100% Latest & Updated Juniper JN0-650 Practice Test Questions, Exam Dumps & Verified Answers!
30 Days Free Updates, Instant Download!
Question 710
A Junos enterprise team investigates this incident: A dynamic VLAN is removed from one edge but stale MVRP registration keeps an unused VLAN active downstream. Which technical explanation most directly identifies the cause or design principle?
- Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point.
- MVRP registrations can persist where membership state or participation has not been updated consistently.
- Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink.
- A private VLAN community allows permitted communication within its community; isolated behavior is stricter.
Explanation
Correct Answer
B:MVRP registrations can persist where membership state or participation has not been updated consistently. The appropriate response is to inspect registration state and remove stale VLAN membership while preserving necessary registrations.
Incorrect Answers
A:“Filter-based VLAN assignment depends on correctly matching the selected traffic and applying the filter at the right ingress point” belongs to a separate Ethernet Switching and Spanning Tree issue: a campus onboarding policy puts cameras on the normal data VLAN even though a targeted filter-based VLAN should steer them. It does not explain the condition tested here.
C:“Private VLAN isolated ports are designed to limit lateral L2 communication while still reaching the permitted promiscuous uplink” belongs to a separate Ethernet Switching and Spanning Tree issue: a shared guest access VLAN allows two untrusted hotel-room ports to communicate directly, violating the isolation design. It does not explain the condition tested here.
D:“A private VLAN community allows permitted communication within its community; isolated behavior is stricter” instead concerns another network scenario: Members of the same trusted workgroup are accidentally placed in isolated rather than community PVLAN ports and lose peer communication. It does not address the requirement here.
Question 711
A network change is required for the following specific situation: A building's private VLAN design inadvertently limits tenant access to a shared printer uplink while direct tenant communication is supposed to stay blocked. Which corrective action is most appropriate?
- Inspect the primary/secondary association to shared-service promiscuous ports, then correct only authorized connectivity.
- Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress.
- Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles.
- Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately.
Explanation
Correct Answer
A:Private VLAN communication depends on permitted mappings to promiscuous ports and permitted community or isolated roles. Verify this by checking that isolated clients reach the shared service but cannot communicate laterally with other isolated clients.
Incorrect Answers
B:“Design supported stacked VLAN tagging and verify S-tag/C-tag placement at the correct ingress and egress” belongs to a separate Ethernet Switching and Spanning Tree issue: a service provider must carry multiple customer VLAN IDs transparently over one metro Ethernet handoff. It does not explain the condition tested here.
C:“Remove incorrect edge treatment, validate BPDU reception and restore loop-free port roles” belongs to a separate Ethernet Switching and Spanning Tree issue: a redundant L2 topology creates a broadcast storm after an edge port connected to another switch is treated as an endpoint. It does not explain the condition tested here.
D:“Compare bridge priority, VLAN or MSTI root and port path costs against design; adjust deliberately” belongs to a separate Ethernet Switching and Spanning Tree issue: a network replacement changes VSTP root elections, causing backup links to forward for a critical VLAN. It does not explain the condition tested here.
Question 712
The team believes it has resolved this Junos issue: Two queues use the same scheduler priority, but the business expects one to always win during contention. Which observation best verifies the specific intended result?
- Control-plane-related traffic receives the expected queue treatment under simulated load.
- Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic.
- Only traffic meeting the defined match receives the intended queue and packet loss priority.
- Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses.
Explanation
Correct Answer
D:Under controlled congestion, critical media meets its objective while permitted best-effort traffic still progresses. This checks the relevant result after assign the intended service class and scheduler priorities with measured bandwidth needs, then validate.
Incorrect Answers
A:“Control-plane-related traffic receives the expected queue treatment under simulated load” belongs to a separate Class of Service (CoS) issue: a forwarding-class configuration sends critical routing packets to a queue used for bulk backups and adjacency stability degrades under load. It does not explain the condition tested here.
B:“Packet captures show the intended DSCP or 802.1p fields on outbound voice, video and data traffic” belongs to a separate Class of Service (CoS) issue: a provider handoff expects specific code-point markings yet a trunk rewrites every service class to default behavior. It does not explain the condition tested here.
C:“Only traffic meeting the defined match receives the intended queue and packet loss priority” belongs to a separate Class of Service (CoS) issue: a security function needs to classify a subset of traffic by source and destination criteria rather than trusted external markings. It does not explain the condition tested here.
Question 713
A Junos enterprise team investigates this incident: After a RADIUS outage, the access switch opens ports broadly instead of applying the approved restricted server-fail VLAN. Which technical explanation most directly identifies the cause or design principle?
- Captive portal requires a supported browser interception and authentication-to-authorization sequence.
- MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision.
- Server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access.
- MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X.
Explanation
Correct Answer
C:Server-fail fallback must be an explicitly scoped authorization policy; availability cannot justify unbounded access. The appropriate response is to use a supported restricted server-fail policy and validate failure handling on the specific Junos platform.
Incorrect Answers
A:“Captive portal requires a supported browser interception and authentication-to-authorization sequence” belongs to a separate Layer 2 Authentication and Access Control issue: a visitor portal redirects browser traffic but never releases the user to the approved network after authentication. It does not explain the condition tested here.
B:“MAC authorization should couple weak identity to constrained role-based network access, not just a successful RADIUS decision” belongs to a separate Layer 2 Authentication and Access Control issue: a legacy printer can join after MAC authentication yet is allowed to reach sensitive management segments. It does not explain the condition tested here.
D:“MAC RADIUS provides a fallback identity mechanism for suitable non-802.1X devices, with weaker assurance than certificate-based 802.1X” belongs to a separate Layer 2 Authentication and Access Control issue: a non-802.1X network printer is consistently rejected because its access port permits only EAP supplicants. It does not explain the condition tested here.
Question 714
Which suggested shortcut would be especially unsafe for this exact situation? A route-reflector client receives an external destination but lacks the underlay path to the advertised next hop.
- Review policy ordering with negative tests and explicit default actions on every change.
- Test expected best-path behavior before modifying LOCAL_PREF across internal peers.
- Assume TCP session Established proves every learned prefix has a usable forwarding next hop.
- Maintain community inventories and test outbound policy outcomes for allowed and denied prefixes.
Explanation
Correct Answer
C:The tempting alternative fails because a reachable BGP peering session does not itself make a third-party route next hop recursively resolvable. The supported action is to inspect next-hop attributes and IGP reachability; deliberately choose appropriate next-hop-self policy or add valid underlay routes.
Incorrect Answers
A:That prevention measure relates to a route with a permissive policy term is accepted before a later deny term can block it.; it is not the unsafe shortcut described here.
B:That prevention measure relates to an enterprise chooses a different BGP exit after import policy assigns a higher local preference to the backup path.; it is not the unsafe shortcut described here.
D:That prevention measure relates to a provider-facing policy stops honoring a route-tag community after a new import policy changes the attached communities.; it is not the unsafe shortcut described here.
Question 715
The team believes it has resolved this Junos issue: Two eBGP sessions over different transports are expected to provide ECMP but only one forwarding next hop appears. Which observation best verifies the specific intended result?
- Allowed customer prefixes are received while unauthorized longer prefixes are absent from accepted routes.
- The route is accepted only after the AS-path loop is removed, with stable forwarding.
- The routing and forwarding tables show the intended multiple next hops only for qualifying routes.
- The unauthorized route is rejected while intended export cases still match the proper terms.
Explanation
Correct Answer
C:The routing and forwarding tables show the intended multiple next hops only for qualifying routes. This checks the relevant result after compare BGP best-path and multipath eligibility conditions, then enable approved multipath behavior and validate forwarding.
Incorrect Answers
A:“Allowed customer prefixes are received while unauthorized longer prefixes are absent from accepted routes” belongs to a separate Border Gateway Protocol (BGP) issue: an eBGP import policy unexpectedly accepts more-specific prefixes outside the approved customer allocation. It does not explain the condition tested here.
B:“The route is accepted only after the AS-path loop is removed, with stable forwarding” belongs to a separate Border Gateway Protocol (BGP) issue: a carrier changes an upstream routing arrangement and a downstream Junos router detects its own AS in the advertised AS path. It does not explain the condition tested here.
D:“The unauthorized route is rejected while intended export cases still match the proper terms” belongs to a separate Border Gateway Protocol (BGP) issue: a BGP export configuration has a broad first match so a specific downstream deny never evaluates the target prefix. It does not explain the condition tested here.
Question 716
To prevent recurrence of this precise networking failure, which practice should be adopted? A trading-data sender needs to serve many local subscribers, but each listener receives its own redundant copy over the backbone.
- Monitor IGMP membership churn and snooping state when moving clients between VLANs.
- Check multicast and unicast topology alignment whenever routing paths or metrics change.
- Measure receiver interest and multicast forwarding state before scaling new one-to-many services.
- Test RP failover and synchronization behavior before expanding Anycast RP.
Explanation
Correct Answer
C:Measure receiver interest and multicast forwarding state before scaling new one-to-many services. This guards against IP multicast replicates streams at forwarding branches instead of requiring a separate source-to-receiver unicast stream.
Incorrect Answers
A:“Monitor IGMP membership churn and snooping state when moving clients between VLANs” belongs to a separate IP Multicast issue: an access VLAN floods every multicast packet because IGMP snooping state was lost during migration. It does not explain the condition tested here.
B:“Check multicast and unicast topology alignment whenever routing paths or metrics change” belongs to a separate IP Multicast issue: an alternate upstream sends multicast on a path different from the router's route back to the source, causing RPF failures. It does not explain the condition tested here.
D:“Test RP failover and synchronization behavior before expanding Anycast RP” belongs to a separate IP Multicast issue: an Anycast RP design uses two RP addresses that do not share the intended anycast identity, producing inconsistent joins. It does not explain the condition tested here.
Question 717
Select THREE complementary corrective, verification, or preventive controls for this scenario: Equal candidate BGP routes are visible but no multipath forwarding entry is installed because eligibility or policy differs.
- Compare BGP best-path and multipath eligibility conditions, then enable approved multipath behavior and validate forwarding.
- The routing and forwarding tables show the intended multiple next hops only for qualifying routes.
- Test path equivalence, forwarding and failure convergence before enabling transit ECMP.
- Use only the MED field as guaranteed proof of the selected route regardless of preceding BGP attributes.
- Add a second BGP neighbor and assume the forwarding table automatically load-balances every route.
- Accept every prefix inside the aggregate without evaluating the agreed maximum prefix length.
Explanation
Correct Answers
A:Correction: BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions.
B:Confirmation: Compare BGP best-path and multipath eligibility conditions, then enable approved multipath behavior and validate forwarding.
C:Prevention of recurrence: BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions.
Incorrect Answers
D:“Use only the MED field as guaranteed proof of the selected route regardless of preceding BGP attributes” is an unsafe response to a different problem: two equal LOCAL_PREF and AS-path candidates remain tied until MED influences the choice under the applicable comparison rules. It is not a valid fix here.
E:“Add a second BGP neighbor and assume the forwarding table automatically load-balances every route” does not address BGP equal-cost multipath requires appropriate configured support and matching eligible path attributes, not merely two established sessions.
F:“Accept every prefix inside the aggregate without evaluating the agreed maximum prefix length” is an unsafe response to a different problem: a prefix-list matches a broad aggregate but accepts unwanted subprefixes from a new external neighbor. It is not a valid fix here.
Question 718
The team believes it has resolved this Junos issue: A VNI is active on two leafs but unknown-unicast or broadcast replication never reaches the remote side. Which observation best verifies the specific intended result?
- Tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated.
- Both peers report a consistent Ethernet segment and failover preserves authorized connectivity.
- Full-sized authorized frames traverse the VXLAN tunnel without unexpected fragmentation or blackholing.
- BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered.
Explanation
Correct Answer
D:BUM traffic reaches only participating VTEPs and the remote endpoint can be discovered. This checks the relevant result after inspect Type 3 routes and VNI import/export membership; repair the intended inclusive-multicast advertisement.
Incorrect Answers
A:“Tenant traffic reaches only its intended remote bridge domain and overlapping VLAN IDs remain isolated” belongs to a separate EVPN issue: a fabric uses conflicting VLAN-to-VNI mappings on two leaf switches, bridging different tenant segments together. It does not explain the condition tested here.
B:“Both peers report a consistent Ethernet segment and failover preserves authorized connectivity” belongs to a separate EVPN issue: a multihomed CE is attached to two leafs but one leaf advertises a different ESI, preventing expected redundancy behavior. It does not explain the condition tested here.
C:“Full-sized authorized frames traverse the VXLAN tunnel without unexpected fragmentation or blackholing” belongs to a separate EVPN issue: an EVPN-VXLAN frame is dropped over a path where the IP underlay MTU was sized only for unencapsulated Ethernet payloads. It does not explain the condition tested here.
Question 719
A network change is required for the following specific situation: A campus uplink transmits marked video as ordinary data because no behavior-aggregate classifier is attached at ingress. Which corrective action is most appropriate?
- Define a controlled rewrite map for each class and verify high-priority markings remain restricted.
- Apply an approved behavior-aggregate classifier with the intended DSCP-to-class mapping on the real ingress interface.
- Apply the appropriate interface rewrite rule and verify the contract-specific egress code points.
- Use a permitted firewall or multifield classifier matching the approved traffic fields and assign its forwarding class.
Explanation
Correct Answer
B:Junos ingress classifiers map packet header code points to forwarding classes and packet loss priority, subject to interface attachment. Verify this by checking that observed queue counters show voice packets in the designated forwarding class after classification.
Incorrect Answers
A:“Define a controlled rewrite map for each class and verify high-priority markings remain restricted” belongs to a separate Class of Service (CoS) issue: a branch egress rewriter incorrectly gives bulk backups the same DSCP as real-time voice. It does not explain the condition tested here.
C:“Apply the appropriate interface rewrite rule and verify the contract-specific egress code points” belongs to a separate Class of Service (CoS) issue: a boundary router classifies EF voice traffic correctly but sends outbound DSCP zero, so downstream devices undo priority handling. It does not explain the condition tested here.
D:“Use a permitted firewall or multifield classifier matching the approved traffic fields and assign its forwarding class” instead concerns another network scenario: An application needs priority regardless of incoming DSCP, but an interface uses only a header-based classifier. It does not address the requirement here.
Question 720
A Junos enterprise team investigates this incident: A voice handset fails to boot on an EX switch port after new cameras consume the remaining PoE budget. Which technical explanation most directly identifies the cause or design principle?
- LLDP-MED location metadata can support telephony location services and must match actual switch-port placement.
- PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status.
- Base LLDP discovery and LLDP-MED telephony advertisement are distinct capabilities and may require separate enablement.
- LLDP-MED extends device discovery with telephony-related network-policy TLVs that need compatible endpoint behavior.
Explanation
Correct Answer
B:PoE availability depends on the supported per-port power class and total switch power budget, not just Ethernet link status. The appropriate response is to check switch PoE budget, negotiated device requirements and per-port allocation, then rebalance or provision supported power.
Incorrect Answers
A:“LLDP-MED location metadata can support telephony location services and must match actual switch-port placement” belongs to a separate IP Telephony Features issue: an IP phone uses the wrong location information for emergency response after a switch move. It does not explain the condition tested here.
C:“Base LLDP discovery and LLDP-MED telephony advertisement are distinct capabilities and may require separate enablement” belongs to a separate IP Telephony Features issue: a phone supports LLDP-MED but the switch sends no med TLVs after a policy template disables the feature. It does not explain the condition tested here.
D:“LLDP-MED extends device discovery with telephony-related network-policy TLVs that need compatible endpoint behavior” belongs to a separate IP Telephony Features issue: a vendor handset discovers its neighbor using basic LLDP but does not learn the configured network policy for voice tagging. It does not explain the condition tested here.
Enterprise Routing and Switching, Professional (JNCIP-ENT) (JN0-650) Practice Tests