100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 220
To prevent recurrence of this precise networking failure, which practice should be adopted? OSPFv3 peering comes up but the desired IPv6 loopback is not in the routing database after a rollout.
- Validate per-interface OSPF area assignments from an approved topology matrix before commit.
- Document expected external metrics and run primary/backup failover tests during policy changes.
- Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance.
- Specify preferred OSPF DR candidates on shared transit segments and account for non-preemptive elections.
Explanation
Correct Answer
C:Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance. This guards against an established OSPFv3 neighbor does not prove every desired IPv6 interface prefix is included in the protocol topology.
Incorrect Answers
A:“Validate per-interface OSPF area assignments from an approved topology matrix before commit” belongs to a separate Interior Gateway Protocols (IGPs) issue: a campus OSPF interface is accidentally placed in area 0 while its neighbor advertises a nonbackbone area, preventing a Full adjacency. It does not explain the condition tested here.
B:“Document expected external metrics and run primary/backup failover tests during policy changes” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.
D:“Specify preferred OSPF DR candidates on shared transit segments and account for non-preemptive elections” belongs to a separate Interior Gateway Protocols (IGPs) issue: an aggregation broadcast VLAN has a DR/BDR placement that conflicts with the approved design after a maintenance reboot. It does not explain the condition tested here.
Question 221
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: Two authentication methods are enabled on a shared switch port but fallback ordering bypasses a successful 802.1X result.
- Authenticated corporate devices use strong EAP policies while designated legacy endpoints use restricted fallback.
- Rotate every user's password without checking whether the endpoint sent an EAP response at all.
- Allow the weakest matching authentication method to grant full access regardless of prior EAP outcomes.
- Mark every unknown MAC as trusted and give it unrestricted data-VLAN access.
- Inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior.
Explanation
Correct Answers
A:Authenticated corporate devices use strong EAP policies while designated legacy endpoints use restricted fallback. The specific steps required are to inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior.
E:Inspect supported method sequencing and enforce the approved 802.1X-first and MAC-exception behavior. This addresses the dependency that authentication-method precedence and session state can affect which effective authorization takes hold.
Incorrect Answers
B:“Rotate every user's password without checking whether the endpoint sent an EAP response at all” is an unsafe response to a different problem: a switch logs EAP timeout while the endpoint has no 802.1X supplicant, yet the operator rotates valid RADIUS passwords repeatedly. It is not a valid fix here.
C:“Allow the weakest matching authentication method to grant full access regardless of prior EAP outcomes” does not address authentication-method precedence and session state can affect which effective authorization takes hold.
D:“Mark every unknown MAC as trusted and give it unrestricted data-VLAN access” is an unsafe response to a different problem: a non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. It is not a valid fix here.
Question 222
Which suggested shortcut would be especially unsafe for this exact situation? A switch assigns equal PoE power priority to every port and disconnects an emergency phone before low-priority signage during a power shortage.
- Review LLDP-MED state and phone compliance during access-switch template audits.
- Synchronize switchport moves with maintained emergency location records.
- Allocate identical priority to all PoE consumers and assume emergency devices receive preferential power.
- Include end-to-end marking tests when deploying voice VLANs and new phone models.
Explanation
Correct Answer
C:The tempting alternative fails because PoE priority is a tool for allocating scarce power among endpoints when the chassis budget is constrained. The supported action is to set supported higher PoE priority for critical voice endpoints and validate the failure budget.
Incorrect Answers
A:That prevention measure relates to a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature.; it is not the unsafe shortcut described here.
B:That prevention measure relates to an IP phone uses the wrong location information for emergency response after a switch move.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a handset follows LLDP-MED voice VLAN advertisement but sends SIP media with the wrong priority marking for the campus QoS design.; it is not the unsafe shortcut described here.
Question 223
A network change is required for the following specific situation: A BGP export policy advertises a prefix that exists only as an inactive local candidate, despite an expectation of default active-only behavior. Which corrective action is most appropriate?
- Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail.
- Inspect active-route selection and the advertise-inactive configuration; keep it only if the external requirement justifies it.
- Inspect received communities and export policy terms, then attach a tested community match and reject rule.
- Check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks.
Explanation
Correct Answer
B:Junos normally exports active routes; advertise-inactive can expose a best BGP candidate that lost to another protocol. Verify this by checking that the advertised set matches the documented inactive-BGP exception without changing local forwarding selection.
Incorrect Answers
A:“Restore permitted next-hop reachability via IGP or adjust next-hop policy where appropriate; recheck route detail” belongs to a separate Border Gateway Protocol (BGP) issue: an iBGP route is received from a reflector but hidden because its third-party next hop is unreachable in inet.0. It does not explain the condition tested here.
C:“Inspect received communities and export policy terms, then attach a tested community match and reject rule” belongs to a separate Border Gateway Protocol (BGP) issue: a network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. It does not explain the condition tested here.
D:“Check the advertised AS sequence and correct the peering or routing design instead of bypassing loop checks” belongs to a separate Border Gateway Protocol (BGP) issue: a carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path. It does not explain the condition tested here.
Question 224
The team believes it has resolved this Junos issue: A high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. Which observation best verifies the specific intended result?
- The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN.
- Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface.
- Tagged voice packets retain the intended service class through the access and aggregation paths.
- The phone receives stable negotiated power and the chassis stays within its supported budget under peak load.
Explanation
Correct Answer
D:The phone receives stable negotiated power and the chassis stays within its supported budget under peak load. This checks the relevant result after check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power.
Incorrect Answers
A:“The phone receives voice service on its tagged VLAN and the PC remains on its separate data VLAN” belongs to a separate IP Telephony Features issue: a phone-with-PC desk deployment lets the PC reach data services while the tagged voice stream is dropped by VLAN membership. It does not explain the condition tested here.
B:“Packet and operational views show the required LLDP-MED telephony TLVs at the correct interface” belongs to a separate IP Telephony Features issue: a powered endpoint detects a Junos switch but fails to negotiate voice prioritization because only ordinary LLDP is enabled. It does not explain the condition tested here.
C:“Tagged voice packets retain the intended service class through the access and aggregation paths” belongs to a separate IP Telephony Features issue: a voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. It does not explain the condition tested here.
Question 225
A network change is required for the following specific situation: Two iBGP exits offer equal reachable routes but the one with higher LOCAL_PREF is not the egress an operator expected. Which corrective action is most appropriate?
- Inspect active-route selection and the advertise-inactive configuration; keep it only if the external requirement justifies it.
- Verify endpoint reachability and configure appropriate multihop session parameters and security controls.
- Inspect per-route local preferences and import policy; set the intended exit's LOCAL_PREF consistently.
- Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration.
Explanation
Correct Answer
C:BGP typically prefers a larger LOCAL_PREF among otherwise eligible candidates before later path-selection tie breakers. Verify this by checking that the selected BGP route reflects the intended higher LOCAL_PREF, and traceroute follows the approved exit.
Incorrect Answers
A:“Inspect active-route selection and the advertise-inactive configuration; keep it only if the external requirement justifies it” belongs to a separate Border Gateway Protocol (BGP) issue: an engineer adds advertise-inactive and downstream peers begin receiving a BGP route that loses to an OSPF route locally. It does not explain the condition tested here.
B:“Verify endpoint reachability and configure appropriate multihop session parameters and security controls” belongs to a separate Border Gateway Protocol (BGP) issue: a transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated. It does not explain the condition tested here.
D:“Inspect reflector/client relationships and cluster behavior, then correct the intended route-reflector configuration” belongs to a separate Border Gateway Protocol (BGP) issue: a route-reflector topology loses an iBGP-advertised prefix because clients are not configured under the intended reflector cluster. It does not explain the condition tested here.
Question 226
Select THREE complementary corrective, verification, or preventive controls for this scenario: A remote prefix appears in incoming BGP updates yet never becomes active after a new route policy was applied.
- Keep restarting the established BGP session without evaluating import-policy filtering.
- The desired received prefix is accepted and active while intentionally blocked prefixes stay rejected.
- Assume successful inet IPv4 routes imply that IPv6 NLRI is already negotiated.
- Inspect hidden-route reason, incoming attributes and import-policy decisions, then correct the authorized match.
- Add a second BGP neighbor and assume the forwarding table automatically load-balances every route.
- Include show route hidden and policy term hit checks in BGP troubleshooting playbooks.
Explanation
Correct Answers
B:Confirmation: Inspect hidden-route reason, incoming attributes and import-policy decisions, then correct the authorized match.
D:Correction: A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session.
F:Prevention of recurrence: A BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session.
Incorrect Answers
A:“Keep restarting the established BGP session without evaluating import-policy filtering” does not address a BGP route rejected or hidden by import policy can be absent from active forwarding despite a healthy peer session.
