  1. OSPF neighbors must agree on the area context to form adjacency on the common link.
  2. OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior.
  3. IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges.
  4. OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication.

Explanation

Correct Answer

A:

OSPF neighbors must agree on the area context to form adjacency on the common link. The appropriate response is to compare configured interface areas with the approved topology and put both interfaces in the intended matching area.

Incorrect Answers

B:

“OSPF external route costs and metric types affect path choice and must reflect intended topology and failover behavior” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF policy update redistributes a route without an appropriate external metric, shifting traffic to a slow backup. It does not explain the condition tested here.

C:

“IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.

D:

“OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear. It does not explain the condition tested here.

Question 919

A Junos enterprise team investigates this incident: An iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. Which technical explanation most directly identifies the cause or design principle?

  1. BGP route selection first requires the BGP next hop to resolve through the appropriate routing table.
  2. Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it.
  3. A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session.
  4. iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology.

Explanation

Correct Answer

A:

BGP route selection first requires the BGP next hop to resolve through the appropriate routing table. The appropriate response is to restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.

Incorrect Answers

B:

“Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it” belongs to a separate Border Gateway Protocol (BGP) issue: a provider-facing policy stops honoring a route-tag community after a new import policy changes the attached communities. It does not explain the condition tested here.

C:

“A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session” belongs to a separate Border Gateway Protocol (BGP) issue: a Junos route is hidden by import policy, but the team troubleshoots only local physical interfaces. It does not explain the condition tested here.

D:

“iBGP-learned routes are not freely re-advertised to all iBGP neighbors without appropriate reflection or topology” belongs to a separate Border Gateway Protocol (BGP) issue: a full-mesh iBGP design is converted to route reflection but one peer is treated as an ordinary nonclient and route propagation fails. It does not explain the condition tested here.

Question 920

The team believes it has resolved this Junos issue: A WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. Which observation best verifies the specific intended result?

  1. During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic.
  2. Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.
  3. Control-plane-related traffic receives the expected queue treatment under simulated load.
  4. Only traffic meeting the defined match receives the intended queue and packet loss priority.

Explanation

Correct Answer

B:

Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses. This checks the relevant result after configure supported egress shaping at the bottleneck and verify throughput and queue behavior.

Incorrect Answers

A:

“During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic” belongs to a separate Class of Service (CoS) issue: a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class. It does not explain the condition tested here.

C:

“Control-plane-related traffic receives the expected queue treatment under simulated load” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.

D:

“Only traffic meeting the defined match receives the intended queue and packet loss priority” belongs to a separate Class of Service (CoS) issue: an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.