Juniper JN0-650 Exam Dumps, Practice Test Questions

100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!

Juniper JN0-650  Premium File
$54.99
$49.99

JN0-650 Premium File

  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates

JN0-650 Premium File

Juniper JN0-650  Premium File
  • Premium File: 107 Questions & Answers. Last update: Nov 7, 2026
  • Latest Questions
  • 100% Accurate Answers
  • Fast Exam Updates
$54.99
$49.99

Juniper JN0-650 Practice Test 25

Question 240

A network change is required for the following specific situation: A printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy. Which corrective action is most appropriate?

  1. Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.
  2. Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
  3. Check authentication result classification and map the rejected user to an appropriate deny or reject response.
  4. Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.

Explanation

Correct Answer

A:

MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication. Verify this by checking that only the inventoried device has the expected limited connectivity; rogue or unknown hardware is denied.

Incorrect Answers

B:

“Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration” belongs to a separate Layer 2 Authentication and Access Control issue: a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend. It does not explain the condition tested here.

C:

“Check authentication result classification and map the rejected user to an appropriate deny or reject response” belongs to a separate Layer 2 Authentication and Access Control issue: a credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants. It does not explain the condition tested here.

D:

“Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods” belongs to a separate Layer 2 Authentication and Access Control issue: an access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces. It does not explain the condition tested here.

Question 241

Which suggested shortcut would be especially unsafe for this exact situation? A core-router replacement leaves an OSPF adjacency stuck exchanging database descriptions, while the two ends have different Layer 3 MTUs.

  1. Disable the MTU check indefinitely without identifying why adjacent links differ.
  2. Keep IPv4 and IPv6 routing verification separate for dual-stack maintenance.
  3. Validate active logical-interface mappings and IPv6 adjacency as part of change acceptance.
  4. Include a checklist of advertised IPv6 service and loopback addresses in OSPFv3 acceptance.

Explanation

Correct Answer

A:

The tempting alternative fails because OSPF database-description exchange can stall when adjacent interfaces disagree on MTU even though basic Hello connectivity exists. The supported action is to compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints.

Incorrect Answers

B:

That prevention measure relates to an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to an IPv6-only branch has OSPFv3 Hellos on the wrong logical unit after interface renumbering, so no IPv6 routes appear.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to OSPFv3 peering comes up but the desired IPv6 loopback is not in the routing database after a rollout.; it is not the unsafe shortcut described here.

Question 242

A Junos enterprise team investigates this incident: A noninteractive sensor is trapped in captive-portal onboarding because operators selected browser authentication for all endpoints. Which technical explanation most directly identifies the cause or design principle?

  1. MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication.
  2. Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices.
  3. Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary.
  4. Supplicant absence is a distinct failure from an invalid credential or unreachable authentication server.

Explanation

Correct Answer

B:

Captive portals presume interactive browser capabilities, making them unsuitable as the sole access method for headless devices. The appropriate response is to choose a documented compatible nonbrowser method such as supported MAC RADIUS under narrow access controls.

Incorrect Answers

A:

“MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication” belongs to a separate Layer 2 Authentication and Access Control issue: a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale. It does not explain the condition tested here.

C:

“Authentication success and postauthentication VLAN/policy assignment are separate stages whose feature support may vary” belongs to a separate Layer 2 Authentication and Access Control issue: a switch receives successful RADIUS Access-Accept but the user still lands in an unexpected VLAN because the dynamic assignment is not supported on that platform. It does not explain the condition tested here.

D:

“Supplicant absence is a distinct failure from an invalid credential or unreachable authentication server” belongs to a separate Layer 2 Authentication and Access Control issue: a switch logs EAP timeout while the endpoint has no 802.1X supplicant, yet the operator rotates valid RADIUS passwords repeatedly. It does not explain the condition tested here.

Question 243

The team believes it has resolved this Junos issue: A new endpoint MAC is learned at a remote VTEP but never reaches the receiving leaf's EVPN control-plane table. Which observation best verifies the specific intended result?

  1. The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding.
  2. The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended.
  3. BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates.
  4. Tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated.

Explanation

Correct Answer

A:

The current MAC location is learned and traffic reaches the moved endpoint without persistent old-VTEP forwarding. This checks the relevant result after check relevant BGP EVPN Type 2 advertisements, MAC mobility updates and import policy for the affected bridge domain.

Incorrect Answers

B:

“The remote VTEP becomes reachable and encapsulated packets cross the fabric as intended” belongs to a separate EVPN issue: a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback. It does not explain the condition tested here.

C:

“BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates” belongs to a separate EVPN issue: an EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. It does not explain the condition tested here.

D:

“Tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated” belongs to a separate EVPN issue: a campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. It does not explain the condition tested here.

Question 244

To prevent recurrence of this precise networking failure, which practice should be adopted? An ABR stops advertising a branch prefix into the backbone after an OSPF area-range summary is configured incorrectly.

  1. Test one allowed and one forbidden route against each export policy term before deployment.
  2. Run prefix-boundary tests before enabling area aggregation on an ABR.
  3. Document expected external metrics and run primary/backup failover tests during policy changes.
  4. Use named prefix lists and regression tests for approved and denied redistribution cases.

Explanation

Correct Answer

B:

Run prefix-boundary tests before enabling area aggregation on an ABR. This guards against area summarization scope must correctly cover the intended component networks; the wrong range can suppress or misrepresent reachability.

Incorrect Answers

A:

“Test one allowed and one forbidden route against each export policy term before deployment” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch default-route injection stops after a policy matches OSPF-learned routes instead of the intended local static. It does not explain the condition tested here.

C:

“Document expected external metrics and run primary/backup failover tests during policy changes” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch receives two external paths with different metric-type assumptions after a policy change and prefers the wrong exit. It does not explain the condition tested here.

D:

“Use named prefix lists and regression tests for approved and denied redistribution cases” belongs to a separate Interior Gateway Protocols (IGPs) issue: a redistribution policy injects every static route into OSPF, including a maintenance-only prefix that should stay local. It does not explain the condition tested here.

Question 245

A network change is required for the following specific situation: A trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. Which corrective action is most appropriate?

  1. Check group-to-RP mapping and RP reachability, then repair the RP discovery or explicit mapping.
  2. Design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths.
  3. Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding.
  4. Inspect MSDP peer state and source-active information, then configure the permitted peer relationships.

Explanation

Correct Answer

B:

IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream. Verify this by checking that backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream.

Incorrect Answers

A:

“Check group-to-RP mapping and RP reachability, then repair the RP discovery or explicit mapping” belongs to a separate IP Multicast issue: a PIM sparse-mode receiver has an IGMP join but no multicast traffic because its upstream router cannot resolve the rendezvous point. It does not explain the condition tested here.

C:

“Configure group-aware multicast routing policy and boundary filters at intended exits, then verify forwarding” belongs to a separate IP Multicast issue: a financial multicast feed intended for one campus crosses the WAN because no boundary controls are configured. It does not explain the condition tested here.

D:

“Inspect MSDP peer state and source-active information, then configure the permitted peer relationships” belongs to a separate IP Multicast issue: a receiver domain requires discovery of sources known behind another RP, yet inter-RP source information exchange is absent. It does not explain the condition tested here.

Question 246

Which suggested shortcut would be especially unsafe for this exact situation? A router prefers a longer AS path when a higher LOCAL_PREF makes that route win, surprising the transit team.

  1. Include inet6-specific next-hop verification in dual-stack BGP peer checklists.
  2. Assume the shortest AS path must win regardless of any LOCAL_PREF difference.
  3. Audit prefix and mask-length boundaries with positive and negative routing-policy tests.
  4. Validate all required BGP address families during dual-stack peer commissioning.

Explanation

Correct Answer

B:

The tempting alternative fails because for eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner. The supported action is to examine both attributes in the received route detail and update the explicit routing policy rather than guessing.

Incorrect Answers

A:

That prevention measure relates to an IPv6 BGP peer receives a route with an unreachable IPv6 next hop despite an otherwise valid inet6 unicast advertisement.; it is not the unsafe shortcut described here.

C:

That prevention measure relates to a prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a campus router's BGP IPv6 session is Established yet peers advertise only inet unicast family routes.; it is not the unsafe shortcut described here.

Question 247

Which suggested shortcut would be especially unsafe for this exact situation? A Q-in-Q service works across transport but the far-end access handoff presents unexpected double tags.

  1. Test gateway and approved shared-service access alongside lateral isolation in PVLAN reviews.
  2. Maintain representative match and nonmatch tests for filter-based VLAN policies.
  3. Assume every endpoint supports stacked 802.1Q tags even when the customer ordered a single-tagged handoff.
  4. Audit edge classifications and apply appropriate BPDU protection on true client-facing ports.

Explanation

Correct Answer

C:

The tempting alternative fails because Q-in-Q requires deliberate tagging and untagging at service boundaries, with customer tags retained according to the handoff contract. The supported action is to inspect the ingress/egress tag-processing configuration and correct the service handoff encapsulation.

Incorrect Answers

A:

That prevention measure relates to a building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked.; it is not the unsafe shortcut described here.

B:

That prevention measure relates to a campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them.; it is not the unsafe shortcut described here.

D:

That prevention measure relates to a campus mistakenly enables edge behavior on a switch-to-switch trunk and a loop appears when a backup link activates.; it is not the unsafe shortcut described here.

Question 248

The team believes it has resolved this Junos issue: A campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them. Which observation best verifies the specific intended result?

  1. Matching test traffic enters the quarantine VLAN while ordinary traffic stays in the expected VLAN.
  2. The VLAN registration propagates to the intended downstream trunk and reaches its member ports.
  3. Root and forwarding roles match the approved topology under normal and failover conditions.
  4. Both switches show compatible region membership and intended instance root/port roles.

Explanation

Correct Answer

A:

Matching test traffic enters the quarantine VLAN while ordinary traffic stays in the expected VLAN. This checks the relevant result after inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.

Incorrect Answers

B:

“The VLAN registration propagates to the intended downstream trunk and reaches its member ports” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared uplink carries dynamically registered VLANs until one device has MVRP disabled during an upgrade. It does not explain the condition tested here.

C:

“Root and forwarding roles match the approved topology under normal and failover conditions” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet. It does not explain the condition tested here.

D:

“Both switches show compatible region membership and intended instance root/port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: an uplink becomes a region boundary unexpectedly after an administrator changes an MSTP configuration name on only one switch. It does not explain the condition tested here.

Question 249

A Junos enterprise team investigates this incident: An OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. Which technical explanation most directly identifies the cause or design principle?

  1. IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges.
  2. OSPF neighbors require compatible Hello and dead interval settings on the shared interface.
  3. Making a link passive suppresses OSPF adjacency formation even when its prefix remains eligible for advertisement.
  4. Unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability.

Explanation

Correct Answer

A:

IPv4 packet reachability does not independently validate OSPFv3's IPv6 link-local neighbor exchanges. The appropriate response is to check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.

Incorrect Answers

B:

“OSPF neighbors require compatible Hello and dead interval settings on the shared interface” belongs to a separate Interior Gateway Protocols (IGPs) issue: an access-area adjacency drops after one device is changed to shorter OSPF Hello timers but its peer keeps prior settings. It does not explain the condition tested here.

C:

“Making a link passive suppresses OSPF adjacency formation even when its prefix remains eligible for advertisement” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF neighbor remains Down because the routed transit interface was left passive after a site template rollout. It does not explain the condition tested here.

D:

“Unrestricted OSPF export policy can originate unintended external routes, changing enterprise reachability” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR starts leaking a management static route into the enterprise IGP after a permissive export term was introduced. It does not explain the condition tested here.

Question 250

To prevent recurrence of this precise networking failure, which practice should be adopted? A phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature.

  1. Include end-to-end marking tests when deploying voice VLANs and new phone models.
  2. Review LLDP-MED state and phone compliance during access-switch template audits.
  3. Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
  4. Test both tagged phone frames and untagged PC frames during phone-port commissioning.

Explanation

Correct Answer

B:

Review LLDP-MED state and phone compliance during access-switch template audits. This guards against base LLDP discovery and LLDP-MED telephony advertisement are distinct capabilities and may require separate enablement.

Incorrect Answers

A:

“Include end-to-end marking tests when deploying voice VLANs and new phone models” belongs to a separate IP Telephony Features issue: a voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. It does not explain the condition tested here.

C:

“Capacity-plan PoE power classes and reserved headroom before connecting new powered devices” belongs to a separate IP Telephony Features issue: a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. It does not explain the condition tested here.

D:

“Test both tagged phone frames and untagged PC frames during phone-port commissioning” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.

Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests

UP

SPECIAL OFFER: GET 10% OFF

This is ONE TIME OFFER

ExamSnap Discount Offer
Enter Your Email Address to Receive Your 10% Off Discount Code

A confirmation link will be sent to this email address to verify your login. *We value your privacy. We will not rent or sell your email address.

Download Free Demo of VCE Exam Simulator

Experience Avanset VCE Exam Simulator for yourself.

Simply submit your e-mail address below to get started with our interactive software demo of your free trial.

Free Demo Limits: In the demo version you will be able to access only first 5 questions from exam.