100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 230
Which suggested shortcut would be especially unsafe for this exact situation? A voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification.
- Review LLDP-MED state and phone compliance during access-switch template audits.
- Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
- Declare the voice QoS requirement met solely because the handset acquired an address in the voice VLAN.
- Synchronize switchport moves with maintained emergency location records.
Explanation
Correct Answer
C:The tempting alternative fails because voice VLAN placement and CoS marking are related but separate; correct VLAN tagging does not guarantee priority handling. The supported action is to verify ingress voice classification, LLDP-MED policy and egress rewrite treatment for voice media.
Incorrect Answers
A:That prevention measure relates to a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature.; it is not the unsafe shortcut described here.
B:That prevention measure relates to a voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a campus changes a telephone port but LLDP-MED location data remains mapped to an old floor.; it is not the unsafe shortcut described here.
Question 231
To prevent recurrence of this precise networking failure, which practice should be adopted? A legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments.
- Include downstream device count and authentication method in desk-port templates.
- Classify interactive and headless endpoint requirements before choosing the access method.
- Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises.
- Review authorization policies for MAC endpoints against a least-privilege access matrix.
Explanation
Correct Answer
D:Review authorization policies for MAC endpoints against a least-privilege access matrix. This guards against MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision.
Incorrect Answers
A:“Include downstream device count and authentication method in desk-port templates” belongs to a separate Layer 2 Authentication and Access Control issue: an access port is placed in single-supplicant mode but a desk phone and PC must authenticate separately behind the same port. It does not explain the condition tested here.
B:“Classify interactive and headless endpoint requirements before choosing the access method” belongs to a separate Layer 2 Authentication and Access Control issue: a noninteractive sensor is trapped in captive-portal onboarding because operators selected browser authentication for all endpoints. It does not explain the condition tested here.
C:“Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises” belongs to a separate Layer 2 Authentication and Access Control issue: an enterprise fallback design accidentally places unauthenticated users into the production network when all RADIUS servers fail. It does not explain the condition tested here.
Question 232
A Junos enterprise team investigates this incident: A new IPv6 peering uses OSPFv3 on a retired VLAN unit rather than the active routed transit interface. Which technical explanation most directly identifies the cause or design principle?
- Local import policy can affect installed route visibility independently of the remote origination of LSAs.
- OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication.
- OSPF database-description exchange can stall when adjacent interfaces disagree on MTU even though basic Hello connectivity exists.
- Routing-policy match criteria must align with the source route type and the intended OSPF export behavior.
Explanation
Correct Answer
B:OSPFv3 adjacency depends on participating interfaces and valid IPv6 link-local neighbor communication. The appropriate response is to move OSPFv3 participation to the correct active interface and verify neighbor and IPv6 RIB state.
Incorrect Answers
A:“Local import policy can affect installed route visibility independently of the remote origination of LSAs” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability. It does not explain the condition tested here.
C:“OSPF database-description exchange can stall when adjacent interfaces disagree on MTU even though basic Hello connectivity exists” belongs to a separate Interior Gateway Protocols (IGPs) issue: two EX distribution routers in OSPF area 0 remain in ExStart after a new transit VLAN uses inconsistent interface MTUs. It does not explain the condition tested here.
D:“Routing-policy match criteria must align with the source route type and the intended OSPF export behavior” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPF export term filters routes based on the wrong protocol, so an intended static default is not originated. It does not explain the condition tested here.
Question 233
A network change is required for the following specific situation: A security function needs to classify a subset of traffic by source and destination criteria rather than trusted external markings. Which corrective action is most appropriate?
- Configure supported egress shaping at the bottleneck and verify throughput and queue behavior.
- Apply the appropriate interface rewrite rule and verify the contract-specific egress code points.
- Use a permitted firewall or multifield classifier matching the approved traffic fields and assign its forwarding class.
- Assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.
Explanation
Correct Answer
C:Multifield classification can use packet fields for policy distinctions beyond incoming BA header code-point classification. Verify this by checking that only traffic meeting the defined match receives the intended queue and packet loss priority.
Incorrect Answers
A:“Configure supported egress shaping at the bottleneck and verify throughput and queue behavior” belongs to a separate Class of Service (CoS) issue: a branch link should pace scheduled traffic to a slower uplink yet the team only drops excess packets abruptly. It does not explain the condition tested here.
B:“Apply the appropriate interface rewrite rule and verify the contract-specific egress code points” belongs to a separate Class of Service (CoS) issue: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It does not explain the condition tested here.
D:“Assign the intended service class and scheduler priorities with measured bandwidth needs, then validate” belongs to a separate Class of Service (CoS) issue: a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. It does not explain the condition tested here.
Question 234
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A new L3 VLAN permits unicast connectivity but the PIM Hello adjacency remains absent on the active path.
- Enable PIM on the approved routed VLAN interface and inspect neighbor and join state.
- Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links.
- The required PIM neighbors appear and downstream join state tracks active interested receivers.
- Enable the same full-bandwidth unicast copy to every receiver and call it multicast optimization.
- Create an IGMP group entry alone and expect it to establish PIM adjacency between routers.
Explanation
Correct Answers
A:Enable PIM on the approved routed VLAN interface and inspect neighbor and join state. This addresses the dependency that PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.
C:The required PIM neighbors appear and downstream join state tracks active interested receivers. The specific steps required are to enable PIM on the approved routed VLAN interface and inspect neighbor and join state.
Incorrect Answers
B:“Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links” is an unsafe response to a different problem: multicast packets arrive on the wrong uplink after unicast routing changes and are dropped by the campus core. It is not a valid fix here.
D:“Enable the same full-bandwidth unicast copy to every receiver and call it multicast optimization” is an unsafe response to a different problem: a trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone. It is not a valid fix here.
E:“Create an IGMP group entry alone and expect it to establish PIM adjacency between routers” does not address PIM routing adjacencies require appropriate protocol participation on the actual routed interfaces used for the distribution tree.
Question 235
A network change is required for the following specific situation: A campus extension carries the right VXLAN outer header but directs frames to the wrong tenant bridge domain due to bad VNI mapping. Which corrective action is most appropriate?
- Inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally.
- Inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.
- Align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes.
- Compare VLAN-to-VNI and bridge-domain assignments on all leafs and correct them against the approved tenant map.
Explanation
Correct Answer
D:VNI and bridge-domain mapping determines tenant overlay segmentation; misaligned mappings can misdeliver or isolate traffic. Verify this by checking that tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated.
Incorrect Answers
A:“Inspect the route type appropriate to the claimed control-plane information instead of treating all EVPN NLRIs equally” belongs to a separate EVPN issue: a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. It does not explain the condition tested here.
B:“Inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration” belongs to a separate EVPN issue: a dual-attached Ethernet segment experiences persistent duplicates during link recovery because multihoming election or ESI state differs. It does not explain the condition tested here.
C:“Align the intended ESI and supported LAG mode, then inspect relevant EVPN Type 1 and Type 4 routes” belongs to a separate EVPN issue: a shared Ethernet segment loses its fast convergence properties after an ESI-LAG peer receives an inconsistent configuration. It does not explain the condition tested here.
Question 236
Select THREE complementary corrective, verification, or preventive controls for this scenario: A network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN.
- Root and forwarding roles match the approved topology under normal and failover conditions.
- Keep explicit root priority policy and validate elections after device replacement.
- Assume the physically fastest switch is always elected as spanning-tree root irrespective of priority.
- Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated.
- Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN.
- Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.
Explanation
Correct Answers
A:Confirmation: Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.
B:Prevention of recurrence: Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
F:Correction: Spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
Incorrect Answers
C:“Assume the physically fastest switch is always elected as spanning-tree root irrespective of priority” does not address spanning-tree root choice and path costs govern forwarding paths; unplanned priority changes can alter traffic patterns.
D:“Remove customer inner VLAN tags at entry and assume overlapping customer IDs remain isolated” is an unsafe response to a different problem: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It is not a valid fix here.
E:“Treat ordinary VLAN membership as equivalent to isolation between every port inside that VLAN” is an unsafe response to a different problem: a shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It is not a valid fix here.
Question 237
The team believes it has resolved this Junos issue: An aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. Which observation best verifies the specific intended result?
- Root and forwarding roles match the approved topology under normal and failover conditions.
- Selected voice and data VLANs use the approved active links without loops.
- Two isolated tenant ports cannot reach each other but can reach the permitted gateway uplink.
- Two customers can use overlapping inner VLAN numbers without traffic mixing on the transport.
Explanation
Correct Answer
D:Two customers can use overlapping inner VLAN numbers without traffic mixing on the transport. This checks the relevant result after design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
Incorrect Answers
A:“Root and forwarding roles match the approved topology under normal and failover conditions” belongs to a separate Ethernet Switching and Spanning Tree issue: a switch with an unexpectedly low bridge priority becomes MSTP root and redirects aggregation traffic through an access closet. It does not explain the condition tested here.
B:“Selected voice and data VLANs use the approved active links without loops” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.
C:“Two isolated tenant ports cannot reach each other but can reach the permitted gateway uplink” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It does not explain the condition tested here.
Question 238
The team believes it has resolved this Junos issue: An OSPF import policy hides external routes on one device while neighbors retain them, confusing the team reviewing reachability. Which observation best verifies the specific intended result?
- The remote inet6.0 table learns the intended loopback and reachability testing succeeds.
- The expected prefix becomes active locally while unwanted external prefixes remain filtered.
- The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency.
- The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change.
Explanation
Correct Answer
B:The expected prefix becomes active locally while unwanted external prefixes remain filtered. This checks the relevant result after compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.
Incorrect Answers
A:“The remote inet6.0 table learns the intended loopback and reachability testing succeeds” belongs to a separate Interior Gateway Protocols (IGPs) issue: a replacement router has IPv6 OSPFv3 adjacency yet does not advertise the loopback subnet required for monitoring. It does not explain the condition tested here.
C:“The team explains the selected active route and verifies intended failover without disturbing OSPFv3 adjacency” belongs to a separate Interior Gateway Protocols (IGPs) issue: a team wrongly concludes OSPFv3 failed when inet6.0 shows a static route active and the OSPFv3 candidate inactive. It does not explain the condition tested here.
D:“The peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change” belongs to a separate Interior Gateway Protocols (IGPs) issue: two EX distribution routers in OSPF area 0 remain in ExStart after a new transit VLAN uses inconsistent interface MTUs. It does not explain the condition tested here.
Question 239
Which suggested shortcut would be especially unsafe for this exact situation? A RADIUS server reports no Access-Request for a silent legacy terminal, while switch timers show no EAP response.
- Rotate every user's password without checking whether the endpoint sent an EAP response at all.
- Track hardware, software edition and port family when standardizing access policies.
- Require inventory ownership and anomaly monitoring for MAC RADIUS exceptions.
- Test fail-open/fail-closed decisions and platform-specific fallback capabilities in disaster recovery exercises.
Explanation
Correct Answer
A:The tempting alternative fails because supplicant absence is a distinct failure from an invalid credential or unreachable authentication server. The supported action is to inspect packet exchange and classify the endpoint before selecting a supported fallback method.
Incorrect Answers
B:That prevention measure relates to an engineer copies legacy 802.1X fallback settings to a platform whose supported feature matrix excludes them.; it is not the unsafe shortcut described here.
C:That prevention measure relates to a MAC RADIUS device changes its network adapter and can no longer authenticate because its registered identifier is stale.; it is not the unsafe shortcut described here.
D:That prevention measure relates to an enterprise fallback design accidentally places unauthenticated users into the production network when all RADIUS servers fail.; it is not the unsafe shortcut described here.
Question 240
A network change is required for the following specific situation: A printer's MAC address is duplicated by an unauthorized endpoint that obtains the same weak MAC-based policy. Which corrective action is most appropriate?
- Confirm the actual device and approved MAC record, then restrict the resulting authorization and add compensating controls.
- Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration.
- Check authentication result classification and map the rejected user to an appropriate deny or reject response.
- Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods.
Explanation
Correct Answer
A:MAC-based identity is tied to the observed hardware address and can be spoofed; it is not strong user authentication. Verify this by checking that only the inventoried device has the expected limited connectivity; rogue or unknown hardware is denied.
Incorrect Answers
B:“Inspect switch authenticator state and RADIUS reachability and identity settings, then repair the approved server configuration” belongs to a separate Layer 2 Authentication and Access Control issue: a campus access interface keeps a compliant supplicant blocked while EAP requests never reach the expected authentication backend. It does not explain the condition tested here.
C:“Check authentication result classification and map the rejected user to an appropriate deny or reject response” belongs to a separate Layer 2 Authentication and Access Control issue: a credential-rejected user is sent to the guest VLAN even though the planned design reserves guest VLAN for silent non-supplicants. It does not explain the condition tested here.
D:“Consult the target release's official 802.1X support matrix and adapt the authorization design to supported methods” belongs to a separate Layer 2 Authentication and Access Control issue: an access switch is moved to Junos OS Evolved but the team assumes every earlier guest-VLAN feature still exists on L2 802.1X interfaces. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests