100% Latest & Updated Microsoft AZ-700 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 410
An ExpressRoute circuit should provide redundant paths through two independent peering sessions. The architecture uses this design: Configure both primary and secondary BGP peering connections. Which configuration should the engineer apply to implement it?
- Enable active-active gateway operation and configure the two public peer endpoints
- Compare AS paths/local policies and advertised prefixes on both circuits
- Configure independent local network gateways/connections for both provider paths
- Set separate peer subnets and BGP parameters for the redundant paths
Explanation
Correct Answer
D:Set separate peer subnets and BGP parameters for the redundant paths is the operational configuration for configure both primary and secondary bgp peering connections. The acceptance test is to bring down one BGP peer and inspect remaining reachability.
Incorrect Answers
A:Enable active-active gateway operation and configure the two public peer endpoints is a concrete step for use a supported active-active vpn gateway topology. Here the selected design is configure both primary and secondary bgp peering connections, which instead requires set separate peer subnets and bgp parameters for the redundant paths.
B:Compare AS paths/local policies and advertised prefixes on both circuits is a concrete step for correct bgp route preference and path selection across hybrid links. Here the selected design is configure both primary and secondary bgp peering connections, which instead requires set separate peer subnets and bgp parameters for the redundant paths.
C:Configure independent local network gateways/connections for both provider paths is a concrete step for use redundant site-to-site vpn connections over separate isp endpoints. Here the selected design is configure both primary and secondary bgp peering connections, which instead requires set separate peer subnets and bgp parameters for the redundant paths.
Question 411
An ExpressRoute circuit should provide redundant paths through two independent peering sessions. After the team applies this change—set separate peer subnets and BGP parameters for the redundant paths—which validation best proves the intended result?
- Inspect local network gateway definitions against the router configuration
- Bring down one BGP peer and inspect remaining reachability
- Inspect circuit provider status and Azure private peering state
- Inspect client route table and test spoke private IP connectivity
Explanation
Correct Answer
B:Bring down one BGP peer and inspect remaining reachability directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether the redundant secondary BGP session was not configured.
Incorrect Answers
A:Inspect local network gateway definitions against the router configuration. This concerns being represented in azure. Instead, bring down one BGP peer and inspect remaining reachability.
C:Inspect circuit provider status and Azure private peering state. This concerns a private connectivity path from its network provider into microsoft cloud. Instead, bring down one BGP peer and inspect remaining reachability.
D:Inspect client route table and test spoke private IP connectivity. This is relevant when a vpn user can reach the hub VNet but cannot access a connected spoke. Instead, bring down one BGP peer and inspect remaining reachability.
Question 412
An ExpressRoute circuit should provide redundant paths through two independent peering sessions. During acceptance testing, single peering loss disconnects the entire private connection. Which underlying configuration problem best explains the symptom?
- The redundant secondary BGP session was not configured
- Only one functional tunnel path was configured
- The BGP peering session or route advertisement is absent
- The hub NVA integration or routing intent is not configured
Explanation
Correct Answer
A:The redundant secondary BGP session was not configured explains the observed failure: single peering loss disconnects the entire private connection. Correct the design by using configure both primary and secondary BGP peering connections, implemented through set separate peer subnets and BGP parameters for the redundant paths.
Incorrect Answers
B:Only one functional tunnel path was configured. This concerns two branch vpn devices should both be able to provide resilient connectivity to azure. Here, the redundant secondary BGP session was not configured.
C:The BGP peering session or route advertisement is absent. This concerns advertising and learn routes dynamically across a routed vpn. Here, the redundant secondary BGP session was not configured.
D:The hub NVA integration or routing intent is not configured. This concerns a third-party network virtual appliance inserted into virtual wan traffic paths. Here, the redundant secondary BGP session was not configured.
Question 413
A customer needs an Azure VNet gateway that sends applicable traffic directly over the ExpressRoute data path for better throughput. Which Azure networking design most directly satisfies this requirement?
- Update the corresponding local network gateway public IP endpoint
- Revoke the contractor certificate using the supported VPN certificate revocation process
- Consider ExpressRoute FastPath on supported gateway and circuit combinations
- Evaluate ExpressRoute Premium and Global Reach coverage requirements
Explanation
Correct Answer
C:Consider ExpressRoute FastPath on supported gateway and circuit combinations addresses the topology, access or delivery requirement in the scenario. Apply it by use supported gateway SKU and enable FastPath on the eligible connection; confirm by inspect FastPath configuration and measure the supported VM data path.
Incorrect Answers
A:Update the corresponding local network gateway public IP endpoint. This is relevant when a company is moving its site-to-site tunnel to a different on-premises public address. Here, consider ExpressRoute FastPath on supported gateway and circuit combinations.
B:Revoke the contractor certificate using the supported VPN certificate revocation process. This concerns revoking one contractor. Here, consider ExpressRoute FastPath on supported gateway and circuit combinations.
D:Evaluate ExpressRoute Premium and Global Reach coverage requirements. This concerns expressRoute connectivity between distant geopolitical regions. Here, consider ExpressRoute FastPath on supported gateway and circuit combinations.
Question 414
A customer needs an Azure VNet gateway that sends applicable traffic directly over the ExpressRoute data path for better throughput. The architecture uses this design: Consider ExpressRoute FastPath on supported gateway and circuit combinations. Which configuration should the engineer apply to implement it?
- Add a correctly named GatewaySubnet of supported prefix size before deployment
- Correct tenant/issuer/audience fields in the gateway and client settings
- Use supported gateway SKU and enable FastPath on the eligible connection
- Inspect service key status and provider/peering/connection health in one workflow
Explanation
Correct Answer
C:Use supported gateway SKU and enable FastPath on the eligible connection is the operational configuration for consider expressroute fastpath on supported gateway and circuit combinations. The acceptance test is to inspect FastPath configuration and measure the supported VM data path.
Incorrect Answers
A:Add a correctly named GatewaySubnet of supported prefix size before deployment is a concrete step for create a valid dedicated gatewaysubnet inside the target vnet. Here the selected design is consider expressroute fastpath on supported gateway and circuit combinations, which instead requires use supported gateway sku and enable fastpath on the eligible connection.
B:Correct tenant/issuer/audience fields in the gateway and client settings is a concrete step for validate microsoft entra application registration and audience alignment. Here the selected design is consider expressroute fastpath on supported gateway and circuit combinations, which instead requires use supported gateway sku and enable fastpath on the eligible connection.
D:Inspect service key status and provider/peering/connection health in one workflow is a concrete step for compare provider provisioning, azure circuit state and bgp peering diagnostics. Here the selected design is consider expressroute fastpath on supported gateway and circuit combinations, which instead requires use supported gateway sku and enable fastpath on the eligible connection.
Question 415
A customer needs an Azure VNet gateway that sends applicable traffic directly over the ExpressRoute data path for better throughput. After the team applies this change—use supported gateway SKU and enable FastPath on the eligible connection—which validation best proves the intended result?
- Inspect FastPath configuration and measure the supported VM data path
- Inspect effective hub routes and simulate allowed and disallowed paths
- Inspect negotiated selectors and confirm required prefixes pass
- Inspect port link health and circuit provisioning for each circuit
Explanation
Correct Answer
A:Inspect FastPath configuration and measure the supported VM data path directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether the FastPath feature is disabled or incompatible.
Incorrect Answers
B:Inspect effective hub routes and simulate allowed and disallowed paths. This concerns controlled inter-hub route propagation. Instead, inspect FastPath configuration and measure the supported VM data path.
C:Inspect negotiated selectors and confirm required prefixes pass. This concerns a legacy on-premises IPSEC device only supports policy-based traffic selectors. Instead, inspect FastPath configuration and measure the supported VM data path.
D:Inspect port link health and circuit provisioning for each circuit. This concerns a high-throughput dedicated connection to microsoft without a standard provider-managed circuit. Instead, inspect FastPath configuration and measure the supported VM data path.
Question 416
A customer needs an Azure VNet gateway that sends applicable traffic directly over the ExpressRoute data path for better throughput. During acceptance testing, traffic always traverses the ExpressRoute gateway dataplane despite FastPath plan. Which underlying configuration problem best explains the symptom?
- The FastPath feature is disabled or incompatible
- The gateway cannot reach the RADIUS endpoint or the shared secret differs
- The root certificate trust or client key chain is incorrect
- The selected VPN Gateway SKU was undersized or incompatible
Explanation
Correct Answer
A:The FastPath feature is disabled or incompatible explains the observed failure: traffic always traverses the ExpressRoute gateway dataplane despite FastPath plan. Correct the design by using consider ExpressRoute FastPath on supported gateway and circuit combinations, implemented through use supported gateway SKU and enable FastPath on the eligible connection.
Incorrect Answers
B:The gateway cannot reach the RADIUS endpoint or the shared secret differs. This concerns a central radius service to validate users. Here, the FastPath feature is disabled or incompatible.
C:The root certificate trust or client key chain is incorrect. This concerns device certificates from a private pki. Here, the FastPath feature is disabled or incompatible.
D:The selected VPN Gateway SKU was undersized or incompatible. This concerns selecting a vpn gateway sku for expected throughput and resiliency. Here, the FastPath feature is disabled or incompatible.
Question 417
The finance team needs a private circuit but also requires cryptographic encryption in transit. Which Azure networking design most directly satisfies this requirement?
- Add an encryption overlay where supported instead of assuming ExpressRoute is encrypted
- Configure Azure private peering on the ExpressRoute circuit
- Add an ExpressRoute gateway and circuit connection to an eligible virtual hub
- Configure RADIUS authentication for the supported P2S gateway setup
Explanation
Correct Answer
A:Add an encryption overlay where supported instead of assuming ExpressRoute is encrypted addresses the topology, access or delivery requirement in the scenario. Apply it by deploy a supported IPsec or MACsec approach according to port and service capability; confirm by validate tunnel security association or MACsec operational state.
Incorrect Answers
B:Configure Azure private peering on the ExpressRoute circuit. This concerns exchange private Azure VNet routes over ExpressRoute. Instead, add an encryption overlay where supported instead of assuming ExpressRoute is encrypted.
C:Add an ExpressRoute gateway and circuit connection to an eligible virtual hub. This concerns private ExpressRoute access to its global Virtual WAN topology. Instead, add an encryption overlay where supported instead of assuming ExpressRoute is encrypted.
D:Configure RADIUS authentication for the supported P2S gateway setup. This concerns a central RADIUS service to validate users. Instead, add an encryption overlay where supported instead of assuming ExpressRoute is encrypted.
Question 418
The finance team needs a private circuit but also requires cryptographic encryption in transit. The architecture uses this design: Add an encryption overlay where supported instead of assuming ExpressRoute is encrypted. Which configuration should the engineer apply to implement it?
- Set the RADIUS server IP/secret and ensure the gateway can reach the service
- Use supported gateway SKU and enable FastPath on the eligible connection
- Set matching encryption, integrity, DH and PFS parameters where supported
- Deploy a supported IPsec or MACsec approach according to port and service capability
Explanation
Correct Answer
D:Deploy a supported IPsec or MACsec approach according to port and service capability is the operational configuration for add an encryption overlay where supported instead of assuming expressroute is encrypted. The acceptance test is to validate tunnel security association or MACsec operational state.
Incorrect Answers
A:Set the RADIUS server IP/secret and ensure the gateway can reach the service is a concrete step for configure radius authentication for the supported p2s gateway setup. Here the selected design is add an encryption overlay where supported instead of assuming expressroute is encrypted, which instead requires deploy a supported ipsec or macsec approach according to port and service capability.
B:Use supported gateway SKU and enable FastPath on the eligible connection is a concrete step for consider expressroute fastpath on supported gateway and circuit combinations. Here the selected design is add an encryption overlay where supported instead of assuming expressroute is encrypted, which instead requires deploy a supported ipsec or macsec approach according to port and service capability.
C:Set matching encryption, integrity, DH and PFS parameters where supported is a concrete step for align both ends on a supported ike/ipsec policy. Here the selected design is add an encryption overlay where supported instead of assuming expressroute is encrypted, which instead requires deploy a supported ipsec or macsec approach according to port and service capability.
Question 419
The finance team needs a private circuit but also requires cryptographic encryption in transit. After the team applies this change—deploy a supported IPsec or MACsec approach according to port and service capability—which validation best proves the intended result?
- Verify Established state on both private BGP sessions
- Compare measured tunnel throughput and configured scale units
- Validate tunnel security association or MACsec operational state
- Inspect new IKE association source and confirm the connection becomes Connected
Explanation
Correct Answer
C:Validate tunnel security association or MACsec operational state directly checks whether the intended outcome occurs, not merely whether a resource exists. If the check fails, investigate whether private ExpressRoute transport alone does not provide encryption.
Incorrect Answers
A:Verify Established state on both private BGP sessions. This concerns BGP routing over expressroute fails after the customer changes its asn. Here, validate tunnel security association or MACsec operational state.
B:Compare measured tunnel throughput and configured scale units. This concerns branch bandwidth requirements exceed the default hub vpn capacity. Here, validate tunnel security association or MACsec operational state.
D:Inspect new IKE association source and confirm the connection becomes Connected. This is relevant when a company is moving its site-to-site tunnel to a different on-premises public address. Here, validate tunnel security association or MACsec operational state.
Question 420
The finance team needs a private circuit but also requires cryptographic encryption in transit. During acceptance testing, traffic remains unencrypted although it is on a private circuit. Which underlying configuration problem best explains the symptom?
- The IPsec traffic selector configuration does not include them
- GatewaySubnet naming or sizing does not meet requirements
- Private ExpressRoute transport alone does not provide encryption
- Entra issuer or audience configuration does not match the client token
Explanation
Correct Answer
C:Private ExpressRoute transport alone does not provide encryption explains the observed failure: traffic remains unencrypted although it is on a private circuit. Correct the design by using add an encryption overlay where supported instead of assuming ExpressRoute is encrypted, implemented through deploy a supported IPsec or MACsec approach according to port and service capability.
Incorrect Answers
A:The IPsec traffic selector configuration does not include them. This concerns a legacy on-premises IPSEC device only supports policy-based traffic selectors. Here, private ExpressRoute transport alone does not provide encryption.
B:GatewaySubnet naming or sizing does not meet requirements. This is relevant when a vpn gateway is provisioned but its resource cannot be placed in the intended VNet. Here, private ExpressRoute transport alone does not provide encryption.
D:Entra issuer or audience configuration does not match the client token. This is relevant when a p2s gateway is configured but a user receives invalid-signature token errors. Here, private ExpressRoute transport alone does not provide encryption.
Designing and Implementing Microsoft Azure Networking Solutions (AZ-700) Practice Tests