C:“Assume successful inet IPv4 routes imply that IPv6 NLRI is already negotiated” is an unsafe response to a different problem: BGP peers exchange IPv4 NLRI correctly but a planned IPv6 customer route never appears in inet6.0. It is not a valid fix here.
E:“Add a second BGP neighbor and assume the forwarding table automatically load-balances every route” is an unsafe response to a different problem: equal candidate BGP routes are visible but no multipath forwarding entry is installed because eligibility or policy differs. It is not a valid fix here.
Question 227
The team believes it has resolved this Junos issue: An ingress classification filter for one terminal type inadvertently redirects other hosts using the same uplink. Which observation best verifies the specific intended result?
- The redundant topology converges without sustained broadcast loops during link-failure testing.
- The customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology.
- Only the intended endpoint class is moved while nonmatching hosts retain correct access.
- The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion.
Explanation
Correct Answer
C:Only the intended endpoint class is moved while nonmatching hosts retain correct access. This checks the relevant result after narrow the match to approved selectors and compare affected packet counters and VLAN assignment.
Incorrect Answers
A:“The redundant topology converges without sustained broadcast loops during link-failure testing” belongs to a separate Ethernet Switching and Spanning Tree issue: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It does not explain the condition tested here.
B:“The customer control protocol reaches the far endpoint without altering the provider's own spanning-tree topology” belongs to a separate Ethernet Switching and Spanning Tree issue: an 802.1Q trunk carries customer data through a provider Ethernet segment but fails to forward the required spanning-tree control frames transparently. It does not explain the condition tested here.
D:“The required VLAN groups follow their designated MSTI paths without per-VLAN instance explosion” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.
Question 228
A network change is required for the following specific situation: A redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. Which corrective action is most appropriate?
- Map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated.
- Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
- Inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation.
- Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.
Explanation
Correct Answer
B:Spanning-tree edge-port assumptions are intended for non-switching endpoints, not redundant bridging connections. Verify this by checking that the redundant topology converges without sustained broadcast loops during link-failure testing.
Incorrect Answers
A:“Map the trusted endpoints to the proper community secondary VLAN and keep other groups segregated” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch rollout splits a team that should communicate within one PVLAN community, while protecting it from another community. It does not explain the condition tested here.
C:“Inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation” belongs to a separate Ethernet Switching and Spanning Tree issue: a Q-in-Q service works across transport but the far-end access handoff presents unexpected double tags. It does not explain the condition tested here.
D:“Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity” belongs to a separate Ethernet Switching and Spanning Tree issue: a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. It does not explain the condition tested here.
Question 229
A Junos enterprise team investigates this incident: A security function needs to classify a subset of traffic by source and destination criteria rather than trusted external markings. Which technical explanation most directly identifies the cause or design principle?
- Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification.
- Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings.
- A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress.
- Scheduler priority and bandwidth allocation affect queuing service but must balance fairness and starvation concerns.
Explanation
Correct Answer
A:Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification. The appropriate response is to use a permitted firewall or multifield classifier matching the approved traffic fields and assign its forwarding class.
Incorrect Answers
B:“Junos egress rewrite rules map internal forwarding class and PLP back into supported packet header markings” belongs to a separate Class of Service (CoS) issue: a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. It does not explain the condition tested here.
C:“A policer enforces traffic rate or burst limits and can discard or mark out-of-profile input; shaping buffers traffic for paced egress” belongs to a separate Class of Service (CoS) issue: a guest network should be rate-limited at ingress, but engineers configure only an egress shaper on the uplink. It does not explain the condition tested here.
D:“Scheduler priority and bandwidth allocation affect queuing service but must balance fairness and starvation concerns” belongs to a separate Class of Service (CoS) issue: a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. It does not explain the condition tested here.
Question 230
Which suggested shortcut would be especially unsafe for this exact situation? A voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification.
- Review LLDP-MED state and phone compliance during access-switch template audits.
- Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
- Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN.
- Synchronize switchport moves with maintained emergency location records.
Explanation
Correct Answer
C:The tempting alternative fails because voice VLAN placement and CoS marking are related but separate; correct VLAN tagging does not guarantee priority handling. The supported action is to verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
Incorrect Answers
A:That prevention measure relates to a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a campus changes a telephone port but LLDP-MED location data remains mapped to an old floor.; it is not the unsafe shortcut described here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests