100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 250
To prevent recurrence of this precise networking failure, which practice should be adopted? A phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature.
- Include end-to-end marking tests when deploying voice VLANs and new phone models.
- Review LLDP-MED state and phone compliance during access-switch template audits.
- Capacity-plan PoE power classes and reserved headroom before connecting new powered devices.
- Test both tagged phone frames and untagged PC frames during phone-port commissioning.
Explanation
Correct Answer
B:Review LLDP-MED state and phone compliance during access-switch template audits. This guards against base LLDP discovery and LLDP-MED telephony advertisement are distinct capabilities and may require separate enablement.
Incorrect Answers
A:“Include end-to-end marking tests when deploying voice VLANs and new phone models” belongs to a separate IP Telephony Features issue: a voice VLAN is configured correctly yet the switch's trust and rewrite policy fails to preserve the required phone traffic classification. It does not explain the condition tested here.
C:“Capacity-plan PoE power classes and reserved headroom before connecting new powered devices” belongs to a separate IP Telephony Features issue: a high-power phone intermittently reboots whenever all powered endpoints on a switch chassis start simultaneously. It does not explain the condition tested here.
D:“Test both tagged phone frames and untagged PC frames during phone-port commissioning” belongs to a separate IP Telephony Features issue: a desk phone sends tagged voice traffic, but the switchport permits only the untagged data VLAN. It does not explain the condition tested here.
Question 251
For this case, select TWO complementary measures or outcome checks that directly resolve the problem: A trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone.
- Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links.
- Disable IGMP snooping everywhere and assume uncontrolled flooding is equivalent to correct membership delivery.
- Enable the same full-bandwidth unicast copy to every receiver and call it multicast optimization.
- Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream.
- Design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths.
Explanation
Correct Answers
D:Backbone utilization reflects one upstream multicast copy per tree branch while interested receivers obtain the stream. The specific steps required are to design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths.
E:Design a multicast distribution tree with explicit receiver memberships and test only the subscribed delivery paths. This addresses the dependency that IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream.
Incorrect Answers
A:“Turn off all RPF checking to accept duplicate or looping multicast packets from arbitrary links” is an unsafe response to a different problem: multicast packets arrive on the wrong uplink after unicast routing changes and are dropped by the campus core. It is not a valid fix here.
B:“Disable IGMP snooping everywhere and assume uncontrolled flooding is equivalent to correct membership delivery” is an unsafe response to a different problem: an access VLAN floods every multicast packet because IGMP snooping state was lost during migration. It is not a valid fix here.
C:“Enable the same full-bandwidth unicast copy to every receiver and call it multicast optimization” does not address IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream.
Question 252
A network change is required for the following specific situation: Two EX distribution routers in OSPF area 0 remain in ExStart after a new transit VLAN uses inconsistent interface MTUs. Which corrective action is most appropriate?
- Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter.
- Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
- Compare interface MTUs and OSPF neighbor states, then align the supported interface MTU on both endpoints.
- Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs.
Explanation
Correct Answer
C:OSPF database-description exchange can stall when adjacent interfaces disagree on MTU even though basic Hello connectivity exists. Verify this by checking that the peers advance to Full and successfully exchange database summaries after an approved aligned-MTU change.
Incorrect Answers
A:“Compare LSDB advertisements with local route policy and inet.0 state; correct the intended import filter” belongs to a separate Interior Gateway Protocols (IGPs) issue: a core node shows a missing route while remote LSDBs include the corresponding external LSA after a local policy change. It does not explain the condition tested here.
B:“Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.
D:“Restrict the export policy to explicit approved route prefixes and protocols, then check external LSAs” belongs to a separate Interior Gateway Protocols (IGPs) issue: an ABR starts leaking a management static route into the enterprise IGP after a permissive export term was introduced. It does not explain the condition tested here.
Question 253
To prevent recurrence of this precise networking failure, which practice should be adopted? A campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them.
- Track MSTP instance scale and maintain identical region parameters across participating switches.
- Include packet-capture verification of S-tag and C-tag transformation in provider handoffs.
- Maintain representative match and nonmatch tests for filter-based VLAN policies.
- Test each critical VLAN's root bridge and forwarding path after VSTP updates.
Explanation
Correct Answer
C:Maintain representative match and nonmatch tests for filter-based VLAN policies. This guards against filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point.
Incorrect Answers
A:“Track MSTP instance scale and maintain identical region parameters across participating switches” belongs to a separate Ethernet Switching and Spanning Tree issue: a network uses one VLAN-wide topology but wants two forwarding trees for different groups without an instance for every VLAN. It does not explain the condition tested here.
B:“Include packet-capture verification of S-tag and C-tag transformation in provider handoffs” belongs to a separate Ethernet Switching and Spanning Tree issue: customer traffic emerges with the provider service tag still attached and is rejected by an endpoint expecting ordinary Ethernet. It does not explain the condition tested here.
D:“Test each critical VLAN's root bridge and forwarding path after VSTP updates” belongs to a separate Ethernet Switching and Spanning Tree issue: a legacy interop design needs separate per-VLAN spanning-tree compatibility but all VLANs inherit one unsuitable tree. It does not explain the condition tested here.
Question 254
The team believes it has resolved this Junos issue: An EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. Which observation best verifies the specific intended result?
- Full-sized authorized frames traverse the VXLAN tunnel without unexpected fragmentation or blackholing.
- BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered.
- BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates.
- The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types.
Explanation
Correct Answer
A:Full-sized authorized frames traverse the VXLAN tunnel without unexpected fragmentation or blackholing. This checks the relevant result after test larger encapsulated frames and align supported underlay and overlay MTUs without disabling unrelated protections.
Incorrect Answers
B:“BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered” belongs to a separate EVPN issue: a bridge domain has valid unicast Type 2 entries yet remote VTEPs do not discover a new participating segment for BUM forwarding. It does not explain the condition tested here.
C:“BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates” belongs to a separate EVPN issue: an EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior. It does not explain the condition tested here.
D:“The expected MAC/IP binding is visible in Type 2 while multihoming and BUM state use their own route types” belongs to a separate EVPN issue: a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. It does not explain the condition tested here.
Question 255
A Junos enterprise team investigates this incident: A network marks a customer route with a community but an export policy ignores the community, leaking the route to another peer. Which technical explanation most directly identifies the cause or design principle?
- MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions.
- Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints.
- Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it.
- For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner.
Explanation
Correct Answer
C:Communities are policy metadata; tagging does not enforce advertisement restrictions unless a matching policy acts on it. The appropriate response is to inspect received communities and export policy terms, then attach a tested community match and reject rule.
Incorrect Answers
A:“MED has lower precedence than LOCAL_PREF and AS-path in common BGP best-path selection and must be compared under supported conditions” belongs to a separate Border Gateway Protocol (BGP) issue: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It does not explain the condition tested here.
B:“Multihop BGP peerings require suitable routing to endpoint addresses and peer-session settings for nonadjacent endpoints” belongs to a separate Border Gateway Protocol (BGP) issue: a transit peering is moved off directly connected interface IPs to loopbacks yet the TTL and reachability design are not updated. It does not explain the condition tested here.
D:“For eligible BGP candidates, LOCAL_PREF comparison precedes AS-path length, so AS-path length alone does not determine the winner” belongs to a separate Border Gateway Protocol (BGP) issue: a router prefers a longer AS path when a higher LOCAL_PREF makes that route win, surprising the transit team. It does not explain the condition tested here.
Question 256
The team believes it has resolved this Junos issue: Packets with two different drop precedence values are treated as equally discardable during congestion. Which observation best verifies the specific intended result?
- Queue depth, latency and drop statistics meet documented objectives during realistic traffic load.
- Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses.
- Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses.
- During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic.
Explanation
Correct Answer
D:During controlled congestion, out-of-profile traffic experiences earlier drops than in-profile traffic. This checks the relevant result after map the two packet categories to the intended PLP levels and verify drop-profile response.
Incorrect Answers
A:“Queue depth, latency and drop statistics meet documented objectives during realistic traffic load” belongs to a separate Class of Service (CoS) issue: a backup traffic queue consumes too much buffer and latency-sensitive applications starve during peak bursts. It does not explain the condition tested here.
B:“Outgoing traffic conforms to the contracted rate with acceptable delay and fewer burst losses” belongs to a separate Class of Service (CoS) issue: a WAN customer requires smooth outbound transmission but an ingress drop policer creates unnecessary burst loss. It does not explain the condition tested here.
C:“Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses” belongs to a separate Class of Service (CoS) issue: a finance video queue configured as low priority cannot meet latency targets because competing transfers share the same service policy. It does not explain the condition tested here.
Question 257
Select THREE complementary corrective, verification, or preventive controls for this scenario: An EVPN multihomed endpoint creates duplicate forwarding when two leafs both forward the same BUM traffic without appropriate split-horizon behavior.
- Read a Type 1 Ethernet auto-discovery update as the definitive source of every individual host MAC address.
- Increase a tenant VLAN identifier and expect it to fix an unreachable underlay VTEP IP.
- Inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.
- Test multihoming election and per-VLAN failover after attaching new dual-homed devices.
- BUM traffic follows permitted designated-forwarder behavior with no persistent looping duplicates.
- Enable independent active forwarding on every multihomed link while ignoring ESI and DF controls.
Explanation
Correct Answers
C:Correction: EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.
D:Prevention of recurrence: EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.
E:Confirmation: Inspect shared ESI, DF election and Ethernet-segment routes, then correct the multihoming configuration.
Incorrect Answers
A:“Read a Type 1 Ethernet auto-discovery update as the definitive source of every individual host MAC address” is an unsafe response to a different problem: a troubleshooting team expects EVPN Ethernet auto-discovery route Type 1 to carry all host MAC/IP bindings. It is not a valid fix here.
B:“Increase a tenant VLAN identifier and expect it to fix an unreachable underlay VTEP IP” is an unsafe response to a different problem: a VXLAN overlay's BGP EVPN routes are present, but the underlay cannot route to a remote VTEP loopback. It is not a valid fix here.
F:“Enable independent active forwarding on every multihomed link while ignoring ESI and DF controls” does not address EVPN multihoming uses Ethernet segment identification and designated-forwarder or split-horizon rules to avoid loops.
Question 258
A network change is required for the following specific situation: An uplink becomes a region boundary unexpectedly after an administrator changes an MSTP configuration name on only one switch. Which corrective action is most appropriate?
- Compare complete region configuration on the peers and restore the approved shared MSTP region values.
- Configure supported L2PT for the required control protocols and verify provider-edge handling.
- Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule.
- Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
Explanation
Correct Answer
A:MSTP region membership depends on compatible region parameters such as name, revision and VLAN-to-instance map. Verify this by checking that both switches show compatible region membership and intended instance root/port roles.
Incorrect Answers
B:“Configure supported L2PT for the required control protocols and verify provider-edge handling” belongs to a separate Ethernet Switching and Spanning Tree issue: a private L2 service must extend customer control protocols, yet the provider fabric consumes or drops the customer's BPDUs. It does not explain the condition tested here.
C:“Inspect match conditions and attachment point, then change the approved filter-based VLAN steering rule” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them. It does not explain the condition tested here.
D:“Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress” belongs to a separate Ethernet Switching and Spanning Tree issue: an aggregation network sees customer VLAN IDs collide because several tenants share the same single-tagged provider infrastructure. It does not explain the condition tested here.
Question 259
A network change is required for the following specific situation: Two newly deployed distribution switches report identical OSPF router IDs, causing inconsistent LSAs in the area. Which corrective action is most appropriate?
- Inspect inet6.0 route detail and route preferences before changing OSPFv3 neighbor configuration.
- Inspect the active local default and export term conditions; match only the authorized static default source.
- Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface.
- Assign unique stable router IDs, confirm interfaces, and recheck adjacency and LSDB after controlled reconvergence.
Explanation
Correct Answer
D:OSPF identifies routers by unique router ID; collisions can destabilize LSDB and adjacency behavior. Verify this by checking that no router-ID collision appears and OSPF paths stabilize with expected next hops.
Incorrect Answers
A:“Inspect inet6.0 route detail and route preferences before changing OSPFv3 neighbor configuration” belongs to a separate Interior Gateway Protocols (IGPs) issue: an IPv6 route learned through OSPFv3 is absent from the forwarding table because a more preferred static route covers the same prefix. It does not explain the condition tested here.
B:“Inspect the active local default and export term conditions; match only the authorized static default source” belongs to a separate Interior Gateway Protocols (IGPs) issue: a branch default-route injection stops after a policy matches OSPF-learned routes instead of the intended local static. It does not explain the condition tested here.
C:“Check IPv6 link-local addressing, OSPFv3 neighbor state and relevant ICMPv6 connectivity on the actual interface” belongs to a separate Interior Gateway Protocols (IGPs) issue: an OSPFv3 adjacency on a dual-stack campus changes state because engineers treat IPv4 interface reachability as proof of IPv6 control-plane health. It does not explain the condition tested here.
Question 260
To prevent recurrence of this precise networking failure, which practice should be adopted? A multicast team changes unicast routing yet an engineered multicast RPF table still points to an obsolete next hop.
- Document ASM/SSM selection and receiver-version prerequisites before multicast deployment.
- Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes.
- Maintain consistent RP mappings and failover tests across multicast routers.
- Include routed-interface PIM enrollment in the multicast deployment checklist.
Explanation
Correct Answer
B:Document whether multicast RPF uses inet.0 or inet.2 and verify after topology changes. This guards against Junos multicast RPF may use a dedicated routing table, so the effective RPF path must be inspected, not guessed from unicast traffic.
Incorrect Answers
A:“Document ASM/SSM selection and receiver-version prerequisites before multicast deployment” belongs to a separate IP Multicast issue: a video source is known and receivers support IGMPv3, but engineers configure ASM and an RP unnecessarily for the source-specific application. It does not explain the condition tested here.
C:“Maintain consistent RP mappings and failover tests across multicast routers” belongs to a separate IP Multicast issue: an ASM video distribution has valid listener memberships yet PIM joins never converge toward the configured RP. It does not explain the condition tested here.
D:“Include routed-interface PIM enrollment in the multicast deployment checklist” belongs to a separate IP Multicast issue: a new L3 VLAN permits unicast connectivity but the PIM Hello adjacency remains absent on the active path. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests