Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 93

Question 920

The team believes it has resolved this Junos issue: A WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. Which observation best verifies the specific intended result?

  1. During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic.
  2. Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.
  3. Control-plane-related traffic receives the expected queue treatment under simulated load.
  4. Only traffic meeting the defined match receives the intended queue and packet loss priority.

Explanation

Correct Answer

B:

Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses. This checks the relevant result after configure supported egress shaping at the bottleneck and verify throughput and queue behavior.

Incorrect Answers

A:

“During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic” belongs to a separate Class of Service (CoS) issue: a business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class. It does not explain the condition tested here.

C:

“Control-plane-related traffic receives the expected queue treatment under simulated load” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.

D:

“Only traffic meeting the defined match receives the intended queue and packet loss priority” belongs to a separate Class of Service (CoS) issue: an application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It does not explain the condition tested here.

Question 921

A Junos enterprise team investigates this incident: A provider-facing policy stops honoring a route-tag community after a new import policy changes the attached communities. Which technical explanation most directly identifies the cause or design principle?

  1. Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it.
  2. Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints.
  3. BGP route selection first requires the BGP next hop to resolve through the appropriate routing table.
  4. BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops.

Explanation

Correct Answer

A:

Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it. The appropriate response is to inspect received communities and export policy terms, then attach a tested community match and reject rule.

Incorrect Answers

B:

“Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints” belongs to a separate Border Gateway Protocol (BGP) issue: a multihop eBGP peer uses loopback addresses but its session times out when directly connected assumptions remain. It does not explain the condition tested here.

C:

“BGP route selection first requires the BGP next hop to resolve through the appropriate routing table” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. It does not explain the condition tested here.

D:

“BGP next-hop resolution must use the appropriate address family; IPv4 routes do not automatically resolve IPv6 next hops” belongs to a separate Border Gateway Protocol (BGP) issue: an IPv6 BGP peer receives a route with an unreachable IPv6 next hop despite an otherwise valid inet6 unicast advertisement. It does not explain the condition tested here.

Question 922

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: Packets with two different drop precedence values are treated as equally discardable during congestion.

  1. Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy.
  2. Map every packet to the lowest loss priority regardless of its out-of-profile status.
  3. Let all untrusted clients self-select expedited forwarding marks without verification.
  4. Map the two packet categories to the intended PLP levels and verify drop-profile response.
  5. During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic.

Explanation

Correct Answers

D:

Map the two packet categories to the intended PLP levels and verify drop-profile response. This addresses the dependency that packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior.

E:

During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic. The specific steps required are to map the two packet categories to the intended PLP levels and verify drop-profile response.

Incorrect Answers

A:

“Assume a correct internal forwarding class guarantees outgoing DSCP is preserved without rewrite policy” is an unsafe response to a different problem: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It is not a valid fix here.

B:

“Map every packet to the lowest loss priority regardless of its out-of-profile status” does not address packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior.

C:

“Let all untrusted clients self-select expedited forwarding marks without verification” is an unsafe response to a different problem: a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice. It is not a valid fix here.

Question 923

Select THREE complementary corrective, verification, or preventive controls for this scenario: A stream uses asymmetric unicast routing; multicast forwarding fails intermittently although individual host routes work.

  1. Replace all multicast group filters with a broad permit because at least one approved stream failed.
  2. Require multicast forwarding to follow the receiver's shortest downstream path with no regard to source RPF.
  3. Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages.
  4. Compare source-route preference with actual multicast ingress and restore a consistent authorized upstream path.
  5. Test multicast source-path behavior under each failover case, not only unicast ping.
  6. RPF counters and expected (S,G) forwarding stabilize after the route change.

Explanation

Correct Answers

D:

Correction: An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic.

E:

Prevention of recurrence: An RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic.

F:

Confirmation: Compare source-route preference with actual multicast ingress and restore a consistent authorized upstream path.

Incorrect Answers

A:

“Replace all multicast group filters with a broad permit because at least one approved stream failed” is an unsafe response to a different problem: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It is not a valid fix here.

B:

“Require multicast forwarding to follow the receiver's shortest downstream path with no regard to source RPF” does not address an RPF check is tied to the selected source path, so asymmetric arrival can invalidate otherwise reachable multicast traffic.

C:

“Assume a working unicast BGP session automatically exchanges multicast MSDP source-active messages” is an unsafe response to a different problem: a multicast source is active in a different PIM domain but the local ASM RP never learns the source mapping. It is not a valid fix here.

Question 924

A Junos enterprise team investigates this incident: A captive portal requirement is applied to a headless barcode scanner that has no web browser to follow its redirect. Which technical explanation most directly identifies the cause or design principle?

  1. Supplicant absence is a distinct failure from an invalid credential or unreachable authentication server.
  2. MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication.
  3. 802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed.
  4. Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices.

Explanation

Correct Answer

D:

Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices. The appropriate response is to choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.

Incorrect Answers

A:

“Supplicant absence is a distinct failure from an invalid credential or unreachable authentication server” belongs to a separate Layer 2 Authentication and Access Control issue: a switch logs EAP timeout while the endpoint has no 802.1X supplicant, yet the operator rotates valid RADIUS passwords repeatedly. It does not explain the condition tested here.

B:

“MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication” belongs to a separate Layer 2 Authentication and Access Control issue: a printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy. It does not explain the condition tested here.

C:

“802.1X guest and fallback capabilities are platform and Junos variant specific; unsupported features must not be assumed” belongs to a separate Layer 2 Authentication and Access Control issue: an access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces. It does not explain the condition tested here.

Question 925

To prevent recurrence of this precise networking failure, which practice should be adopted? A second campus RP is deployed for availability but source-awareness synchronization is omitted where the design requires it.

  1. Run both allow and deny group tests against multicast policy whenever prefixes are revised.
  2. Check multicast and unicast topology alignment whenever routing paths or metrics change.
  3. Test RP failover and synchronization behavior before expanding Anycast RP.
  4. Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.

Explanation

Correct Answer

C:

Test RP failover and synchronization behavior before expanding Anycast RP. This guards against anycast RP aims for a stable RP address with multiple nodes; consistent source discovery and RP coordination are essential to the chosen architecture.

Incorrect Answers

A:

“Run both allow and deny group tests against multicast policy whenever prefixes are revised” belongs to a separate IP Multicast issue: an edge router uses a broad multicast filter that blocks valid collaboration groups alongside restricted lab streams. It does not explain the condition tested here.

B:

“Check multicast and unicast topology alignment whenever routing paths or metrics change” belongs to a separate IP Multicast issue: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It does not explain the condition tested here.

D:

“Document ASM/SSM selection and receiver-version prerequisites before multicast deployment” belongs to a separate IP Multicast issue: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It does not explain the condition tested here.

Question 926

Select THREE complementary corrective, verification, or preventive controls for this scenario: A business wants out-of-profile marked traffic to drop earlier than in-profile traffic within one forwarding class.

  1. Use an egress shaper at the wrong interface as a substitute for every ingress traffic-contract check.
  2. Map the two packet categories to the intended PLP levels and verify drop-profile response.
  3. Test marking, PLP assignment and drop policy together rather than checking only DSCP fields.
  4. During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic.
  5. Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration.
  6. Map every packet to the lowest loss priority regardless of its out-of-profile status.

Explanation

Correct Answers

B:

Correction: Packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior.

C:

Prevention of recurrence: Packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior.

D:

Confirmation: Map the two packet categories to the intended PLP levels and verify drop-profile response.

Incorrect Answers

A:

“Use an egress shaper at the wrong interface as a substitute for every ingress traffic-contract check” is an unsafe response to a different problem: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It is not a valid fix here.

E:

“Raise the permitted long-term traffic rate indefinitely rather than evaluating burst-size configuration” is an unsafe response to a different problem: a traffic policer drops small microbursts despite an acceptable average rate because its configured burst size is too tight. It is not a valid fix here.

F:

“Map every packet to the lowest loss priority regardless of its out-of-profile status” does not address packet loss priority differentiates drop susceptibility within a forwarding class and works with the configured queue/drop behavior.

Question 927

To prevent recurrence of this precise networking failure, which practice should be adopted? An uplink meets long-term bandwidth policy but legitimate short bursts exceed the token-bucket allowance.

  1. Test ingress classification separately from egress rewrite at every trust boundary.
  2. Keep a documented forwarding-class inventory and test default mappings after service changes.
  3. Establish congestion thresholds and monitor starvation as part of queue-priority design.
  4. Test both average-rate enforcement and microburst tolerance for new policer profiles.

Explanation

Correct Answer

D:

Test both average-rate enforcement and microburst tolerance for new policer profiles. This guards against policing behavior depends on both committed rate and burst tolerance; a badly chosen burst parameter can penalize valid traffic.

Incorrect Answers

A:

“Test ingress classification separately from egress rewrite at every trust boundary” belongs to a separate Class of Service (CoS) issue: a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. It does not explain the condition tested here.

B:

“Keep a documented forwarding-class inventory and test default mappings after service changes” belongs to a separate Class of Service (CoS) issue: an access router has many queue definitions but unexpected class-to-queue mappings cause control traffic to be delayed. It does not explain the condition tested here.

C:

“Establish congestion thresholds and monitor starvation as part of queue-priority design” belongs to a separate Class of Service (CoS) issue: two queues use the same scheduler priority, but the business expects one to always win during contention. It does not explain the condition tested here.

Question 928

A network change is required for the following specific situation: A financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. Which corrective action is most appropriate?

  1. Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform.
  2. Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.
  3. Inspect multicast RPF state and the routing table used for source resolution, then correct the underlay or allowed RPF selection.
  4. Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.

Explanation

Correct Answer

D:

Multicast administrative scoping must restrict eligible groups and outgoing boundaries; group addresses alone do not impose all policy. Verify this by checking that the specified groups remain within the approved scope while unrelated enterprise multicast flows continue.

Incorrect Answers

A:

“Select an appropriate SSM group range and verify source-specific IGMPv3/PIM signaling on the supported platform” belongs to a separate IP Multicast issue: a controlled one-source data feed requires group membership constrained by both source and group, not arbitrary senders. It does not explain the condition tested here.

B:

“Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports” belongs to a separate IP Multicast issue: a receiver port stops getting multicast because IGMP membership was not processed by the access switch after an interface move. It does not explain the condition tested here.

C:

“Inspect multicast RPF state and the routing table used for source resolution, then correct the underlay or allowed RPF selection” belongs to a separate IP Multicast issue: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It does not explain the condition tested here.

Question 929

A network change is required for the following specific situation: An access VLAN floods every multicast packet because IGMP snooping state was lost during migration. Which corrective action is most appropriate?

  1. Design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths.
  2. Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
  3. Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy.
  4. Inspect IGMP joins and snooping membership per VLAN and correct membership handling on the actual access ports.

Explanation

Correct Answer

D:

IGMP reports express receiver interest, and IGMP snooping uses that interest to constrain Layer 2 replication. Verify this by checking that subscribed receivers get the stream without unnecessary flood to ports that did not join.

Incorrect Answers

A:

“Design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths” belongs to a separate IP Multicast issue: a one-to-many lecture stream is configured as separate unicast connections and saturates a WAN link to a remote campus. It does not explain the condition tested here.

B:

“Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding” belongs to a separate IP Multicast issue: a laboratory's multicast test group leaks to the corporate backbone despite a requirement to keep it within the lab. It does not explain the condition tested here.

C:

“Identify the configured RPF table and verify the source route and next hop in that table before updating the multicast policy” belongs to a separate IP Multicast issue: a multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop. It does not explain the condition tested here.

Question 930

For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A campus OSPF interface is accidentally placed in area 0 while its neighbor advertises a nonbackbone area, preventing a Full adjacency.

  1. Change only router IDs while leaving the mismatched interface areas intact.
  2. Increase every external metric blindly without checking which path should win.
  3. Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy.
  4. OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements.
  5. Compare configured interface areas with the approved topology and put both interfaces in the intended matching area.

Explanation

Correct Answers

D:

OSPF neighbor state reaches Full and the expected area LSDB receives the neighbor advertisements. The specific steps required are to compare configured interface areas with the approved topology and put both interfaces in the intended matching area.

E:

Compare configured interface areas with the approved topology and put both interfaces in the intended matching area. This addresses the dependency that OSPF neighbors must agree on the area context to form adjacency on the common link.

Incorrect Answers

A:

“Change only router IDs while leaving the mismatched interface areas intact” does not address OSPF neighbors must agree on the area context to form adjacency on the common link.

B:

“Increase every external metric blindly without checking which path should win” is an unsafe response to a different problem: an OSPF policy update redistributes a route without an appropriate external metric, shifting traffic to a slow backup. It is not a valid fix here.

C:

“Record a successful IPv4 echo response as conclusive proof that OSPFv3 is healthy” is an unsafe response to a different problem: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It is not a valid fix here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.